1998 SSANGYONG MUSSO filler

1B2-100 M161 ENGINE MECHANICAL
9. Fill up engine oil through the engine oil filler opening.
10. Check for oil leaks at normal engine temperature after
starting the engine.
11. Stop the engine and wait 5 minutes.
Check the oil level and fill up as specified if necessary. 4. Remove the drain plug (1) and drain the engine oil.
Notice
Leave the oil filler cap (3) open to ease the engine oil
discharge.
5. Tighten the engine oil drain plug after cleaning it.
Installation Notice Tools Required
103 589 02 09 00 Oil Filter Socket Wrench
Replacement Procedure
1. Install the socket wrench”7” (special tool : 103 589 02 09
00) on the oil filter cover (2).
Notice
Make the screw cover removable by tightening the bolt at
the side of the socket wrench (special tool).
2. Install the wrench to the upper bolt in the socket wrench
and remove the oil cover by turning it.
3. Remove the oil filter element.
Notice
Work with a cloth under the vehicle when removing the oil
filter element to not drain the oil.
Replace the seal washer with new one.
6. Replace the O-ring(5) in the oil filter cover with new one.
Notice
Apply the engine oil to the O-ring.
7. Insert new oil filter element into the oil filter housing.
Tightening Torque 25 Nm
8. Temporarily tighten the oil filter cover (2). Install the socket
wrench “7” (special tool : 103 589 02 09 00), and then
completely tighten it.
Installation Notice
2 Oil Filter Cover
5 O-ring
6 Oil Filter Element
7 Special Tool (Socket Wrench)
Tightening Torque 25 Nm

1B3-146 OM600 ENGINE MECHANICAL
Notice
Always install the chain tensioner to be filled with oil.
Place the chain tensioner in engine oil up to over the collar on the hexagon head with the thrust pin facing up.
Slowly push down the thrust pin as far as the stop 7~10 times with the aid of a press or a column drill
Faulty chain tensioners should be replaced completely.
3 Screw Plug
4 Aluminum Gasket
5 Ball
6 Ball Guide
7 Compression Spring
8 Compression Spring
9 Housing
10 Thrust Pin11 Valve Disc
12 O-Ring
13 Snap Ring
14 Compression Spring
15 Filler
A Feed Bore from Cylinder Head
B To Oil Pan

1D1-4 M162 ENGINE COOLING
DIAGNOSIS
3. Connect the special tool to the reservoir filler cap and apply
1.4 bar of pressure.
SYSTEM LEAKAGE TEST
Tools Required
124 589 15 21 00 Tester
Test Procedure
1. Loosen the cap a little and release pressure and remove
the cap.
Notice
For the risk of scalding, cap must not be opened unless the
coolant temperature is below 90°C.
2. Fill coolant up to upper edge (arrow) of reservoir.
Tester 124 589 15 21 00
4. If the pressure on the tester drops, check leakage at the all
coolant hoses and pipes and each connections. Replace
or retighten if necessary.

1D2-4 M161 ENGINE COOLING
DIAGNOSIS
3. Connect the special tool to the reservoir filler cap and apply
1.4 bar of pressure.
SYSTEM LEAKAGE TEST
Tools Required
124 589 15 21 00 Tester
Test Procedure
1. Loosen the cap a little and release pressure and remove
the cap.
Notice
For the risk of scalding, cap must not be opened unless the
coolant temperature is below 90°C.
2. Fill coolant up to upper edge (arrow) of reservoir.
Tester 124 589 15 21 00
4. If the pressure on the tester drops, check leakage at the all
coolant hoses and pipes and each connections. Replace
or retighten if necessary.

1F3-4 OM600 ENGINE CONTROLS
FUEL TANK
1 Fuel Tank
2 The Sender of Fuel Tank
3 2-way Check Valve
4 Pre Filter
5 Front Fuel Filler Neck
6 Rear Fuel Filler Neck
7 Fuel Supply Tube8 Fuel Return Tube
9 Filter Hose
10 Fuel Tank Hose
11 Fuel Filler Cap
1 2 Clip
1 3 Clip

FRONT DRIVE AXLE 3A-17
1 Front Axle Housing Mounting Bracket
2 Inner Shaft (Left)
3 Bolt......................................................55-65 Nm
4 Oil Seal.................................................. Replace
Apply Grease to the Sealing Rib
5 Snap Ring
6 Bearing
7 Snap Ring
8 Oil Drain Plug.......................................28-41 Nm
9 Front Axle Housing
10 Breather Nipple
11 Inner Shaft (Right)
12 Pinion Lock Nut................................240-310 Nm
13 Washer
14 Companion Flange
15 Oil Seal.................................................. Replace
Apply Grease to the Sealing Rib
16 Bearing
1 7 Shim
18 Bearing Baffle
1 9 Shim20 Bearing
21 Oil Slinger
22 Drive Pinion
23 Oil Filler Plug.......................................28-41 Nm
2 4 Bolt......................................................39-46 Nm
25 Axle Housing Cover..............Apply Liquid Gasket
to the Contact Surface
26 Ring Gear
27 Bearing
2 8 Shim
29 Shaft Lock Pin
30 Differential Case
3 1 Bolt......................................................75-90 Nm
3 2 Bolt......................................................48-69 Nm
33 Washer
34 Bearing Cap
35 Thrust Washer
36 Side Gear
37 Differential Shaft
38 Differential Pinion
39 Thrust Washer

3D-2 REAR DRIVE AXLE
FASTENER TIGHTENING SPECIFICATIONS
Application
Inner Bracket Mounting Nut
Propeller Shaft to Rear Axle Input Shaft
Lower Arm Mounting Nut
Lower Shock Absorber to Axle Housing
Upper Arm Mounting Nut
Stabilizer Bar Mounting Bolt
Lateral Rod Mounting Nut
Drive Pinion Lock Nut
Oil Drain Plug
Ring Gear Mounting Bolt
Oil Filler PlugN
· ·· ·
·m
50 - 65
70 - 80
150 - 180
50 - 65
150 - 180
30 - 45
150 - 180
240 - 310
28 - 42
75 - 90
28 - 42
4.55
4.55
4.55
4.27
5.86
3.73
3.73
4.89
1.9 L
SEA 80W/90, API GL - 5 M/T
A/T (MB)
M/T
A/T (MB)
A/T (BTRA)
M/T
A/T (MB)
A/T (BTRA)
Oil Capacity
Oil Specification
ApplicationDescription
GENERAL SPECIFICATIONS(CONT'D)
E20
E23
E32 Reduction Ratio

REAR DRIVE AXLE 3D-11
UNIT REPAIR
AXLE HOUSING
Preceding Work : Removal of the axle shaft
Removal of the axle housing
1 Drive Pinion Lock Nut......................240-310 Nm
2 Washer
3 Companion Flange
4 Pinion Oil Seal
5 Bearing Slinger
6 Bearing
7 Shim
8 Shim
9 Bearing Cup
10 Breather Nipple
11 Rear Axle Housing
12 Oil Drain Plug.......................................28-42 Nm
1 3 Shim
14 Bearing
15 Drive Pinion
16 Bearing Cap1 7 Bolt....................................................87-124 Nm
18 Bearing
1 9 Shim
20 Ring Gear
21 Shaft Lock Pin
22 Differential Case
23 Ring Gear Mounting Bolt......................75-90 Nm
24 Thrust Washer
25 Differential Pinion
26 Thrust Washer
27 Side Gear
28 Differential Shaft
29 Housing Cover
3 0 Bolt......................................................38-46 Nm
31 Oil Filler Plug.......................................28-42 Nm