1998 SSANGYONG MUSSO wiring

BODY WIRING SYSTEM 9A-23
MANUAL TRANSMISSION
1 Main Wiring Connector......................Diesel E/G
2 Main Wiring Connector..................Gasoline E/G
3 Main Wiring Connector.........................Gasoline
(E32, E23) E/G
4 Back Up Switch5 Oil Pressure Switch
6 Start Motor Solenoid
7 Micro Switch
8 Speed Sensor (Turbo Diesel Engine Only)

9A-24 BODY WIRING SYSTEM
AUTOMATIC TRANSMISSION (BENZ)
1 Main Wiring Connector
2 Start Lock Switch
3 Automatic Transmission Change Over Valve
4 Transmission Overload
Protection Switch...........................Gasoline E/G5 Oil Pressure Switch
6 Start Solenoid
7 Micro Switch.......................................Diesel E/G
8 Speed Sensor.......................... Turbo Diesel E/G

BODY WIRING SYSTEM 9A-25
AUTOMATIC TRANSMISSION (BTRA)
1 Main Wiring Connector
2 Main Wiring Connector
3 Transmission
4 Transmission Lever
5 Oil Pressure Switch............................Diesel E/G6 Start Motor Solenoid
7 Throttle Position Sensor....................Diesel E/G
8 Speed Sensor.......................... Turbo Diesel E/G
9 Inhibitor Switch

9A-26 BODY WIRING SYSTEM
DRIVER'S SEAT
1 Main Wiring Connector
2 Tilt Motor
3 Heater Control Unit
4 Height Motor5 Slide Motor
6 Back Seat Wiring Connector
7 Seat Heater
8 Driver Seat Switch

DOORS 9P-5
TAIL GATE
Removal & Installation Procedure
1. Remove the shock absorber mounting bolts.
2. Disconnect the tailgate wiring harness.
3. Remove the tailgate by removing the tailgate bracket bolts.
4. Installation should follow the removal procedure in the
reverse order.

REMOTE KEYLESS ENTRY AND ANTI-THEFT SYSTEM 9T-5
MAINTENANCE AND REPAIR
ON-VEHICLE SERVICE
REKES
1 REKES Receiver
2 Antenna3 Bolt
4 Wiring Connector (6P)

9T-6 REMOTE KEYLESS ENTRY AND ANTI-THEFT SYSTEM
Input Memory
lWhen the REKES transmitter is lost
1. Connect the battery terminal No.3 and REKES terminal No.4
which are on the diagnosis socket in engine room with service
lead wire.
2. Push the lock or unlock button on the REKES transmitter.
3. Input Memory and close all doors.
4. Check the operation of door locking system by pushing the
lock or unlock button on the REKES transmitter.
lWhen the transmitter is faulty
1. Replace the REKES transmitter with a new one and connect
the wiring connector.
2. Set the input switch of the REKES receiver onto the No.1 or
No.2 position and push the lock or unlock button on the
REKES transmitter.
3. Set the input switch of the REKES receiver onto the central
position and close all doors.
4. Check the operation of door locking system by pushing the
lock or unlock button on the REKES transmitter.
1 REKES Transmitter
2 Input Switch of the REKES Receive
3 REKES Switch

9W-8 IMMOBILIZER SYSTEM
DefectsPossible cause Remedy
No communication with
transponder1. Defective wiring harness
- Power supply/Open/short of ground
- Open/short of signal terminal or
mis-conneting(between ECU
terminal No. 13 and 14)1. Connect/replace the wire correctly.
2.1 Replace the transponder
2.2 Immobilizer programming 2. Damaged transponder
3. Replace the antenna3. Defective antenna
4.1 Replace the ECU
4.2 Replace all transponder of the keys
4.3 Immobilizer programming 4. Defective ECU
No immobilizer
programming
(Components and
wiring harnesses are
normal but codes in
ECU and transponders
are not registered
normally)1. Replace the transponders and ECU
with new
; Immobilizer programming is not
performed1. Perform immobilizer programming
2. Replace transponders only(new)
; Immobilizer programming is not
performed2. Perform immobilizer programming
3. Replace ECU only(new) 3.1 Replace the transponders with new
3.2 Perform immobilizer programming
4. Replace the transponder only
; Programmed for other ECU4.1 Replace the transponders with new
4.2 Perform immobilizer programming
5. Re-programming is not performed
after clearing transponder code stored
in ECU that normally used system5. Immobilizer programming
Notice
1. Application of ex-programmed transponder into other ECUs.
; In this case, it can not be removed for the settled “lock bit” in transponder even though you perform immobilizer
problem normally. Moreover it is impossible to start engine, so replace the transponder with new and perform
immobilizer programming.
DIAGNOSIS
GASOLINE ENGINE
Cause and Remedy for Defective When Diagnosed by Scanner