1998 SSANGYONG MUSSO transmission oil

1B1-54 M162 ENGINE MECHANICAL
Removal & Installation Procedure
1. Unscrew the stretch bolt.
Installation Notice
Sectional View
1 Oil Pan
2 Cover
3 Crankshaft Front Seal
4 Flywheel MTG Bolt
5 Crankshaft
6 Dowel Pin
7 Plate
8 TGCC
9 Bolt
10 Front Drive Plate
11 Rear Drive Plate
12 Rivet
13 Segment
14 Ring Gear
lReplace the bolt when the stretch side diameter (d) of
the flywheel mounting bolt is less than 8.0mm.
lFor the stretch bolt tightening, keep the socket wrench
and Tommy-bar to be 90° and tighten as specified.
2. Remove the flywheel for manual transmission vehicles, or
the driven plate (3), and plate (2) for Auto. transmission
vehicle.
3. Installation should follow the removal procedure in the
reverse order.Tightening Torque1st step 45+5 Nm
2nd step 90° + 10°

1B2-12 M161 ENGINE MECHANICAL
12. Discharge the refrigerant from A/C system, and disconnect
the discharge pipe and suction pipe from the compressor.
14. Remove the fuel feed and return line.
Notice
Before removing the fuel lines, release the pressure in the
fuel system.
Installation Notice 13. Remove the acceleration control cable and automatic
transmission pressure cable. 11. Remove the hydraulic pipe of power steering.
Notice
Completely drain the oil.
Tightening Torque 21 - 25 Nm

1B2-14 M161 ENGINE MECHANICAL
20. Disconnect following sensors connector.
lHFM sensor.
lCoolant temperature sensor.
l2 knock sensors.
lCamshaft and crankshaft sensors.
21. After removing the ignition coil cover, disconnect the ignition
coil connector.
22. Remove the harness cover and disconnect the 6 injection
valve connectors. Disconnect the main harness.
23. Separate the hose toward engine from canister purge
solenoid valve.
24. Remove the automatic transmission oil cooler line.

M161 ENGINE MECHANICAL 1B2-61
Removal & Installation Procedure
1. Unscrew the stretch bolt.
Installation Notice
Sectional View
1 Oil Pan
2 Cover
3 Radial Seal
4 Bolt
5 Crankshaft
6 Dowel Pin
7 Washer (Thickness : 3.5 mm)
8 Washer
9 Bolt
10 Front Drive Plate
11 Rear Drive Plate
12 Rivet
13 Segment
14 Ring Gear
lReplace the bolt when the stretch side diameter (d) of
the flywheel mounting bolt is less than 8.0mm.
lFor the stretch bolt tightening, keep the socket wrench
and Tommy-bar to be 90° and tighten as specified.
2. Remove the flywheel for manual transmission vehicles,
or the driven plate (3), and plate (2) for Auto. transmission
vehicle.
3. Installation should follow the removal procedure in the
reverse order.Tightening Torque1st step 45 Nm
2nd step90°+5°

1B3-16 OM600 ENGINE MECHANICAL
16. Remove the power steering pump lines.
Notice
Completely drain the fluid.
17. Disconnect the fuel feed line with prefilter from the feed
pump on injection pump.
18. Vehicle with automatic transmission.
Remove the hydraulic lines (19, 20) from oil cooler (2).
19. Disconnect the engine harness.
20. Disconnect the preheating time relay cable.

OM600 ENGINE MECHANICAL 1B3-93
FLYWHEEL
Preceding Work : Removal of the transmission
Removal of the clutch
1 Oil Pan
2 Straight Pin
3 Flywheel4 12-Sided Stretch Bolt............Check, 45Nm + 90°
5 Drive Plate (Automatic Transmission)
6 Flywheel (Automatic Transmission)

1D1-2 M162 ENGINE COOLING
FASTENER TIGHTENING SPECIFICATIONS
N
· ·· ·
·m
30
22.5 - 27.5
9 - 11
9 - 11
9 - 11
40.5 - 49.5
3 - 7
3 - 7 Application
Coolant Drain Plug
Engine Hanger Bracket and Coolant Outlet
Port Bolt
Thermostat Cover Bracket Bolt
Oil Cooler Pipe Line Bolt
Cooling Fan Bolt
Viscous Clutch Bolt
Automatic Transmission Oil Cooling Hose Bolt
Cooling Fan Shroud Bolt

M162 ENGINE COOLING 1D1-15
RADIATOR
Preceding Work : Removal of cooling fan shroud
1 Radiator Inlet Coolant Hose
2 Radiator Outlet Coolant Hose
3 Make Up Coolant Hose
4 Automatic Transmission Oil Cooling Hose
5 Automatic Transmission Oil Cooling Line6 Bolt
7 Insulator
8 Stopper
9 Bolt............................................................. 7 Nm
10 Radiator