1998 SSANGYONG MUSSO tire pressure

Description
Alumimun
7JJ X 15
Radial Tire
P215 / 75R 15 - 30psi
P235 / 75R 15 - 30psi
P255 / 70R 15 - 30psi Application
Wheel
SECTION 2E
TIRES AND WHEELS
TABLE OF CONTENTS
SPECIFICATIONS
GENERAL SPECIFICATIONS
FASTENER TIGHTENING SPECIFICATIONS
Application
Wheel BoltNlm
80 - 120
110 - 130
Specifications . . . . . . . . . . . . . . . . . . . . . . . . 2E-1
General Specifications . . . . . . . . . . . . . . . . . . 2E-1
Fastener Tightening Specifications . . . . . . . . . 2E-1
Diagnosis . . . . . . . . . . . . . . . . . . . . . . . . . . . 2E-2
Wear Pattern Diagnosis . . . . . . . . . . . . . . . . . 2E-2
Identification . . . . . . . . . . . . . . . . . . . . . . . . . 2E-3
Radial Tire . . . . . . . . . . . . . . . . . . . . . . . . . . . 2E-3Wheel Disc . . . . . . . . . . . . . . . . . . . . . . . . . . . 2E-3
Component Locator . . . . . . . . . . . . . . . . . . . 2E-4
Wheel and Tire . . . . . . . . . . . . . . . . . . . . . . . . 2E-4
Maintenance and Repair . . . . . . . . . . . . . . . 2E-5
On-Vehicle Service . . . . . . . . . . . . . . . . . . . . . 2E-5
Wheels and Tires . . . . . . . . . . . . . . . . . . . . . . 2E-5
Material
Size
Tire
Type
Size and Tire Pressure
Steel
Alumimum

2E-6 TIRES AND WHEELS
4. Tire pressure inspection.
lTire pressure.
lCheck tread contact with road.
Notice
lIf underinflated, tire may come away from the wheel
during rapid steering.
lAn overinflated tire will cause a hard riding and uneven
wear.
Front & Rear
(P235/75R15)2.1kg/cm (30PSI)2
5. Wheel balance.
lBalance weights should be on each side. When the wheel
is out of balance or a tire has been repaired, be sure to
balance the wheel again.
lIf total weight is over 150g, readjust the balance by
reinstalling the tire on the wheel.
lBalance weight should not protrude from the wheel rim
over 3mm.
lFor aluminum wheel, use aluminum wheel balance weight
only.

4A-2 HYDRAULIC BRAKES
Check
Dirty or Lack of Fluid
Air in Brake System
Faulty Brake Booster
Poor Contact of Pad or Lining
Oil or Grease on Pad
Faulty Auto Adjuster
Over Heated Rotor Due to Dragging Pad or Lining
Clogging Brake Line
Faulty Proportioning ValveCheck
Incorrect Tire Pressure Between Left and Right
Poor Contact of Pad or Lining
Oil or Grease is Applied to Pad or Lining
Bent or Uneven Wear of Drum
Incorrectly Mounted Wheel Cylinder
Faulty Auto AdjusterAction
Repair
Retighten
Replace
Replace
Repair
Repair
Lubricate
Retighten Check
Incorrectly Mounted Back Plate or Caliper
Loosened Bolt of Back Plate or Caliper
Crack or Uneven Wear of Brake Drum or Disc
Pad or Lining Sticking to Contact Surface
Excessive Clearance Between Caliper and Pad
Uneven Contact of Pad
Lack of Lubrication
Loosened Suspension
DIGNOSIS
NOISE OR VEHICLE VIBRATION WHEN APPLIED BRAKE
PULLS TO ONE SIDE WHEN BRAKING
Action
Adjust
Repair
Replace
Replace
Repair
Replace
Action
Replenish or Replace(Check eventual leakage)
Bleeding
Replace
Repair
Replace
Replace
Repair
Repair
Repair
POOR BRAKING
( If low cut-in : Adjust )
( If Leakage : Replace )

TRANSFER CASE (PART TIME 4408) 5D1-3
Cannot Front Wheel Drive when Shifted 4H,4L
DIAGNOSIS
Electric Shift Problems
Action
Overhaul and check, replace if necessary.
Overhaul and check for wear and damage.
Replace if necessary.
Check sliding parts, replace if necessary. Checks
Faulty or Damaged TCCU, Speed Sensor, Motor, Clutch
or Internal Wirings
Damaged or Worn Shift Cam, Hub, Fork and Rail Shift
Binding Shift Fork, Hub Collar or Gear
Checks
Broken Drive ChainAction
Check sliding parts, replace if necessary.
Noise in 4WD Operation
Checks
Improper or low oil
Loosened bolts or mounted parts
Noisy T/C bearing
Noisy gearsAction
Drain and replace with specified oil.
Retighten as specified.
Disassemble bearings and parts and check for wear or
damage. Replace if necessary.
Check for wear and damage including speedometer
gear, replace if necessary.
Noise in 4H or 4L
Checks
Worn or Damaged Sprockets or Drive Chain
Incorrect Tire PressureAction
Disassemble and check for wear and damage, replace
if necessary.
Adjust tire pressure.
Transfer Case Oil Leakage
Action
Replace the case.
Clean case and parts and check for leakage.
Remove breather hose and clean, replace if necessary.
Use specified oil and adjust oil level.
Retighten
Use specified sealant and retighten.
Replace Checks
Cracked Transfer Case
Leakage from Other Parts
Breather Clogging
Improper or too much Oil
Loosened Sealing Bolts
Improperly Applied Sealant
Worn or Damaged Oil Seal

9B-10 LIGHTING SYSTEM
Head Lamp Focusing
When using the beam setting device
1. The head lamp focus should be adjusted by using a proper
beam setting device.
2. Adjust the head lamp focus by using Up/Down, Left/Right
adjusting screws.
When using the screen
1. Put the vehicle on the leveling surface.
2. One person is needed to seat on the driver's seat without
other loads(CVW) and check the tire pressure if it is in the
specification.
3. The distance between the headlamp and the screen is 25m.
4. Draw the vertical line (crossing the center of each headlamp)
on the screen.
5. Start the engine.
6. Check if the cut-off line of the headlamp on the screen is in
the specification.
1) Left/right direction
- The degree of the cross point at the cut-off line of the
headlamp and the vertical line should be 15.
2 ) Up/down direction
- The distance between the cut-off line of the headlamp
and the horizontal line should be 25cm.
7. Adjust the focus if the cut-off line of the headlamp is out of
the specification by using up/down, left/right adjusting
screws.
A : Up/down direction adjusting screw
B : Left/right direction adjusting secrw