1998 MITSUBISHI MONTERO lock
[x] Cancel search: lockPage 178 of 1501
Fig. 1: Adjusting Key Interlock Cable (3000GT)
Courtesy of Mitsubishi Motor Sales of America.
Except 3000GT
Remove front console assembly. Move selector lever to "P".
Turn ignition switch to LOCK position. Loosen nut securing key
interlock cable. See Fig. 2. Gently push lock cam until pin stops in
direction of arrow. Tighten nut to specifications to secure cable. See
TORQUE SPECIFICATIONS. Install front console assembly.
Fig. 2: Adjusting Key Interlock Cable (Except 3000GT)
Courtesy of Mitsubishi Motor Sales of America.
SHIFT LOCK CABLE
Page 179 of 1501
3000GT
Remove front console assembly. Move selector lever to "P".
Loosen nuts securing shift lock cable and remove washer and cotter pin
at cable end. Turn lock cam counterclockwise to move set lever upward.
Fit cutout in set lever on pin of lock cam "B". Gently press set lever
down while pushing cable to take up slack. See Fig. 3. Tighten nut to
specifications to secure cable. See TORQUE SPECIFICATIONS. Ensure that
cable end contacts pin on lock cam, then install washer and cotter
pin.
Fig. 3: Adjusting Shift Lock Cable (3000GT)
Courtesy of Mitsubishi Motor Sales of America.
Except 3000GT
Remove front console assembly. Move selector lever to "P".
Loosen nuts securing shift lock cable. See Fig. 4. Adjust shift lock
cable so end of cable (Red mark) sits between lobe of lock cam, then
tighten nut to specifications to secure cable. See TORQUE
SPECIFICATIONS. Install front console assembly.
Page 180 of 1501
![MITSUBISHI MONTERO 1998 Service Manual Fig. 4: Adjusting Shift Lock Cable (Except 3000GT)
Courtesy of Mitsubishi Motor Sales of America.
TORQUE SPECIFICATIONS
TORQUE SPECIFICATIONS \
\](/manual-img/19/57333/w960_57333-179.png "MITSUBISHI MONTERO 1998 Service Manual Fig. 4: Adjusting Shift Lock Cable (Except 3000GT)
Courtesy of Mitsubishi Motor Sales of America.
TORQUE SPECIFICATIONS
TORQUE SPECIFICATIONS \
\")
Fig. 4: Adjusting Shift Lock Cable (Except 3000GT)
Courtesy of Mitsubishi Motor Sales of America.
TORQUE SPECIFICATIONS
TORQUE SPECIFICATIONS \
\
\
\
\
\
\
Application INCH Lbs. (N.m)\
Shift Lock Cable-To-Shift Console Assembly
3000GT ................................................... 89 (10)\
Diamante, Eclipse & Galant .............................. 106 (12)\
Montero & Montero Sport ................................... 44 (5)\
Mirage .................................................. 115 (13)\
Key Interlock Cable-To-Shift Console Assembly
3000GT ................................................... 89 (10)\
Diamante, Eclipse, Galant, Montero & Montero Sport ...... 106 (12)\
Mirage .................................................. 115 (13)\
\
\
\
\
\
\
\
Page 184 of 1501
* BRAKE SYSTEM UNIFORM INSPECTION GUIDELINES *
1998 Mitsubishi Montero
GENERAL INFORMATION
Brake Systems - Motorist Assurance Program
Standards For Automotive Repair
All Makes & Models
CONTENTS
OVERVIEW OF MOTORIST ASSURANCE PROGRAM
OVERVIEW OF SERVICE REQUIREMENTS AND SUGGESTIONS
ACCELEROMETERS (G SENSOR OR LATERAL)
ACCUMULATORS
ANCHOR PINS
ANTI-LOCK BRAKE SYSTEMS
BACKING PLATES
BRAKE FLUID
BRAKE FRICTION MATERIAL
BRAKE PADS
BRAKE PEDALS
BRAKE SHOES
BRAKE SHOE HARDWARE
BRAKE STOPLIGHT SWITCHES
BULB SOCKETS
BULBS AND LEDS
CALIPER HARDWARE
CALIPERS
CONTROLLERS
DIGITAL RATIO AXLE CONTROLLERS AND BUFFERS (DRAC AND DRAB)
DISABLE SWITCHES
DRUMS
ELECTRICAL PUMPS AND MOTORS
ELECTRONIC CONTROLLERS
FLUID
FLUID LEVEL SENSOR SWITCHES
FOUR WHEEL DRIVE SWITCHES
FRICTION MATERIAL
G SENSORS
HOSES
HYDRAULIC MODULATORS
HYDRO-BOOSTERS
HYDRO-ELECTRIC BOOSTERS (POWERMASTER)
IGNITION DISABLE SWITCHES
LATERAL ACCELERATION SWITCHES
LEDS
LENSES
MASTER CYLINDERS
MODULATORS
MOTORS
PARKING BRAKE SWITCHES
PARKING BRAKE SYSTEMS
PADS
PEDAL TRAVEL SWITCHES
PEDALS
POWERMASTER
PUMPS
PRESSURE DIFFERENTIAL SWITCHES
PRESSURE SWITCHES
RELAYS
ROTORS
SELF-ADJUSTING SYSTEMS
Page 188 of 1501
and make an informed decision about how to proceed.
BRAKES
SERVICE PROCEDURES REQUIRED & SUGGESTED FOR PROPER
VEHICLE OPERATION
Some states may have specifications that differ from OEM.
Check your local/state regulations. Where state or local laws are
stricter, they take precedence over these guidelines.
ACCELEROMETERS (G SENSOR OR LATERAL)
ACCELEROMETER INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Broken .................. A ............ Require replacement.
Connector loose ......... A .. Require repair or replacement.
Loose ................... B .. Require repair or replacement.
Missing ................. C ............ Require replacement.
Out of position ......... B ....... Require re-positioning to
vehicle manufacturer's
specifications.
Output signal incorrect . B ............ Require replacement.
\
\
\
\
\
\
\
ACCUMULATORS
ACCUMULATOR INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Leaking ................. B ............ Require replacement.
Missing ................. C ............ Require replacement.
Pre-charge incorrect .... B ............ Require replacement.
\
\
\
\
\
\
\
ANCHOR PINS
See BACKING PLATES .
ANTI-LOCK BRAKE SYSTEMS
NOTE: Anti-lock brakes are an integral part of the brake system. It
is essential that the anti-lock brakes function properly when
brake service is performed.
Anti-lock brake systems are commonly referred to as "ABS" and
will be referred to as "ABS" throughout these guidelines. Some ABS
components also function as part of a traction control system (TCS).
WARNING: When diagnosing and servicing high pressure components,
observe safety procedures and equipment requirements
established by the vehicle manufacturer to reduce the
possibility of serious personal injury.
NOTE: Intermittent electrical conditions are often caused by a loss
of ground, poor connection, or water intrusion into the
wiring harness.
Page 204 of 1501
(1) - This condition may be normal on some vehicles equipped with
anti-lock brakes.
( 2) - Refer to OEM procedures for adjusting low fluid level.
Inspect for brake hydraulic system leaks and friction
material wear.
( 3) - This condition may indicate contaminated brake fluid.
See BRAKE FLUID .
\
\
\
\
\
\
\
MODULATORS
See HYDRAULIC MODULATORS .
MOTORS
See ELECTRICAL PUMPS AND MOTORS .
PARKING BRAKE SWITCHES
See SWITCHES.
PARKING BRAKE SYSTEMS
NOTE: The parking brake is an integral part of the brake
system. It is important that the parking brake function
properly when brake service is performed.
PARKING BRAKE SYSTEM INSPECTION
\
\
\
\
\
\
\
Condition Code Procedure
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A ... Require repair or replacement
of hardware.
Cable improperly
adjusted ............... B ....... Require cable adjustment.
Cable or individual
wires in the cable
are broken ............. A .... Require replacement of cable
assembly.
Cable sticking .......... A ...... Require cable lubrication.
Cable stuck inside conduit
and cannot be lubricated
so that parking brake
functions properly ..... A .... Require replacement of cable
assembly.
Inoperative ( 1) ......... A .......... Require replacement of
inoperative parts.
Parking brake
parts bent ............. B ... Require repair or replacement
of bent parts.
Parking brake
parts broken ........... A ... Require replacement of broken
parts.
Parking brake parts
Page 206 of 1501
Terminal burned, not
affecting performance .. 2 .. Suggest repair or replacement.
Terminal corroded,
affecting performance .. A .. Require repair or replacement.
Terminal corroded, not
affecting performance .. 2 .. Suggest repair or replacement.
Terminal loose, affecting
performance ............ B .. Require repair or replacement.
Terminal loose, not
affecting performance .. 1 .. Suggest repair or replacement.
(1) - Inoperative includes intermittent operation or out of OEM
specification.
( 2) - Determine cause and correct prior to repair or
replacement of part.
\
\
\
\
\
\
\
ROTORS
Determine the need to recondition based upon individual rotor
conditions that follow. Friction material replacement does not require
rotor reconditioning unless other justifications exist. DO NOT
recondition new rotors unless they are being pressed or bolted onto an
existing hub. It is not necessary to replace rotors in axle sets.
However, when replacing or reconditioning a rotor due to the
conditions that follow, you may suggest reconditioning of the other
rotor on the same axle to eliminate uneven braking behavior.
Determine the need to replace based upon the individual rotor
conditions that follow. Reconditioning is defined as machining and
block sanding, or block sanding only. Block sanding is defined as
using 120-150 grit sandpaper with moderate to heavy force for 60
seconds per side. Always wash rotors after servicing or before
installing.
ROTOR INSPECTION
\
\
\
\
\
\
\
Condition Code Procedure
Corrosion affecting
structural integrity ... A ........ ( 1) Require replacement.
Cracked ................. B ............ Require replacement.
Hard spots .............. 2 ....... Suggest reconditioning or
replacement of rotor according
to OEM specifications.
Lateral runout (wobble)
exceeds OEM
specifications ......... B ............ Require re-indexing,
reconditioning, or replacement
according to specifications.
Measured thickness is less
than OEM discard
specifications ......... B ............ Require replacement.
Rotor thickness is less
than OEM "machine to"
specifications but thicker
than "discard at"
specifications, and the
rotor does not require
reconditioning ......... 1 ........ ( 2) Suggest replacement.
Rotor thickness will be
less than OEM "machine to"
specifications after
required
Page 218 of 1501
BRAKE SYSTEM
1998 Mitsubishi Montero
1997-98 BRAKES
Mitsubishi - Disc & Drum
Diamante, Eclipse, Galant, Mirage, Montero, Montero Sport,
3000GT
INTRODUCTION
This article contains information on repair and service of
basic hydraulic brake system. If vehicle is equipped with anti-lock
brakes, also see appropriate ANTI-LOCK article.
DESCRIPTION
Brake system consists of a master cylinder, vacuum power
brake booster, proportioning valve and self-adjusting assembly.
Montero has a Load-Sensing Proportioning Valve (LSPV). All models are
equipped with front disc brakes and either rear disc or drum brakes.
Parking brake assembly activates rear brakes.
BLEEDING BRAKE SYSTEM
BLEEDING PROCEDURES
Bleed brakes whenever hydraulic lines are opened or pedal
feels spongy. Bleed system in appropriate sequence. See
BRAKE LINE BLEEDING SEQUENCE table. Use only DOT 3 or DOT 4 approved
fluid and DO NOT mix fluid types.
BRAKE LINE BLEEDING SEQUENCE
\
\
\
\
\
\
\
Application Sequence
Diamante, Eclipse, Galant,
Mirage & 3000GT .................................... RR, LF, LR, RF
Montero ....................................... RR, LR, LSPV, RF, LF
Montero Sport ....................................... RR, LR, RF, LF
\
\
\
\
\
\
\
ADJUSTMENTS
BRAKE PEDAL HEIGHT, FREE PLAY & CLEARANCE
1) To measure brake pedal height, pull up carpet under brake
pedal. Measure distance between floor board and middle of brake pedal
pad surface with brake pedal released. See BRAKE PEDAL HEIGHT
SPECIFICATIONS table.
2) To adjust pedal height, separate connector from stoplight
switch, and loosen switch lock nut. Back-off switch so it does not
contact brake pedal arm. Loosen master cylinder push rod lock nut.
Adjust brake pedal height by rotating master cylinder push rod until
brake pedal height is within specification.
BRAKE PEDAL HEIGHT SPECIFICATIONS
\
\
\
\
\
\
\
Application Pedal Height: In. (mm)\