1998 MITSUBISHI MONTERO Fuel Pump

jump start terminals engine oil oil capacity coolant temperature wheel auxiliary battery location

Page 14 of 1501

$MITSUBISHI MONTERO 1998 Service Manual Accessory Mount Stay Bolt (Montero) 8 mm Bolt .............................................. 17 (23)\ 10 mm Bolt ............................................. 36 (49)\ Cooling Fan Br$

Accessory Mount Stay Bolt (Montero)
8 mm Bolt .............................................. 17 (23)\
10 mm Bolt ............................................. 36 (49)\
Cooling Fan Bracket (Montero) ............................ 30 (41\
)
Engine Hanger (Montero) .................................. 13 (17\
)
Generator Bolt (Diamante) ................................ 15 (21\
)
Generator Bolt (Montero)
8 mm Bolt .............................................. 15 (21)\
10 mm Bolt ............................................. 38 (51)\
Generator Bracket (Diamante)
8 mm Bolt .............................................. 35 (48)\
10 mm Bolt ............................................. 17 (23)\
Generator Pivot Nut (Diamante) ........................... 32 (44\
)
Tensioner Pulley Nut ..................................... 37 (50)\
Tensioner Bracket Stay Bolt (Montero) .................... 18 (24\
)
Intake Manifold & Fuel
Bracket (Montero) ........................................ 18 (24\
)
ECT Sensor ............................................... 22 (30)\
Intake Manifold Nut ...................................... 15 (21)\
Thermostat Case .......................................... 14 (19)\
Water Inlet Fitting Bolt ................................. 14 (19)\
Water Outlet Fitting Bolt ................................ 14 (19)\
Water Passage (Montero) .................................. 14 (19\
)
Heater Pipe Bolt (Diamante) .............................. 13 (18\
)
Intake Plenum & Throttle Body
Air Intake Fitting Bolt & Nut (Montero) .................. 13 (18\
)
EGR Pipe Bolt ............................................ 13 (18)\
EGR Pipe Flair Nut ....................................... 44 (59)\
EGR Valve Bolt ........................................... 16 (22)\
Intake Manifold Plenum (Diamante) ........................ 13 (18\
)
Intake Manifold Plenum Stay Bolt
8 mm Bolt .............................................. 13 (18)\
10 mm Bolt ............................................. 27 (36)\
Water Outlet Fitting Bracket Bolt ........................ 14 (19)\
Bracket (Diamante) ....................................... 18 (24\
)
Motor Mount Brackets
Bracket
8 mm Bolt .............................................. 16 (22)\
10 mm Bolt ............................................. 30 (41)\
12 mm Bolt ............................................. 55 (75)\
Oil Pan & Oil Pump
Drain Plug ............................................... 30 (40)\
Oil Cooler By-Pass Valve (Montero) ....................... 41 (55\
)
Oil Filter Bolt (Montero) ................................ 15 (21\
)
Oil Filter Bracket
8 mm Bolt .............................................. 18 (24)\
10 mm Bolt ............................................. 30 (40)\
Oil Screen
8 mm Bolt ............................................... 14 (19)\
Plug .................................................... 33 (45)\
Piston & Connection Rod
Connecting Rod Cap Nut ................................... 38 (52)\
Rocker Arms & Camshafts
Distributor Adapter Bolt (Diamante) ...................... 17 (23\
)
Rocker Arm Shaft Bolt .................................... 23 (31)\
Spark Plug ................................................. 18 (25)\
Timing Belt
Auto Tensioner Bolt ...................................... 18 (24)\
Camshaft Sprocket Bolt ................................... 65 (88)\
Idler Pulley Bolt ........................................ 32 (44)\
Tensioner Arm Bolt ....................................... 32 (44)\
Tensioner Pulley Bolt .................................... 36 (49)\
Water Pump Bolt (Montero) ................................ 18 (24\
)

Page 15 of 1501

$MITSUBISHI MONTERO 1998 Service Manual Water Pump Bolt (Diamante) 8 mm Bolt .............................................. 18 (24)\ 10 mm Bolt ............................................. 30 (41)\$

Water Pump Bolt (Diamante)
8 mm Bolt .............................................. 18 (24)\
10 mm Bolt ............................................. 30 (41)\
INCH Lbs. (N.m)
Crankshaft & Drive Plate
Bell Housing ............................................ 79.7 (9)\
Oil Seal Case .......................................... 97.3 (11)\
Rear Plate (Montero) ................................... 97.3 (11\
)
Exhaust Manifold
Heat Shield ........................................... 123.9 (14)\
Oil Level Gauge Guide Bolt ............................ 123.9 (14)\
Generator & Drive Belt
Cooling Fan Bolt (Montero) ............................. 97.3 (11\
)
Cooling Fan Nut (Montero) .............................. 97.3 (11\
)
Timing Indicator Bolt (Montero) ........................ 97.3 (11\
)
Intake Manifold & Fuel
ECT Gauge Sender ....................................... 97.4 (11)\
Fuel Pressure Regulator Bolt ............................ 79.6 (9)\
Fuel Pipe Banjo Bolt .................................... 79.6 (9)\
Injector & Fuel Rail Bolt ............................. 106.2 (12)\
Water Outlet Pipe ..................................... 123.9 (14)\
Intake Plenum & Throttle Body
Ignition Coil Bolt (Montero) ............................ 115 (13\
)
Manifold Differential Pressure (MDP) Sensor ............. 44 (4.9\
)
Throttle Body Bolt ...................................... 106 (12)\
Vacuum Hose Assembly (Diamante) ......................... 88 (9.8\
)
Oil Pan & Oil Pump
Baffle Plate (Montero) ................................. 97.3 (11\
)
Baffle Plate (Diamante) ................................ 97.3 (11\
)
6 mm Bolt ............................................... 53.1 (6)\
8 mm Bolt ............................................... 79.6 (9)\
Oil Pump Cover Bolt (Diamante) ......................... 88.5 (10\
)
Oil Pump Cover Bolt (Montero)
6 mm x 10 mm Bolt .................................... 97.3 (11)\
6 mm x 18 mm Bolt ..................................... 53.1 (6)\
Oil Pressure Gauge Sender .............................. 88.5 (10)\
Oil Pan (Upper) ......................................... 53.1 (6\
)
Oil Pan (Lower) ........................................ 97.3 (11\
)
Oil Pump Case ......................................... 123.9 (14)\
Oil Screen (Montero)
6 mm Bolt ............................................. 53.1 (9)\
Rocker Arms & Camshafts
Rocker Cover Bolt ....................................... 31 (3.5)\
Thrust Case Bolt ...................................... 115.1 (13)\
Timing Belt
Camshaft Position (CMP) Sensor (Montero) ................ 79.6 (\
9)
Crankshaft Position (CKP) Sensor ........................ 79.6 (9\
)
( 1) - Tighten cylinder head bolts in 2 or 3 steps with engine cold.
\
\
\
\
\
\
\

ENGINE SPECIFICATIONS
GENERAL SPECIFICATIONS
GENERAL SPECIFICATIONS\
\
\
\
\
\
\

Application Specification
Displacement .................................. 213.4 Cu. In. (3.5L)\
Bore ............................................... 3.6614" (93 mm)\

Page 28 of 1501

$MITSUBISHI MONTERO 1998 Service Manual \ \b\ \ \ \ \ \ EAC Electric Assist Choke$

\
\b\
\
\
\
\
\

EAC Electric Assist Choke

EACV Electric Air Control Valve

EBCM Electronic Brake Control Module

ECA Electronic Control Assembly

ECAT Electronically Controlled Automatic Transaxle

ECM Electronic Control Module

ECT Engine Coolant Temperature Sensor

ECU Electronic Control Unit or Engine Control Unit

EDF Electric Drive Fan relay assembly

EDIS Electronic Distributorless Ignition System

EEC Electronic Engine Control

EECS Evaporative Emission Control System

EEPROM Electronically Erasable PROM

EFE Early Fuel Evaporation

EFI Electronic Fuel Injection

EGO Exhaust Gas Oxygen sensor (see HEGO)

EGR Exhaust Gas Recirculation system

EGRC EGR Control solenoid or system

EGRV EGR Vent solenoid or system

EMR Emission Maintenance Reminder Module

ESA Electronic Spark Advance

ESC Electronic Spark Control

EST Electronic Spark Timing

ETR Emergency Tensioning Retractor

EVAP Fuel Evaporative System

EVIC Electronic Vehicle Information Center

EVO Electronic Variable Orifice

EVP EGR Valve Position Sensor

EVR EGR Valve Regulator

EVRV Electronic Vacuum Regulator Valve

Elect. Electronic

Eng. Engine

Evap. Evaporative

Exc. Except

\
\
\
\
\
\
\
\f

"F" ABBREVIATION TABLE
"F" ABBREVIATION TABLE\
\
\
\
\
\
\

ABBREVIATION DEFINITION

\
\b\
\
\
\
\
\

F Fahrenheit (Degrees)

F/B Fuse Block

FBC Feedback Carburetor

FI Fuel Injector or Fuel Injection

FICD Fast Idle Control Device

FIPL Fuel Injector Pump Lever

FP Fuel Pump

FPM Fuel Pump Monitor

FPR-VSV Fuel Pressure Regulator Vacuum Switching Valve

FWD Front Wheel Drive

Fed. Federal

Ft. Lbs. Foot Pounds

\
\
\
\
\
\
\
\f

"G" ABBREVIATION TABLE
"G" ABBREVIATION TABLE\
\
\
\
\
\
\

ABBREVIATION DEFINITION

Page 196 of 1501

$MITSUBISHI MONTERO 1998 Service Manual same axle to eliminate uneven braking behavior. Always wash drums after servicing or before installing. DRUM INSPECTION ��\ ��\ ��\ ��\$

same axle to eliminate uneven braking behavior. Always wash drums
after servicing or before installing.
DRUM INSPECTION
\
\
\
\
\
\
\

Condition Code Procedure
Balance weight missing .. .. ........ No service suggested or
required.
Bell-mouthed, affecting
performance ............ A ....... Require reconditioning or
replacement.
Cooling fin broken ...... .. ........ No service suggested or
required.
Cracked ................. B ............ Require replacement.
Drum diameter is greater
than OEM "machine to"
specifications but less
than "discard at"
specifications, and the
drum does not require
reconditioning ......... 1 ........ (1) Suggest replacement.
Drum diameter will exceed
OEM "machine to"
specifications after
required
reconditioning ......... B ........ ( 2) Require replacement.
Hard-spotted ............ 2 ....... Suggest reconditioning or
replacement.
Measured diameter is
greater than OEM discard
specifications ......... B ............ Require replacement.
Out-of-round (runout),
affecting performance .. A ....... Require reconditioning or
replacement.
Out-of-round (runout),
exceeding manufacturer's
specifications ......... B ....... Require reconditioning or
replacement.
Scored .................. B ....... Require reconditioning or
replacement.
Surface threaded due to
improper machining ..... B ....... Require reconditioning or
replacement.
Tapered, affecting
performance ............ A ....... Require reconditioning or
replacement.
( 1) - Only applies to vehicles for which OEM "machine to"
specifications exist. If OEM does not supply "machine to"
specifications, the drum may be worn to discard
specifications.
( 2) - If OEM does not supply "machine to" specifications, you
may machine to discard specifications.
\
\
\
\
\
\
\

ELECTRICAL PUMPS AND MOTORS
Copied fuel pump conditions from engine UIGs & deleted
pulsator from leaking conditions.
ELECTRICAL PUMP AND MOTOR INSPECTION
\
\
\
\
\
\
\

Page 255 of 1501

$MITSUBISHI MONTERO 1998 Service Manual ��\ ��\ ��\ ��\ ��\ ��\ �� Application ( 1) Basic ( 2) ( 3) ( 4) Actual$

\
\
\
\
\
\

Application ( 1) Basic ( 2) ( 3) ( 4) Actual
1.5L ............. 2-78@ 650-750 .......... 10 @ 600-800
1.8L ............. 2-8 @ 600-800 ........... 5 @ 600-800
2.0L
Non-Turbo ........... ( 5) ........................ ( 5)
Turbo .......... 2-8 @ 650-850 ........... 8 @ 650-850
2.4L ............. 2-8 @ 650-850 .......... 10 @ 650-850
3.0L ............. 2-8 @ 600-800 .......... 15 @ 600-800
3.5L ............. 2-8 @ 600-800 .......... 15 @ 600-800
( 1) - With ignition timing adjustment connector grounded or
vacuum hose (farthest from distributor) disconnected.
( 2) - With ignition timing adjustment connector ungrounded
or vacuum hose (farthest from distributor) connected.
( 3) - If vehicle altitude is more than 2300 feet above sea
level, actualtiming may be advanced (5 degrees).
( 4) - Actual ignition timing is approximate and may
fluctuate plus or minus 7 degrees.
( 5) - Ignition timing is NOT adjustable.
\
\
\
\
\
\

FUEL SYSTEM
FUEL PUMP
REGULATED FUEL PRESSURE TABLE\
\
\
\
\
\

At Idle w/Vacuum At Idle w/o Vacuum
Application psi (kg/cm) psi (kg/cm)
Eclipse 2.0L
Non-Turbo ............ ( 1) ........... 47-50 (3.3-3.5)
Turbo ............. 33 (2.3) ......... 42-45 (3.0-3.5)
3000GT Turbo ........ 34 (2.4) ......... 43-45 (3.0-3.1)
All Other Models .... 38 (2.7) ......... 47-50 (3.3-3.5)
( 1) - Information is not available from manufacturer at time
of publication.
\
\
\
\
\
\

IDLE SPEED
IDLE SPEED SPECIFICATIONS TABLE\
\
\
\
\
\

Application Curb Idle Basic Idle
1.5L & 1.8L ............ 600-800 ............... 650-750
2.0L
Non-Turbo ............ 700-900 ................... ( 1)
Turbo ................ 650-850 ............... 700-800
2.4L ................... 650-850 ............... 700-800
3.0L & 3.5L ............ 600-800 ............... 650-750
( 1) - Information is not available from manufacturer at time
of publication.
\
\
\
\
\
\

INJECTOR RESISTANCE
INJECTOR RESISTANCE TABLE

Page 458 of 1501

MITSUBISHI MONTERO 1998 Service Manual usage on specific models, see appropriate wiring diagram in
L - WIRING DIAGRAMS article. For theory and operation on each
output component, refer to system indicated after c

usage on specific models, see appropriate wiring diagram in
L - WIRING DIAGRAMS article. For theory and operation on each
output component, refer to system indicated after component.
Data Link Connector (DLC)
See SELF-DIAGNOSTIC SYSTEM .
EGR Control Solenoid Valve
See EXHAUST GAS RECIRCULATION (EGR) CONTROL under EMISSION
SYSTEMS.
Fuel Injectors
See FUEL CONTROL under FUEL SYSTEM.
Fuel Pressure Control Solenoid Valve (Turbo)
See FUEL DELIVERY under FUEL SYSTEM.
Fuel Pressure Regulator
See FUEL DELIVERY under FUEL SYSTEM.
Idle Air Control (IAC) Motor
See IDLE SPEED under FUEL SYSTEM.
Malfunction Indicator Light
See SELF-DIAGNOSTIC SYSTEM .
Power Transistor(s) & Ignition Coils
See IGNITION SYSTEMS .
Purge Control Solenoid Valve
See EVAPORATIVE CONTROL under EMISSION SYSTEMS.
Wastegate Control Solenoid Valve
See TURBOCHARGED ENGINES under AIR INDUCTION SYSTEM.
FUEL SYSTEM
FUEL DELIVERY
Electric fuel pump, located in gas tank, feeds fuel through
in-tank fuel filter, external fuel filter (located in engine
compartment) and fuel injector rail.
Fuel Pump
Fuel pump consists of a motor-driven impeller. Pump has an
internal check valve to maintain system pressure, and a relief valve
to protect fuel pressure circuit. Pump receives voltage supply from
MFI control relay.
Fuel Pressure Control Solenoid Valve (Turbo)
Valve prevents rough idle due to fuel percolation. On engine
restart, if engine coolant or intake air temperature reaches a preset
value, PCM applies voltage to fuel pressure control solenoid valve for
2 minutes after enginerestart. Valve will open, allowing atmospheric
pressure to be applied to fuel pressure regulator diaphragm. This
allows maximum available fuel pressure at injectors, enriching fuel
mixture and maintaining stable idle at high engine temperatures.
Fuel Pressure Regulator
Located on fuel injector rail, this diaphragm-operated relief
valve adjusts fuel pressure according to engine manifold vacuum.
As engine manifold vacuum increases (closed throttle), fuel

Page 465 of 1501

MITSUBISHI MONTERO 1998 Service Manual Fuel Pump Control Relay Behind right side of dash,
above ECM.
Generator Relay In engine compartment

Page 470 of 1501

MITSUBISHI MONTERO 1998 Service Manual Door Lock Control Unit Behind left side of dash.
ELC 4-Speed Automatic Transmission
Control Module Behind left side of dash.
Engine Control Module (ECM)

Door Lock Control Unit Behind left side of dash.
ELC 4-Speed Automatic Transmission
Control Module Behind left side of dash.
Engine Control Module (ECM) Behind right kick panel.
Keyless Entry Control Unit Behind right side quarter
panel.
Rear Differential Lock Control Unit Mounted on top of left rear
wheelwell.
SRS Air Bag Control Unit Behind center of dash.
Sun Roof Control Unit On center of roof, behind
sun roof.
Variable Shock Absorber Control Unit Behind left rear wheelwell,
behind quarter panel.
4WD Indicator Control Unit Behind center of dash.
\
\
\
\
\
\
\

MOTORS
\
\
\
\
\
\
\

Component Component Location\
\
\
\
\
\
\

Blower Motor Behind right side of dash.
Condenser Fan Motor On left front of engine
compartment.
Fuel Pump In fuel tank.
Headlight Washer Motor Right side of engine
compartment, in washer fluid
reservoir.
Idle Air Control Motor On throttle body.
Motor Antenna Rear of right front wheelwell.
Rear Differential Lock Air Pump On left rear of vehicle.
Rear Washer Motor In rear of cargo area.
Rear Wiper Motor On center of tailgate.
Sun Roof Motor On center of roof, behind
sun roof.
Windshield Washer Motor Bottom of windshield washer
reservoir.
Windshield Wiper Motor On left side of firewall.
\
\
\
\
\
\
\

SENDING UNITS & SENSORS

Load next 8 pages

Page: 1-8 9-16 17-24 25-32 33-40 ... 56 next >

radiator audio oil reset low beam child restraint rear view mirror