1998 SSANGYONG MUSSO ECU

M161 ENGINE MECHANICAL 1B2-67
Tools Required
000 589 01 10 00 Box Wrench Insert
104 589 01 01 00Spanner
Removal & Installation Procedure
1. Turn the crankshaft and position the no.1 cylinder piston at
ATDC20°.
2. Put the alignment marks (arrows) on the camshaft sprocket
and the timing chain.
3. Remove the chain tensioner.
Installation Notice
Tightening Torque40 Nm
72 - 88 Nm
Screw Plug
Tensioner Assembly
4. Remove the exhoust camshaft sprocket.
Installation Notice
Tightening Torque1st step 35 - 45 Nm
2nd step 85° - 95°
Notice
The sprocket bolt is designed to be used only once, so
always replace with new one.
5. Take off the timing chain from intake camshaft sprocket,
and secute it not to fall down into the timing gear case.
6. Using the wrench (7), turn the camshaft until there is no
resistence in camshaft bearing area.

1B2-74 M161 ENGINE MECHANICAL
8. Install the lever pusher (11) and the thrust piece (8) to the
slide (9).
13. Remove the valve cotter (2) using either the pincette (13)
or magnetic finger.
Lever Pusher 111 589 18 61 00
Magnetic Finger 116 589 06 63 00
9. Mount the thrust piece (8) vertically to the valve spring
retainer (3).
10. Make the thrust piece (8) and the slide (9) perpendicular
to each other.
11. Secure the slide (9) by turning the adjust bolt (10).
12. Press the valve spring (4) by using the lever pusher (11).
14. Remove the upper retainer (3) and the valve spring (4).
15. Remove the valve stem seal and replace if necessary.
Notice
Check the valve stem seal and replace if necessary.
16. Remove the lower retainer (6).
Notice
Check the retainer for damages and replace with a new
one if necessary.
17. Installation should follow the removal procedure in the
reverse order.

M162 ENGINE ELECTRICAL 1E1-11
Circuit Diagram
Inspection & Maintenance Procedure (for MSE)
1. While the ignition switch is in 'OFF' position, remove the
wiring connectors (1 and 15) from ignition coil and measure
the primary resistance between terminal No.1 and No.15.
2. During engine cranking, measure primary voltage (T1/1)
between ECU terminal No. 71 and No. 69. Notice
If out of specified value, replace the ignition coil.
Specified Value 0.9 - 1.6 W (20°C)
Specified Value 200 - 350 V
Notice
lMeasure remaining cables.
- T1/2 : No. 72 and 69.
- T1/3 : No. 70 and 69.
lIf out of specified value, check ignition cable and ECU.
3. Using a multi-tester, measure the secondary coil resistance
between 5a and 5b.
Specified Value 6 - 8.5 kW

M161 ENGINE ELECTRICAL 1E2-11
Inspection & Maintenance (for E2.3 MSE)
1. Measure the primary resistance between the cable terminals
1 and 15 after removing the ignition cable wiring connector
(1 and 15) with ignition switch OFF.
Notice
Replace the ignition coil if out of the specified resistance.
lT1/2 : between No.71 and No.69
Notice
Check the ignition cable and the ECU if out of the
specified value.
3. Measure the secondary cable resistance between the
ignition coil 5a and 5b using a multimeter. 2. Measure the primary voltage(T1/1) between the ECU
terminals No.72 and No.69 during the engine cranking
(starter motor activated).
Specified Value 6 - 8.5 KW
Specified Value 0.9 - 1.6 W
Specified Value 200 - 350 V

SECTION 1F1
M162 ENGINE CONTROLS
TABLE OF CONTENTS
CAUTION: Disconnect the negative battery cable before removing or installing any electrical unit or when a
tool or equipment could easily come in contact with exposed electrical terminals. Disconnecting this cable
will help prevent personal injury and damage to the vehicle. The ignition must also be in LOCK unless otherwise
noted.
Specifications . . . . . . . . . . . . . . . . . . . . . . . 1F1-2
Fastener Tightening Specifications . . . . . . . . 1F1-2
Special Tools . . . . . . . . . . . . . . . . . . . . . . . 1F1-3
Special Tools Table . . . . . . . . . . . . . . . . . . . . 1F1-3
Schematic and Routing Diagrams . . . . . . . 1F1-4
E32 ECU (HFM) . . . . . . . . . . . . . . . . . . . . . . 1F1-4
E32 ECU (MSE) . . . . . . . . . . . . . . . . . . . . . . 1F1-5
Diagnosis . . . . . . . . . . . . . . . . . . . . . . . . . . 1F1-6
Self Diagnosis Socket Pin Numbers and
Descriptions . . . . . . . . . . . . . . . . . . . . . . . . 1F1-6
Self Diagnosis Failure Code . . . . . . . . . . . . . 1F1-7
Test Box Connection . . . . . . . . . . . . . . . . . . 1F1-10
Fuel Injection System Test (MSE3.62) . . . . . 1F1-11
Ignition System Test . . . . . . . . . . . . . . . . . . 1F1-21
Idling Control and Electronic Pedal
System Test . . . . . . . . . . . . . . . . . . . . . . . 1F1-26
Air Conditioner Control System Test . . . . . . 1F1-28
Fuel Pressure and Internal Leakage Test . . 1F1-29
Fuel Pump Test . . . . . . . . . . . . . . . . . . . . . . 1F1-31Injector Test . . . . . . . . . . . . . . . . . . . . . . . . 1F1-33
Maintenance and Repair . . . . . . . . . . . . . 1F1-35
On-Vehicle Service . . . . . . . . . . . . . . . . . . . . 1F1-35
ECU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1F1-35
Fuel Pressure Regulator . . . . . . . . . . . . . . 1F1-46
Fuel Distributor . . . . . . . . . . . . . . . . . . . . . . 1F1-50
Injector . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1F1-54
Fuel Filter . . . . . . . . . . . . . . . . . . . . . . . . . . 1F1-57
Fuel Pump . . . . . . . . . . . . . . . . . . . . . . . . . 1F1-58
Purge Switchover Valve . . . . . . . . . . . . . . . 1F1-62
Vacuum System . . . . . . . . . . . . . . . . . . . . . 1F1-64
Crankshaft Position Sensor . . . . . . . . . . . . 1F1-65
Camshaft Position Sensor . . . . . . . . . . . . . 1F1-67
Hot Film Air Mass (HFM) Sensor . . . . . . . . . 1F1-69
Oxygen Sensor . . . . . . . . . . . . . . . . . . . . . . 1F1-72
Knock Sensor . . . . . . . . . . . . . . . . . . . . . . . 1F1-74
Coolant Temperature Sensor . . . . . . . . . . . 1F1-75
Accelerator Pedal Module . . . . . . . . . . . . . . 1F1-78

M162 ENGINE CONTROLS 1F1-3
SPECIAL TOOLS
SPECIAL TOOLS TABLE
129 589 00 21 00
Test Box
119 589 04 63 00
Pressure Hose
106 589 00 21 00
Pressure Tester
210 589 08 63 00
ECU Test Cable210201Adaptor line

1F1-4 M162 ENGINE CONTROLS
E32 ECU (HFM)
SCHEMATIC AND ROUTING DIAGRAMS

M162 ENGINE CONTROLS 1F1-5
E32 ECU (MSE)