1998 OLDSMOBILE BRAVADA Owners Manual

How to Add Coolant to the Radiator
I
1. You can remove the radiator pressure cap when the
cooling system, including the radiator pressure cap
and upper radiator
hose, is no longer hot. Turn the
pressure cap slowly counterclockwise
until it first
stops. (Don't press down while turning the
pressure cap.)
If you hear a hiss, wait for that to stop. A hiss means
there is still
some pressure left.
p :. I
2. Then keep turning the pressure cap, but now push
down
as you turn it. Remove the pressure cap.
ProCarManuals.com

3. Fill the radiator with the proper DEX-COOL@
coolant mixture, LIP to the base of the filler neck.
(See “Engine Coolant‘’
in the Index for more
information about the proper
coolant mixture.)
4. Then fill the coolant recovery tank to the ADD mark.
5. Put the cap back on the coolant recovery tank, but
leave the radiator pressure cap off’.
5-20
ProCarManuals.com

6. Start the engine and let it run until you can feel the
upper radiator hose getting
hot. Watch out for the
engine cooling fan.
7. By this time, the coolant level inside the I-' d' lator
filler neck rnay be lower.
If the level is lower, add
more
of the proper DEX-COOL@ coolant mixture
through the filler neck until the level reaches the
base of the filler neck.
8. Then replace the pressure cap. At any time during
this procedure
if coolant begins to flow out of the
filler neck, reinstall the pressure
cap. Be sure the
arrows
on thti pressure cap line up like this.
5-2 1
ProCarManuals.com

If a Tire Goes Flat
It’s unusual for a tire to “blow out” while you’re driving,
especially if
you maintain your tires properly. If air goes
out of
a tire, it’s much more likely to leak out slowly.
But if you should ever have
a “blowout,” here are a few
tips about what to expect and what to do:
If a front tire fails, the flat tire will create a drag that
pulls the vehicle toward that side. Take your foot off the
accelerator pedal and grip the steering wheel
firmly.
Steer to maintain lane position, and then gently brake to
a stop well out of the traffic lane.
A rear blowout, particularly on a curve, acts much like a
skid and may require the same correction you’d use in a
skid. In any rear blowout, remove your foot from the
accelerator pedal. Get the vehicle under control by
steering the way you want the vehicle to go. It may be
very bumpy and noisy, but you can still steer. Gently
brake to
a stop -- well off the road if possible.
If a tire goes flat, the next part shows how to use your
jacking equipment to change
a flat tire safely.
Changing a Flat Tire
If a tire goes flat, avoid further tire and wheel damage
by driving slowly to
a level place. Turn on your hazard
warning flashers.
Changing a tire can cause an injury. The vehicle
can slip off the jack and roll over you or other
people. You and they could be badly injured.
Find
a level place to change your tire. To help
prevent the vehicle from moving:
1. Set the parking brake firmly.
2. Put the shift lever in PARK (P).
3. nrn off the engine.
To be even more certain the vehicle won’t move,
you can put blocks at the front and rear of the
tire farthest away from the one being changed.
That would be the tire on the other side of the
vehicle, at the opposite end.
The following steps will tell you how to use the jack and
change
a tire.
5-22
ProCarManuals.com

Removing the Spare Tire and Tools
The jacking equipment you’ll need is stored along the
driver’s rear wall. Your vehicle is also equipped with
work gloves and a plastic ground mat
to assist in the
changing
of a flat tire.
To remove the jack cover,
pull up on the latch(es) on
the cover, Remove the
wheel blocks, jack and
wheel wrench.
The spare tire
is stored under the vehicle.
NOTICE:
Never remove or restow a tire frodto a
stowage position under the vehicle while the
vehicle is supported
by a jack. Always tighten the
tire
fully against the underside of the vehicle
when restowing.
To remove the spare, insert
the chisel end
of the wheel
wrench, on an angle, into the hole
in the rear bumper.
Be sure the chisel end
of the
wheel wrench connects into
the hoist shaft.
ProCarManuals.com

Turn the wheel wrench to the left to lower the spare tire.
Keep turning the wheel wrench until the spare tire can
be pulled out from under the vehicle.
Wflen the tire has been completely lowered,
tilt the
retainer at the end of the cable and
pull it through the
wheel opening.
Pull the tire out from under the vehicle.
~
(NOTICE: I
To help avoid vehicle damage, do not drive the
vehicle before the cable is restored.
I
F
Put the spare tire near the flat tire.
5-24
ProCarManuals.com

Position the chisel end of your wheel wrench in the
notch of the hub cap and pry off the hub cap.
Removing the Flat Tire and Installing the
Spare Tire
1. Using the wheel wrench, loosen all the wheel nuts.
Don't remove them yet.
2. Turn the jack handle to the right (clockwise) to raise
the jack
lift head.
5-25
-
ProCarManuals.com

3. Fit the jack into the appropriate hole nearest the
flat tire.
A. Front Frame Hole
B. Spring Hanger Hole
A CA" 1 Irk
Getting under a vehicle when it is ja, !d up is
dangerous.
If the vehicle slips off the jack, you
could be badly injured or killed. Never get under
a vehicle when it is supported only by a jack.
I A CAUTION:
Raising your vehicle with the jack improperly
positioned can damage the vehicle and even
make the vehicle
fall. To help avoid personal
injury and vehicle damage, be sure to
fit the jack
lift head into the proper location before raising
the vehicle.
ProCarManuals.com