1998 OPEL FRONTERA clutch

7C–24CLUTCH
Slave Cylinder
Disassembled View
206RW004
Legend
(1) Cylinder Body
(2) Spring(3) Piston and Piston Cup
(4) Boot
(5) Push Rod
Disassembly
1. Remove boot.
2. Remove push rod.
3. Remove piston and piston cup.
4. Remove spring.
Inspection and Repair
Make the necessary adjustments, repairs, and part
replacements if excessive wear or damage is discovered
during inspection.
Cylinder Body
206RS003
1. Clean the cylinder body.
2. Check the fluid return port for restrictions and clean it
if necessary.

CLUTCH7C–25
Piston and Piston Cup
1. Visually inspect the disassembled piston and piston
cup for excessive wear and damage.
2. Replace the inner parts with new parts shown in the
illustration.
206RS004
3. Measure the clearance between slave cylinder wall
and piston.
4. If the measured value exceeds the specified limit, the
slave cylinder assembly must be replaced.
Standard: 0.07 mm (0.0028 in)
Limit: 0.15 mm (0.0059 in)
206RS005
Reassembly
To reassemble, follow the disassembly steps in the
reverse order, noting the following points:
1. Before installing the parts, apply a thin coat of rubber
grease.
2. Install cup in groove in piston with the lip turned to the
front of cylinder. Use care so as not to scratch the
cylinder.
206RS006

7C–26CLUTCH
Damper Cylinder
Disassembled View
205RW005
Legend
(1) Cylinder Body
(2) Spring
(3) Piston Assembly(4) Spacer
(5) Damper Rubber
(6) Cover and Gasket
Disassembly
1. Remove cover and gasket.
2. Remove damper rubber.
3. Remove spacer.
4. Remove piston assembly.
5. Remove spring.
Inspection and Repair
Check damper rubber and piston cup for cracks,
deformation or damage.
Replace the damper cylinder assembly if necessary.
Reassembly
To assemble, follow the disassembly steps in the reverse
order.

CLUTCH7C–27
Main Data and Specifications
General Specifications
Ty p eDry single plate type with diaphragm spring
Size275 mm (10.83 in)
Pressure plate Outside diameter332 mm (13.07 in)
Pressure plate Clamping force7208 N (1621 lb)
Pressure plate Spring finger height49.9–51.9mm(1.965–2.043in)
Driven plate Outside diameter x inside diameter275180 mm (10.836.69 in)
Thickness Clutch disengaged8.8 mm (0.346 in)
Thickness Clutch engaged8.3 mm (0.327 in)
Total friction area 3392cm(522in)
Clutch control type Hydraulic
Clutch pedal free play 5 – 15 mm (0.20 – 0.59 in)
Clutch pedal heightLHD: 217 – 227 mm (8.543 – 8.937 in)
RHD:
(6VE1) 238.5 mm – 248.5 mm (9.390 in – 9.783 in)
(4JX1) 231 mm – 241 mm (9.094 in – 9.488 in)
Clutch pedal stroke 152.5 – 162.5 mm (6.004 – 6.398 in)
4JX1, RHD: 145 – 155mm (5.709 – 6.102 in)
Torque Specifications
E07RW053

7C–28CLUTCH
Torque Specifications (Cont’d)
(6VE1 LHD)
E07RW054

CLUTCH7C–29
Torque Specifications (Cont’d)
(Except 6VE1 LHD)
E07RW055

7C–30CLUTCH
Special Tools
ILLUSTRATIONTOOL NO.
TOOL NAME
5-85253-001-0
(J-24547)
Driven plate aligner
5-8840-2000-0 and
5-8840-0019-0
(J-5822 and J-23907)
Pilot bearing remover
and Sliding hammer
5-8840-0125-0
(J-26516-A)
Crankshaft pilot bearing
installer
5-8840-0007-0
(J-8092)
Driver handle

3.0
W
3.0
L/R 3.0
L/B
0.5
O/G
AUDIO
CIGARETTE
LIGHTERBLOWER
MOTORMAGNETIC
CLUTCHPOWER
WINDOW
RELAY
(2)STOPLIGHT AUDIO
(14)
DOME LIGHTRR DEFOGGER
FRT DOOR LOCK &
POWER WINDOW SW C-11 10A
AUDIO
(ACC)
MIRROR
0.5
BRC-20 10A
AIR CON
0.85
G/WC-14 15A
STOP
A/T CONT
1.25
R/WC-15 20A
AUDIO (B)
3.0
L/OC-17 25A
RR
DEFOG
FUSE BOX
1.25
O/BC-12 20A
CIGAR
3.0
LC-19 25A
BLOWER
3.0
B/L 3.0
W5.0
W 5.0
W
5.0
W
C/B-2 30A
P/W,P/S,
S/R
0.5
R/WC-16 10A
CLOCK (B)
ROOM
1.25
LG/WC-18 20A
DOOR
LOCK
HEATER &
A/C RELAY
B-36
2
B-364
D08RWB16