1998 MITSUBISHI MONTERO wiring

Fig. 18: Anti-Lock Brake System (ABS) Wiring Diagram (1997 Montero)\

Fig. 19: Anti-Lock Brake System (ABS) Wiring Diagram (1998 Montero)\

DIAGNOSTIC TROUBLE CODE IDENTIFICATION
DIAGNOSTIC TROUBLE CODE IDENTIFICATION








\









\









\









\









\









\









\







DTC ( 1) Probable Cause
11 ........................ Defective TP Sensor Or TP Sensor Circuit
15 ............................. Open Oil Temperature Sensor Circuit
16 ............................ Short Oil Temperature Sensor Circuit
21 ................................... Short Ignition Signal Circuit
22 .................................... Open Ignition Signal Circuit
23 .......................... Open Signal Line (ECT) From ECM To TCM\
24 ......................... Short Signal Line (ECT) From ECM To TCM\
29 ............................. Short Neutral Safety Switch Circuit
30 .............................. Open Neutral Safety Switch Circuit
31 ................................. Open No. 2 Speed Sensor Circuit
32 ................................. Open No. 1 Speed Sensor Circuit
41 ..................................... Open Solenoid No. 1 Circuit
42 .................................... Short Solenoid No. 1 Circuit
43 ..................................... Open Solenoid No. 2 Circuit
44 .................................... Short Solenoid No. 2 Circuit
47 ................................... Open Lock-Up Solenoid Circuit
48 .................................. Short Lock-up Solenoid Circuit
49 .............. ( 2) Torque Converter Clutch Engagement Malfunction
50 ........... ( 2) Torque Converter Clutch Disengagement Malfunction
51 ................................. 1st Gear Ratio Signal Incorrect
52 ................................. 2nd Gear Ratio Signal Incorrect
53 ................................. 3rd Gear Ratio Signal Incorrect
54 ................................. 4th Gear Ratio Signal Incorrect
( 1) - Check listed fault code and component for probable cause. See
appropriate fault code listing under DIAGNOSTIC TESTS. Check
wiring and connections of specified component.
( 2) - Scan tool is required for testing malfunctioning circuit.









\









\









\









\









\









\









\







Fig. 6: Identifying Data Link Connector (DLC) Terminals
Courtesy of Mitsubishi Motor Sales of America.

Once repairs have been performed, DTCs must be cleared from
TCM memory. DTCs may be cleared by disconnecting negative battery
cable for 10 seconds or more. Reconnect cable and ensure DTCs have
been cleared. Start engine and warm to normal operating temperature.
Run engine at idle for 10 minutes. DTCs may also be cleared using scan
tool. Refer to manufacturer's instruction manual.
DIAGNOSTIC TESTS
NOTE: For terminal and wire color identification, see WIRING
DIAGRAMS.
DTC 11: THROTTLE POSITION (TP) SENSOR
For diagnosis and testing information, see appropriate SELF-
DIAGNOSTICS article in ENGINE PERFORMANCE section. If TP sensor is
okay, check wiring harness and connectors between TP sensor and TCM.
Repair if necessary. If wiring harness and connectors are okay,
replace TCM.
DTC 15 & 16: OPEN OR SHORT IN OIL TEMPERATURE SENSOR CIRCUIT
1) Test oil temperature for proper operation. See OIL
TEMPERATURE SENSOR under COMPONENT TESTING. If oil temperature sensor
is okay, check wire harness, connectors and ground circuit for poor
connections or damage. Go to next step.
2) If wire harness and connectors are okay, check DTCs again
and verify code No. 15 or No. 16 still exists. If either code still
exists, replace TCM.
DTC 21 & 22: SHORT OR OPEN IN IGNITION SIGNAL CIRCUIT
1) Using an external tachometer, verify vehicles' tachometer
is operating accurately. If tachometer is incorrect, check ignition
coil and ignition power transistor and circuits for malfunction. See
appropriate SELF-DIAGNOSTICS article in ENGINE PERFORMANCE section.
2) If tachometer is okay, check TCM wire harness connector
for poor connection. If wire harness is okay, recheck DTCs. If codes
reappear check wire harness between ignition power transistor and TCM.
If wire harness is okay, replace TCM.
DTC 23 & 24: OPEN OR SHORT IN SIGNAL LINE (ECT) FROM ECM TO
TCM
Check wire harness, connectors and ground circuit for poor
connections or damage. Go to next step. If wire harness and connectors
are okay, check DTCs again and verify code No. 23 or No. 24 still
exists. If either code still exists, replace TCM.
DTC 29 & 30: SHORT OR OPEN IN PARK/NEUTRAL POSITION (PNP)
SWITCH CIRCUIT
1) Check PNP switch for correct operation. See. If PNP switch
is okay, disconnect switch connector and measure voltage between
harness connector terminal No. 1 and ground.
2) If battery voltage does not exist, check wire harness and
connectors. See WIRING DIAGRAMS. If battery voltage exists, check wire
harness and connectors between PNP switch and TCM. If wire harness is
okay, replace TCM.
DTC 31: INPUT SPEED SENSOR

1) Check input speed sensor. See INPUT SPEED SENSOR under
COMPONENT TESTING. If resistance is as specified, reconnect speed
sensor connector and go to next step. If resistance is not as
specified replace input speed sensor and recheck DTCs.
2) Connect voltmeter between solenoid and sensor connector
terminals No. 9 and No. 10. See Fig. 9. Lift and support vehicle to
allow drive wheels to spin freely. With transmission in "D" position,
engine at 1000 RPM and wheel speed at 19 MPH (30 km/h). Measured
voltage should be .3-2.5 volts.
3) If voltage is as specified, go to next step. If voltage is
not as specified, replace input speed sensor. If DTC still exists,
check speed sensor rotor. See MITSUBISHI R4AW3 & V4AW3 OVERHAUL
article. If DTC still exists after speed sensor rotor is replaced,
check for noise interference and repair.
4) Check and repair wiring harness and connectors between
input speed sensor and TCM. If wiring is okay, recheck DTC. If DTC
still exists, replace TCM.
Fig. 9: Identifying Sensor & Solenoid Connector Terminals
Courtesy of Mitsubishi Motor Sales of America.
DTC 32: OUTPUT SPEED SENSOR
1) Check output speed sensor. See OUTPUT SPEED SENSOR under
COMPONENT TESTING. If resistance is as specified, reconnect speed
sensor connector and go to next step. If resistance is not as
specified replace output speed sensor and recheck DTCs.
2) Connect voltmeter between solenoid and sensor connector
terminals No. 3 and No. 4. See Fig. 9. Lift and support vehicle to
allow drive wheels to spin freely. With transmission in "D" position,
engine at 1000 RPM and wheel speed at 19 MPH (30 km/h). Measured

voltage should be .3-2.5 volts.
3) If voltage is as specified, go to next step. If voltage is
not as specified, replace the output speed sensor. If DTC still
exists, check speed sensor rotor. See MITSUBISHI R4AW3 & V4AW3
OVERHAUL article. If DTC exists after speed sensor rotor is replaced,
check for noise interference and repair.
4) Check and repair wiring harness and connectors between
output speed sensor and TCM. If wiring is okay, recheck DTCs. If DTCs
still exists, replace TCM.
DTC 41 & 42: OPEN OR SHORT IN SOLENOID NO. 1 CIRCUIT
NOTE: A stuck solenoid will not set a DTC. DTCs are only set for
circuit malfunctions, not mechanical failures.
1) Disconnect solenoid and sensor connector. Using ohmmeter,
check resistance between solenoid connector terminal No. 6 and ground.
See Fig. 9 . Resistance should be 11-15 ohms at 77
F (25C). If
resistance is as specified, go to next step. If resistance is not as
specified, replace solenoid No. 1 and recheck DTC.
2) Check wiring harness and connectors between solenoid No. 1
and TCM. If wiring and solenoid No. 1 is okay, replace TCM.
DTC 43 & 44: OPEN OR SHORT IN SOLENOID NO. 2 CIRCUIT
NOTE: A stuck solenoid will not set a DTC. DTCs are only set for
circuit malfunctions, not mechanical failures.
1) Disconnect solenoid and sensor connector. Using ohmmeter,
check resistance between solenoid connector terminal No. 7 and ground.
See Fig. 9 . Resistance should be 11-15 ohms at 77
F (25C). If
resistance is as specified, go to next step. If resistance is not as
specified, replace solenoid No. 2 and recheck DTC.
2) Check wiring harness and connectors between solenoid No. 2
and TCM. If wiring and solenoid No. 2 is okay, replace TCM.
DTC 47 & 48: OPEN OR SHORT IN LOCK-UP SOLENOID CIRCUIT
NOTE: A stuck solenoid will not set a DTC. DTCs are only set for
circuit malfunctions, not mechanical failures.
1) Disconnect solenoid and sensor connector. Using ohmmeter,
check resistance between solenoid connector terminal No. 8 and ground.
See Fig. 9 . Resistance should be 11-15 ohms at 77
F (25C). If
resistance is as specified, go to next step. If resistance is not as
specified, replace lock-up solenoid and recheck DTC.
2) Check wiring harness and connectors between lock-up
solenoid and TCM. If wiring and lock-up solenoid is okay, replace TCM.
DTC 49: TORQUE CONVERTER CLUTCH (TCC) ENGAGEMENT MALFUNCTION
1) Using scan tool, verify vehicle tachometer and scan tool
vehicle RPM values are identical. If tachometer values are identical,
go to next step. If tachometer values are different, test ignition
signal circuit. See DTC 21 & 22: SHORT OR OPEN IN IGNITION SIGNAL
CIRCUIT.
2) Lift and support vehicle to allow drive wheels to spin
freely. With transmission in "D" position, run engine to 1300-1900
RPM. Verify scan tool and speedometer read 31 MPH (50 km/h). If values\
are identical, go to next step. If values are different, test input
speed sensor. See DTC 31: INPUT SPEED SENSOR.
3) Check lock-up solenoid for proper operation. See SOLENOIDS

under COMPONENT TESTING. If lock-up solenoid is okay, go to next step.
If lock-up solenoid is bad, replace and retest system.
4) Check wiring harness and connectors between lock-up
solenoid and TCM. If wiring harness and connectors are okay, check TCC
engagement hydraulic pressure, valve body malfunction or TCC slipping.
DTC 50: TCC DISENGAGEMENT MALFUNCTION
1) Using scan tool, verify vehicle tachometer and scan tool
vehicle RPM values are identical. If tachometer values are identical,
go to next step. If tachometer values are different, test ignition
signal circuit. See DTC 21 & 22: SHORT OR OPEN IN IGNITION SIGNAL
CIRCUIT.
2) Lift and support vehicle to allow drive wheels to spin
freely. With transmission in "D" position, run engine to 1300-1900
RPM. Verify scan tool and speedometer read 31 MPH (50 km/h). If values\
are identical, go to next step. If values are different, test input
speed sensor. See DTC 31: INPUT SPEED SENSOR.
3) Check lock-up solenoid for proper operation. See SOLENOIDS
under COMPONENT TESTING. If lock-up solenoid is okay, go to next step.
If lock-up solenoid is bad, replace and retest system.
4) Check wiring harness and connectors between lock-up
solenoid and TCM. If wiring harness and connectors are okay, check
valve body malfunction or TCC sticking.
DTC 51: 1ST GEAR RATIO SIGNAL INCORRECT
1) If DTC 31 is set, go to DTC 31: INPUT SPEED SENSOR. If DTC
31 is not set and DTC 32 is set, go to DTC 32: OUTPUT SPEED SENSOR. If
neither DTC 31 nor DTC 32 is set, go to next step.
2) Test input speed sensor. See INPUT SPEED SENSOR under
COMPONENT TESTING. If resistance is as specified, go to next step. If
resistance is not as specified, replace input speed sensor and recheck
DTC. If DTC still exists, go to step 5).
3) Test output speed sensor. See OUTPUT SPEED SENSOR under
COMPONENT TESTING. If resistance is as specified, go to next step. If
resistance is not as specified, replace output speed sensor and
recheck DTC. If DTC still exists, go to step 5).
4) If referenced here from another DTC, go back to referenced
DTC. Check No. 2 one-way clutch system. See NO. 2 ONE-WAY CLUTCH in
MITSUBISHI R4AW3 & V4AW3 OVERHAUL article.
5) Check output speed sensor and No. 2 speed sensor shielding
wire. Repair as necessary. If shielding wire is okay, recheck DTC. If
DTC still exists, replace sensor rotor. If DTC still exists after
sensor rotor is replaced, check for interference noise and repair.
DTC 52: 2ND GEAR RATIO SIGNAL INCORRECT
If DTC 51 is set also, go to DTC 51: 1ST GEAR RATIO SIGNAL
INCORRECT test. If DTC 51 is not set, check 2nd brake and No. 1 one-
way clutch systems for a mechanical failure. See 2ND BRAKE and NO. 1
ONE-WAY CLUTCH in MITSUBISHI R4AW3 & V4AW3 OVERHAUL article.
DTC 53: 3RD GEAR RATIO SIGNAL INCORRECT
If DTC 51 is set also, go to DTC 51: 1ST GEAR RATIO SIGNAL
INCORRECT test. If DTC 51 is not set, check direct clutch system for a
mechanical failure. See DIRECT CLUTCH in MITSUBISHI R4AW3 & V4AW3
OVERHAUL article.
DTC 54: 4TH GEAR RATIO SIGNAL INCORRECT

If DTC 51 is set also, go to DTC 51: 1ST GEAR RATIO SIGNAL
INCORRECT test. If DTC 51 is not set, check overdrive brake for a
mechanical failure. See OVERDRIVE BRAKE in MITSUBISHI R4AW3 & V4AW3
OVERHAUL article.
SYMPTOM TROUBLE SHOOTING
NOTE: Check system using appropriate scan tool. See WIRING DIAGRAMS
for electrical schematics and COMPONENT TESTING.
COMMUNICATION WITH SCAN TOOL NOT POSSIBLE
If scan tool cannot communicate with TCM, check proper
connection with DLC. Check TCM power circuits, TCM ground circuits and
malfunctioning TCM.
SHIFT POINTS INCORRECT
If shift points are incorrect, check for DTCs. If no DTC is
present, check oil temperature sensor, pattern select switch, 4WD low
range detection switch and TCM for proper operation.
UPSHIFTS OCCUR SPONTANEOUSLY
If upshifting occurs spontaneously, check park/neutral
position switch, overdrive switch and TCM for proper operation.
TCC LOCK-UP MALFUNCTIONING
If TCC lock-up system is not operating properly, check torque
converter, valve body, lock-up switch and oil temperature switch.
COMPONENT TESTING
A/T FLUID TEMPERATURE SWITCH
1) Remove fluid temperature switch, located to rear of
neutral safety switch. Immerse switch in container of ATF up to top
threaded portion of switch. Using a DVOM, check continuity between
switch terminals. Continuity should not exist when fluid temperature
is 257
F (125C) or less.
2) When fluid is heated to 289-304F (143-151C), continuity
should exist. Replace switch if necessary. Apply thread sealant to
fluid temperature switch threads and install in transmission.
BRAKELIGHT SWITCH
1) Disconnect electrical connector from brakelight switch,
located near brake pedal. Using ohmmeter, ensure continuity exists
between terminal No. 2 (White/Red wire) and terminal No. 3 (Green
wire) with brake pedal released. Replace brakelight switch if
continuity does not exist. Continuity should not exist between
terminals No. 2 and No. 3 with brake pedal depressed.
2) If continuity does not exist, ensure brake pedal is
properly adjusted so brakelight switch has proper travel for switch
operation. If proper brakelight switch travel exists, replace
brakelight switch.
ENGINE COOLANT TEMPERATURE (ECT) SENSOR