1998 SSANGYONG MUSSO filler

M162 ENGINE MECHANICAL 1B1-73
Installation Procedure
1. Connect the thrust pin (6) and the snap ring (5) to the chain
tensioner housing (7).
Notice
When connecting the thrust pin, push in the thrust pin far
enough so that it doesn’t protrude at the chain tensioner
housing. 4. Carefully unscrew the screw plug (1), and remove the seal
(2).
Notice
lFor the removal of screw plug, be careful that it can be
jumped out due to the force of compression spring.
lRemove the screw plug only when the seal and
compression spring are damaged.
5. Carefully remove the filler pin (3), compression spring (4),
snap ring (5), and the thrust pin (6).
6. Remove the chain tensioner housing (7) and the seal (8).
3. Insert the compression spring (4) with the filler pin (3) into
chain tensioner housing. 2. Install the chain tensioner housing (7), thrust pin (6), snap
ring (5), and the seal (8).
Installation Notice
Tightening Torque 35 - 40 Nm

1B1-74 M162 ENGINE MECHANICAL
4. Lightly apply the grease to the seal (2) and install the screw
plug (1).
Installation Notice
Sectional View
1 Screw Plug
2 Ball (Nonreturn Valve)
3 Compression Spring
4 Ball Guide
5 Seal (Aluminum)
6 Filler Pin
7 Compression Spring
8 Snap Ring
9 Thrust Pin
10 Ball (Nonreturn Valve)
11 Compression Spring
12 Thrust Piece13 Chain Tensioner Housing
1 4 Seal
15 Timing Gear Case Cover
16 Cylinder Head
17 Bolt / Washer
18 Tensioning Rail
19 Cylinder Head Gasket
20 Timing Chain
21 Tensioning Rail Base (Sliding Surface)
A Oil Supply Hole
B Chain Tensioner Oil Storage Hole 5. Check for leaks by operating the engine.
Tightening Torque 40 Nm

1B1-92 M162 ENGINE MECHANICAL
ENGINE OIL SPECIFICATION
1 Drain Plug................................................. 25 Nm
2 Oil Filter3 Engine Oil Filler Cap
4 Dipstick Gauge
Specifications
Application
CapacityDescrition
Min : 6.7L, Max : 8.2L
lAPI SH or above grade
lACEA : A2 or A3
lApproved oil by MB Sheet 229.1
lApproved oil by MB Sheet 224.1
l Initial at 1000-1500km, Replace every 15000km
Quality
Viscosity
Replacemant

M162 ENGINE MECHANICAL 1B1-95
ENGINE OIL AND OIL FILTER ELEMENT
4. Remove the drain plug (arrow) and drain the engine oil.
Notice
Leave the oil filler cap open to ease the engine oil discharge.
5. Tighten the engine oil drain plug after cleaning it.
Installation Notice Tools Required
103 589 02 09 00 Oil Filter Socket Wrench
Replacement Procedure
1. Install the socket wrench”7” (special tool : 103 589 02 09
00) on the oil filter cover (2).
Notice
Make the screw cover removable by tightening the bolt at
the side of the socket wrench (special tool).
2. Install the wrench to the upper bolt in the socket wrench
and remove the oil cover by turning it.
3. Remove the oil filter element.
Notice
Work with a cloth under the vehicle when removing the oil
filter element to not drain the oil.
Replace the seal washer with new one.
6. Replace the O-ring(5) in the oil filter cover with new one.
Notice
Apply the engine oil to the O-ring.
7. Insert new oil filter element into the oil filter housing.
Tightening Torque 25 Nm
8. Temporarily tighten the oil filter cover (2). Install the socket
wrench “7” (special tool : 103 589 02 09 00), and then
completely tighten it.
Installation Notice
2 Oil Filter Cover
5 O-ring
6 Oil Filter Element
7 Special Tool (Socket Wrench)
Tightening Torque 25 Nm

1B1-96 M162 ENGINE MECHANICAL
3 Oil Filler Cap
4 Dipstick Gauge
9. Fill up engine oil through the engine oil filler opening (3).
10. Check for oil leaks at normal engine temperature after
starting the engine.
11. Stop the engine and wait 5 minutes.
Check the oil level and fill up as specified if necessary.

M161 ENGINE MECHANICAL 1B2-77
CHAIN TENSIONER
1 Screw Plug................................................ 40 Nm
2 Seal
3 Filler Pin
4 Compression Spring5 Snap Ring
6 Thrust Pin
7 Chain Tensioner Housing.....................72-88 Nm
8 Seal
Removal Procedure
1. Position the number 1 cylinder to ATDC 20°.
Notice
Remove the oil filler cap at adjustment position, and check
whether the intake camshaft cam’s lobe (arrow) stays in the
upper side.
2. Cover the alternator with a clean cloth.
3. Release the tension by unscrewing the screw plug once.
Notice
In case that the tension is reduced by unscrewing the screw
plug, reinstall after completely removing the chain tensioner.
If the chain tensioner is tightened again without completely
reducing its tension, then the snap ring doesn’t return to
the original position and the tension gets excedded.

1B2-78 M161 ENGINE MECHANICAL
Installation Procedure
1. Connect the thrust pin (6) and the snap ring (5) to the chain
tensioner housing (7).
Notice
When connecting the thrust pin, push in the thrust pin far
enough so that it doesn’t protrude at the chain tensioner
housing. 4. Carefully unscrew the screw plug (1), and remove the seal
(2).
Notice
lFor the removal of screw plug, be careful that it can be
jumped out due to the force of compression spring.
lRemove the screw plug only when the seal and
compression spring are damaged.
5. Carefully remove the filler pin (3), compression spring (4),
snap ring (5), and the thrust pin (6).
6. Remove the chain tensioner housing (7) and the seal (8).
3. Insert the compression spring (4) with the filler pin (3) into
chain tensioner housing. 2. Install the chain tensioner housing (7), Thrust pin (6), snap
ring (5), and the seal (8).
Installation Notice
Tightening Torque 72 - 88 Nm

M161 ENGINE MECHANICAL 1B2-79
4. Lightly apply the grease to the seal (2) and install the screw
plug (1).
Installation Notice
Sectional View
1 Screw Plug
2 Ball (Nonreturn Valve)
3 Compression Spring
4 Ball Guide
5 Seal (Aluminum)
6 Filler Pin
7 Compression Spring
8 Snap Ring
9 Thrust Pin
10 Ball (Nonreturn Valve)
11 Compression Spring
12 Thrust Piece13 Chain Tensioner Housing
1 4 Seal
15 Timing Gear Case Cover
16 Cylinder Head
17 Bolt / Washer
18 Tensioning Rail
19 Cylinder Head Gasket
20 Timing Chain
21 Tensioning Rail Base (Sliding Surface)
A Oil Supply Hole
B Chain Tensioner Oil Storage Hole 5. Check for leaks by operating the engine.
Tightening Torque 40 Nm