1998 OLDSMOBILE BRAVADA reset

Windshield Wipers
I-
You control the windshield wipers by turning the band
with
the wiper symbol on it.
For a single wiping cycle, turn the band to MIST. Hold
it there until the wipers start, then let go. The wipers will
stop after
one wipe. If you want more wipes, hold the
band
on MIST longer.
rcm
can set the wiper speed for a long or short delay
between wipes. This can be very useful
in light rain or
snow. Turn the band
to choose the delay time. The
closer
to LO, the shorter the delay. For steady
wiping at
low speed, turn the band away
from
you to LO. For high-speed wiping, turn the
band further, to HI. To stop the wipers, rnove the
band
to OFF.
Be sure to clear ice and snow from the wiper blades
before using them.
If they’re frozen to the windshield,
carefully loosen
or thaw them. IF your blades do become
worn
or damaged, get new blades or blade inserts.
Windshield Washer
There‘s a paddle marked with the windshield washer
symbol
on the top of the rnultifunction lever. To spray
washer fluid
on the windshield, push the paddle. The
wipers
will clear the window and then either stop or
return to your preset speed.
In freezing weather, don’t use your washer until
the windshield
is warmed. Otherwise the washer
fluid can form ice on the windshield, blocking
your vision.
2-28
-
ProCarManuals.com

Setting Cruise Control
If you leave your cruise control switch on when
you’re not using cruise, you might hit
a button
and
go into cruise when you don’t want to. You
could
be startled and even lose control. Keep the
cruise control switch
off‘ until you want to use it.
1. Move the cruise control switch to ON.
2. Get up to the speed you want.
3. Press in the SET button
at the end
of the lever
4. Take your foot off the accelerator pedal.
Resuming a Set Speed
Suppose you set your cruise control at a desired speed
and then you apply the brake.
This, of course, shuts off
the cruise control. But you don’t need to reset it.
-1 Once you’re going about
25 lnph (40 km/h) or
more, you can move the
cruise control switch from
ON to R/A for about a half
a second.
You’ll
go right back up to your chosen speed and
stay there.
Remember,
if you hold the switch at R/A longer than
half
a second, the vehicle will keep going faster until
you release the switch or apply the brake, So unless you
want
to go faster, don’t hold the switch at R/A.
ProCarManuals.com

TRIP: Once in the TRIP mode, pressing the MODE
button will step you tlx-ough
the following TRIP functions:
AVG ECON: The average fuel economy since the
last reset
is displayed.
INST ECON: Instantaneous fuel economy for the
last second
of driving is displayed.
RANGE: The display indicates the estimated
distance that can be travelled
with the remaining fuel
in the tank, based on the fuel economy for the last
few hours
of driving.
FUEL USED: The fuel used since the last reset
is displayed.
AVG SPEED: The average speed since the last reset
is displayed.
To reset the trip computer, press the MODE and US/MET
buttons simultaneously for at least two seconds.
All
functions will be displayed for half a second once the
system is reset. Reset can only be performed
in the AVG
ECON, FUEL USED and AVG SPEED modes. All three
modes are reset simultaneously.
Sunglasses Storage Compartment
I
To open the sunglasses storage Compartment in the
overhead console, press the release button. Then pull the
compartment down.
2-40
ProCarManuals.com

Speedometer and Odometer
Your speedometer lets you see your speed in both miles
per hour (mph) and kilometers per hour (km/h).
Your odometer shows how far your vehicle
has been
driven, in miles.
You may wonder what happens
if your vehicle needs a
new odometer installed.
If the new one can be set to the
mileage total of the old odometer, then
it must be. But if
it can’t, then it’s set at zero, and a label must be put on
the driver’s door to show the old mileage reading when
the new odometer was installed.
Trip Odometer
The trip odometer can tell you how fa- your vehicle has
been driven since you last set the trip odometer to zero.
To view
the trip odometer, press the button near the
readout.
To reset the trip odometer, press the button
until it clears.
Tachometer
The tachometer displays the engine speed in revolutions
per minute (rpm). Each
tachometer has a different
limit depending on the
powertrain
in your vehicle. The tachometer has three
areas: normal operating range, red warning range and
red danger range.
The normal operating range shows your engine speed
during normal driving conditions. For example, when
the needle points to
2, it means the engine is running at
2,000 revolutions per minute (rpm). The tachometer
needle will vary all the time that the engine is running.
The shaded red warning range tells you that your engine
speed is reaching its upper limits. Don’t drive very long
with the tachometer in the red warning range. Lift your
foot off the accelerator pedal.
The solid red danger range tells you that your engine
speed
is at its upper limits. You should immediately shift
to
a higher gear, or lift your foot off the accelerator pedal.
I NOTICE:
Do not operate the engine with the tachometer in
the red range,
or engine damage will occur.
2-52
ProCarManuals.com

PUSHBUTTONS: The five numbered pushbuttons let
you return to your favorite stations. You can set up to
15 stations (five AM, five FMl and five FM2). Just:
1. Turn the radio on.
2. Press AM-FM to select the band.
3. Tune in the desired station.
4. Press TONE to select the equalization that best suits
the type of station selected.
5. Press and hold one of the five numbered buttons.
The sound will mute. When
it returns, release the
button. Whenever you press that numbered button,
the station you set will return and the tone that you
selected will also be automatically selected for
that button.
6. Repeat the steps for each pushbutton.
P SCAN: Press SCAN for more than two seconds, and
P SCAN will appear on the display. The radio will go to
the first preset station stored
on your pushbuttons, stop
for
a few seconds, then go on to the next preset station.
Press SCAN again to stop scanning.
Setting the Tone
BASS:
Press this knob lightly so
knob to increase or decrease bass
control, the radio’s tone setting
w
it extends. Turn the
. When YOLI use this
ill switch to manual.
TREB: Press this knob lightly so it extends. Then pull
the knob all the way out. Turn the knob to increase or
decrease treble. When you use this control, the radio’s
tone setting will switch to manual.
If a station is weak or
noisy, you may want to decrease the treble.
Push these knobs back into their stored positions when
you’re not using them.
TONE: This feature allows you to choose preset bass
and treble equalization settings designed for jazz, vocal,
pop, rock and classical stations. JAZZ
will appear on the
display when you first press
TONE. Each time you press
it, another setting will appear on the display. Press it
again after CLASSIC appears and MANUAL will
appear. Manual tone control
will return to the BASS
and TREB knobs. Also, if you use the BASS and
TREB knobs, control
will return to them and MANUAL
will appear.
3-9
ProCarManuals.com

FWD (2): Press this button to advance quickly to
another part
of the tape. Press the button again to return
to playing speed. The radio will play the last-selected
station while the tape advances. You may select stations
during
FWD operation by using TUNE.
PROG (3): Press this button to play the other side
of the tape.
00 (4): Press this button to reduce background
noise. Note that the double-D symbol will appear
on the display.
Dolby Noise Reduction is manufactured under
a license
from Dolby Laboratories Licensing Corporation. Dolby
and the double-D symbol are trademarks of Dolby
Laboratories Licensing Corporation.
TONE: Press this button to select a tone while playing a
cassette. The tone will be automatically set whenever
you play
a cassette tape.
SEEK: Press the up or down arrow to search for the
next or previous selection on the tape. Your tape must
have at least three seconds of silence between each
selection for
SEEK to work.
SCAN: Press this button to listen to each selection for a
few seconds. The tape will go to the next selection, stop for
a few seconds, then go
on to the next selection. Press
this button again to stop scanning. The sound will mute,
SCAN will appear on the display and
the tape direction
arrow will blink while scanning.
AM-FM: Press this button to play the malo wnen
a tape is in the player. The tape will stop but remain in
the player.
TAPE AUX: If YOLI have a tape inserted and the radio is
playing, press TAPE AUX to play your tape. To return
to the radio while a tape is playing, press
AM-FM. The
inactive tape will remain safely inside the radio for
future listening.
EJECT Press this button to remove the tape. The radio
will play. EJECT may be activated with either the
ignition or radio off. Cassettes may be loaded with the
radio and ignition
off if this button is pressed first.
CLN: If this message appears on the display, the
cassette tape player needs to be cleaned.
It will still play
tapes, but you should clean
it as soon as possible to
prevent damage to the tapes and player. See “Care of
Your Cassette Tape Player”
in the Index. After you clean
the player, press and hold EJECT for five seconds to
reset the CLN indicator. The radio will display
--- to
show the indicator
was reset.
3-11
ProCarManuals.com

PUSHBUTTONS: The five numbered pushbuttons let
you return to your fworite stations.
You can set up to
15 stations (five AM, five FMI and five FM2). Just:
1.
2.
3.
4.
5.
6.
Turn the radio on.
Press AM-FM to select the band.
Tune
in the desired station.
Press
TONE to select the equalization that best suits
the type of station selected.
Press and hold one of the five numbered buttons.
The sound will mute. When
it returns, release the
button. Whenever you press that numbered button,
the station you set will return and the tone that you
selected will also be automatically selected for
that button.
Repeat the steps for each pushbutton.
P SCAN: Press SCAN for more than two seconds, and
P SCAN will appear
on the display. The radio will go to
the first preset station stored on your pushbuttons, stop
for a few seconds,
then go on to the next preset station.
Press SCAN again
to stop scanning.
Setting the Tone
BASS: Press this knob lightly so it extends. Turn the
knob to increase or decrease bass. When
you use this
control, the radio's tone setting
will switch to manual.
TREB: Press this knob lightly so it extends. Then pull
the knob all the way out. Turn the knob to increase or
decrease treble. When you use this control, the radio's
tone setting will switch to manual.
If a station is weak or
noisy, you may want
to decrease the treble.
Push these knobs back into their stored positions when
you're not using them.
TONE: This feature allows you to choose preset bass
and treble equalization settings designed for jazz, vocal,
pop, rock and classical stations.
JAZZ will appear on the
display when you first press TONE. Each time you press
it, another setting will appear on the display. Press it
again after CLASSIC appears and MANUAL will
appear. Tone control will return to the BASS and TREB
knobs.
Also, if you use the BASS and TREB knobs,
control
will return to them and MANUAL will appear.
ProCarManuals.com

FWD (2): Press this button to advance quickly to
another part of the tape. Press the button again to return
to playing speed. The radio will play the last-selected
station while the tape advances. You may select stations
during FWD operation by using TUNE.
PROG (3): Press this button to play the other side
of the tape.
00 (4): Press this button to reduce background noise.
Note that the double-D symbol
will appear on the display.
Dolby Noise Reduction is manufactured under a license
from Dolby Laboratories Licensing Corporation. Dolby
and the double-D symbol are trademarks of Dolby
Laboratories Licensing Corporation.
TONE: Press this button to select a tone while playing a
cassette. The tone will be automatically set whenever
you play a cassette tape.
SEEK: Press the up or down arrow to search for the
next or previous selection on the tape. Your tape must
have at least three seconds
of silence between each
selection for SEEK
to work.
SCAN: Press this button to listen to each selection for a
few seconds. The tape
will go to the next selection, stop
for
a few seconds, then go on to the next selection. Press
this button again to stop scanning. The sound will mute while
scanning, SCAN will appear on the display and
the tape direction arrow will
blink while scanning.
AM-FM: Press this button to play the radio when
a tape is in the player. The tape will stop but remain in
the player.
TAPE-CD: Press this button if you have a disc loaded
in the CD player and the radio is playing, to play a
compact disc. Press AM-FM to return to the radio when
a compact disc is playing. Press TAPE-CD to switch
between the tape and compact disc
if both are loaded.
The inactive tape or CD will remain safely inside the
radio for future listening. The display will show TP
and CD.
EJECT Press this button to remove the tape. The radio
will play. EJECT may be activated with either the
ignition or radio off. Cassettes may be loaded with the
radio and ignition off
if this button is pressed first.
CLN: If this message appears on the display, the
cassette tape player needs to be cleaned.
It will still play
tapes, but you should clean
it as soon as possible to
prevent damage to the tapes and player. See "Care
of
Your Cassette Tape Player" in the Index. After you clean
the player. press and hold
EJECT for five seconds to
reset the
CLN indicator. The radio will display --- to
show the indicator was reset.
3-15
ProCarManuals.com