1998 OPEL FRONTERA transmission

MANUAL TRANSMISSION7B–69
Torque Specifications
E07RW049

7B–70MANUAL TRANSMISSION
Torque Specifications (Cont’d)
E07RW050

MANUAL TRANSMISSION7B–71
Torque Specifications (Cont’d)
E07RW051

7B–72MANUAL TRANSMISSION
Special Tools
ILLUSTRATIONTOOL NO.
TOOL NAME
5–8840–2550–0
(J–42794)
Gear spline pieace
remover
5–8840–2551–0
(J–42795)
Center bearing remover
5–8840–2560–0
(J–42988)
Attachment
5–8840–2552–0
(J–42796)
Counter gear shaft
center bearing installer
5–8840–2553–0
(J–42797)
Clutch hub (No.2)
installer
5–8840–2554–0
(J–42798)
Clutch hub (No.1)
installer
ILLUSTRATIONTOOL NO.
TOOL NAME
5–8840–2555–0
(J–42799)
Installer
5–8840–2556–0
(J–42800)
Counter gear shaft front
bearing installer
5–8840–2559–0
(J–42904)
Top gear shaft front
bearing installer
5–8840–2557–0
(J–42801)
Front rerainer oil seal
installer
5–8840–2558–0
(J–42802)
Transfer adapter oil seal
installer
5–8840–0007–0
(J–8092)
Driver handle

MANUAL TRANSMISSION7B–73
Special Tools (Cont’d)
ILLUSTRATIONTOOL NO.
TOOL NAME
5–8840–0015–0
(J–22912–01)
Bearing separator

CLUTCH7C–1
TRANSMISSION
CLUTCH
CONTENTS
Service Precaution 7C–1. . . . . . . . . . . . . . . . . . . . . .
General Description 7C–2. . . . . . . . . . . . . . . . . . . . .
Diagnosis 7C–8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Clutch Assembly 7C–9. . . . . . . . . . . . . . . . . . . . . . . .
Clutch Assembly and Associated Parts 7C–9. . .
Removal 7C–9. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Inspection and Repair 7C–10. . . . . . . . . . . . . . . . . .
Installation 7C–15. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Clutch Control 7C–17. . . . . . . . . . . . . . . . . . . . . . . . . .
Clutch Control Parts 7C–17. . . . . . . . . . . . . . . . . . .
Removal 7C–18. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Inspection and Repair 7C–18. . . . . . . . . . . . . . . . . .
Installation 7C–19. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Adjustment 7C–19. . . . . . . . . . . . . . . . . . . . . . . . . . .
Master Cylinder 7C–22. . . . . . . . . . . . . . . . . . . . . . . . .
Disassembled View 7C–22. . . . . . . . . . . . . . . . . . . .
Disassembly 7C–23. . . . . . . . . . . . . . . . . . . . . . . . . . Inspection and Repair 7C–23. . . . . . . . . . . . . . . . . .
Reassembly 7C–23. . . . . . . . . . . . . . . . . . . . . . . . . .
Slave Cylinder 7C–24. . . . . . . . . . . . . . . . . . . . . . . . . .
Disassembled View 7C–24. . . . . . . . . . . . . . . . . . . .
Disassembly 7C–24. . . . . . . . . . . . . . . . . . . . . . . . . .
Inspection and Repair 7C–24. . . . . . . . . . . . . . . . . .
Reassembly 7C–25. . . . . . . . . . . . . . . . . . . . . . . . . .
Damper Cylinder 7C–26. . . . . . . . . . . . . . . . . . . . . . . .
Disassembled View 7C–26. . . . . . . . . . . . . . . . . . . .
Disassembly 7C–26. . . . . . . . . . . . . . . . . . . . . . . . . .
Inspection and Repair 7C–26. . . . . . . . . . . . . . . . . .
Reassembly 7C–26. . . . . . . . . . . . . . . . . . . . . . . . . .
Main Data and Specifications 7C–27. . . . . . . . . . . . .
General Specifications 7C–27. . . . . . . . . . . . . . . . .
Torque Specifications 7C–27. . . . . . . . . . . . . . . . . .
Special Tools 7C–30. . . . . . . . . . . . . . . . . . . . . . . . . . .
Service Precaution
WARNING: IF SO EQUIPPED WITH A
SUPPLEMENTAL RESTRAINT SYSTEM (SRS),
REFER TO THE SRS COMPONENT AND WIRING
LOCATION VIEW IN ORDER TO DETERMINE
WHETHER YOU ARE PERFORMING SERVICE ON OR
NEAR THE SRS COMPONENTS OR THE SRS
WIRING. WHEN YOU ARE PERFOMING SERVICE ON
OR NEAR THE SRS COMPONENTS OR THE SRS
WIRING, REFER TO THE SRS SERVICE
INFORMATION. FAILURE TO FOLLOW WARNINGS
COULD RESULT IN POSSIBLE AIR BAG
DEPLOYMENT, PERSONAL INJURY, OR
OTHERWISE UNNEEDED SRS SYSTEM REPAIRS. CAUTION: Always use the correct fastner in the
proper location. When you reolace a fastener, use
ONLY the exact part number for that application.
ISUZU will call out those fasteners that requir a
replacement after removal. ISUZU will also call out
the fasteners that requir thread lockers or thread
sealant. UNLESS OTHERWISE SPECIFIED , do not
use supplemental coatings (Paints, greases, or other
corrosion inhibitors) on threaded fastners or fastner
joint interfaces. Generally,such coatings adversely
affect the fastner torque and the joint clamping force,
and may damage the fastner. When you install
fasteners, use the correct tightening sequence and
specifications. Following these instructions can
help you avoid damage to parts and systems.

CLUTCH7C–9
Clutch Assembly
Clutch Assembly and Associated Parts
201RW029
Legend
(1) Flywheel Assembly and Crankshaft Bearing
(2) Driven Plate Assembly (6VE1)
(3) Driven Plate Assembly (4JX1)
(4) Pressure Plate Assembly (5) Transmission Assembly
(6) Front Cover
(7) Shift Fork
(8) Release Bearing
Removal
1. Remove transmission assembly, refer to ”MANUAL
TRANSMISSION” of Section 7B for ”Removal AND
INSTALLATION” procedure.
2. Mark the flywheel, clutch cover and pressure plate lug
for alignment when installing.
3. Remove pressure plate assembly (3).
4. Remove driven plate assembly (1) or (2). Use the pilot
aligner 5-85253-001-0 (J-24547) to prevent the
driven plate assembly from falling free.
201RW031

7C–10CLUTCH
5. Mark the flywheel, clutch cover and pressure plate lug
for alignment when installing.
6. Remove the release bearing (3) from the
transmission case .
7. Remove the shift fork snap pin.
8. Remove the shift fork pin and shift fork (4) from the
front cover.
9. Remove the front cover bolts.
10. Remove the front cover (5) from the transmission
case.
220RW088
11. Remove flywheel assembly and crankshaft bearing.
Do not remove except for replacement.
12. Use the remover 5–8840–2000–0 (J–5822) and
sliding hammer 5–8840–0019–0 (J–23907) to
remove the crankshaft bearing
015RW053
Inspection and Repair
Make necessary correction or parts replacement if wear,
damage, or any other abnormal condition are found
through inspection.
Pressure Plate Assembly
201RS002
1. Visually check the pressure plate friction surface for
excessive wear and heat cracks.
2. If excessive wear or deep heat cracks are present,
the pressure plate must be replaced.
Pressure Plate Warpage
201RS003