1998 MITSUBISHI MONTERO wiring

Fig. 14: Manual A/C-Heater System Wiring Diagram
Courtesy of Mitsubishi Motor Sales of America.

When ignition switch is turned to ON or START position, SRS
warning light on instrument panel should come on for about 7 seconds
and then go off. This indicates SRS-ECU has determined SRS is
functioning properly. If SRS warning light flashes, stays on all the
time, or does not come on, a fault exists in SRS. See
DIAGNOSIS & TESTING.
FRONT IMPACT SENSORS
Sensors are inertia switches that verify direction and
severity of impact. If impact is great enough, switch contacts close,
completing an electrical circuit. Front impact sensors are located
under front fenders. See Fig. 1.
AIR BAG MODULE(S)
An inflator assembly in the air bag module produces nitrogen
gas to fill air bag. See Fig. 1. When a small amount of current from
SRS-ECU is applied, ignitor starts a thermal reaction, which spreads
to a pellet-filled canister that produces nitrogen gas. Gas pressure
builds and discharges from inflator through a diffuser and screen
assembly, forcing trim cover to burst along its seams until air bag is
fully inflated. When air bag is fully inflated, gas escapes through
vents on sides of air bag.
SRS AIR BAG CONTROL UNIT (ECU)
SRS-ECU (with integral safing and analog impact sensor) is
located behind front floor console assembly. See Fig. 1. If a system
fault occurs, SRS-ECU memory stores a diagnostic trouble code (DTC).
DATA LINK CONNECTOR (DLC)
DLC is located under left side of dash. See Fig. 1. DLC is
used to access SRS self-diagnostics through Mitsubishi Multi-Use
Tester II (MUT-II) (MB991502).
CLOCKSPRING
Clockspring connects driver-side air bag module to steering
column wiring, forming SRS circuit. See Fig. 1. Clockspring is a flat,
ribbon-like cable that winds and unwinds when steering wheel is
turned. Because of clockspring's constant movement, it is the most
fragile part in the system.
SYSTEM OPERATION CHECK
WARNING: After servicing, always turn ignition on from passenger-side
of vehicle in case of accidental air bag deployment.
Turn ignition switch to ON position. SRS warning light on
instrument panel should come on for about 7 seconds and then turn off.
This indicates SRS is functioning properly. If SRS warning light does
not come on, stays on, or comes on while driving, SRS is
malfunctioning and needs repair. See DIAGNOSIS & TESTING.
SERVICE PRECAUTIONS
Observe the following precautions when working with SRS:
* Disable SRS before servicing any SRS or steering column

clockspring, the steering wheel may not turn completely, or
flat cable inside clockspring may be severed, disabling SRS
system and possibly causing serious injury to driver.
Installation
1) Ensure front wheels are in straight-ahead position. Align
mating marks on clockspring. See CLOCKSPRING CENTERING under
ADJUSTMENTS. Install clockspring. To install remaining components,
reverse removal procedure. Before installing air bag module, ensure
horn switch wiring is positioned so that it will not be pinched.
2) Tighten fasteners to spec. See TORQUE SPECIFICATIONS.
Activate SRS. See DISABLING & ACTIVATING AIR BAG SYSTEM . Check AIR BAG
warning light for proper system function. SYSTEM OPERATION CHECK.
PASSENGER-SIDE AIR BAG MODULE
Removal & Installation
1) Before proceeding, see SERVICE PRECAUTIONS. Deactivate
SRS. See DISABLING & ACTIVATING AIR BAG SYSTEM .
2) Remove right-side foot shower duct and two stoppers on
either side. Remove and lower glove box. Disconnect air bag module
connector. Remove retaining bolts and passenger-side air bag module.
See Fig. 5 .
3) To install, reverse removal procedure. Tighten bolts to
specification. See TORQUE SPECIFICATIONS . Activate SRS. See procedures
under DISABLING & ACTIVATING AIR BAG SYSTEM . Check AIR BAG warning
light for proper system function. SYSTEM OPERATION CHECK.
Fig. 5: Removing Passenger-Side Air Bag Module
Courtesy of Mitsubishi Motor Sales of America.
SRS AIR BAG CONTROL UNIT (ECU)

CLOCKSPRING CENTERING
WARNING: If front wheels are not in straight-ahead position or
clockspring mating marks are not aligned before installing
clockspring, the steering wheel may not turn completely, or
flat cable inside clockspring may be severed, disabling SRS
system and possibly causing serious injury to driver.
With clockspring removed, ensure front wheels are in
straight-ahead position. Turn clockspring fully clockwise, and then
turn it back approximately 3.3 turns counterclockwise to align mating
marks. See Fig. 8.
Fig. 8: Aligning Clockspring Mating Marks
Courtesy of Mitsubishi Motor Sales of America.
WIRE REPAIR
DO NOT repair SRS wiring or harness connectors. If SRS wiring
or harness connectors are faulty, replace faulty wiring harness.
TORQUE SPECIFICATIONS
TORQUE SPECIFICATIONS








\









\









\









\









\









\







Application Ft. Lbs. (N.m)
Steering Wheel Nut ............................... 29 (39)

Symptom Inspection Procedure
Communication With All Systems Not Possible ............ 1
Communication With SRS Only Not Possible ............... 2
Ignition Switch On (Engine Stopped)
SRS Warning Light Does Not Come On ............... DTC 43
SRS Warning Light Stays On After 7 Seconds ...... DTC 43









\









\









\









\









\









\







INSPECTION PROCEDURE 1
The cause is probably in power supply system (including
ground circuit of diagnostic line). Check connectors and harness, and
repair if necessary.
INSPECTION PROCEDURE 2
NOTE: Refer to WIRING DIAGRAMS for connector identification.
1) Before proceeding, see SERVICE PRECAUTIONS. Deactivate
SRS. See DISABLING & ACTIVATING AIR BAG SYSTEM .
2) Measure SRS Check Harness (MB991613) connector No. 5.
Disconnect SRS-ECU connector C-122 and connect SRS check harness
connector No. 3 to C-122. Check continuity between terminal No. 20, 21
and ground. If there is no continuity, go to next step. If there is
continuity, go to step 4).
3) Check connector C-122, and repair if necessary. If
connector is okay, check for trouble symptoms. If fault exists, check
harness between SRS-ECU and ground, and repair if necessary.
4) Measure SRS check harness connector No. 5. Disconnect SRS-
ECU connector C-122 and connect SRS harness check connector No. 3 to
C-122. Connect negative battery cable. Measure voltage between
terminal No. 13 and 14, and body ground. If voltage at terminals is 9
volts or more, check harness wire between SRS-ECU and Data Link
Connector (DLC), and repair if necessary. If harness wire is okay,
replace SRS-ECU. See SRS AIR BAG CONTROL UNIT (ECU) under REMOVAL &
INSTALLATION. If voltage is not as specified, check connector C-80, C-
93, C-101, and C-132, and repair if necessary. If connectors are okay,
check for trouble symptoms. If fault exists, check harness between
SRS-ECU and IG1 A or B (ignition switch), and repair if necessary.
Fig. 10: Identifying SRS Check Harness (MB991613) Connectors
Courtesy of Mitsubishi Motor Sales of America.
DTC 11, 12 & 13: FRONT IMPACT SENSOR SYSTEM

NOTE: Refer to WIRING DIAGRAMS for connector identification.
1) Before proceeding, see SERVICE PRECAUTIONS. Deactivate
SRS. See DISABLING & ACTIVATING AIR BAG SYSTEM .
2) Check front impact sensor, and replace if necessary. See
FRONT IMPACT SENSORS under REMOVAL & INSTALLATION. Measure SRS Check
Harness (MB991613) connector No. 5. Disconnect SRS-ECU connector C-122\
and connect SRS check harness connector No. 3 to C-122. Measure
resistance between terminals for normal value of 1,900-2,100 ohms. If
resistance is not as specified, go to next step. If resistance is as
specified, check for trouble symptoms. If fault exists, replace SRS-
ECU. See SRS AIR BAG CONTROL UNIT (ECU) under REMOVAL & INSTALLATION.
3) Check connector A-71, A-75, C-113, and C-122, and repair
if necessary. If connectors are okay, check for trouble symptoms. If
fault exists, inspect harness between SRS-ECU and front impact sensor,
and replace harness if necessary.
DTC 14: ANALOG "G" SENSOR SYSTEM
Before proceeding, see SERVICE PRECAUTIONS. Replace SRS-ECU.
See SRS AIR BAG CONTROL UNIT (ECU) under REMOVAL & INSTALLATION.
DTC 15 & 16: SAFING "G" SENSOR SYSTEM
Before proceeding, see SERVICE PRECAUTIONS. Replace SRS-ECU.
See SRS AIR BAG CONTROL UNIT (ECU) under REMOVAL & INSTALLATION.
DTC 21, 22 & 61: DRIVER-SIDE AIR BAG MODULE (SQUIB) SYSTEM
WARNING: During the following procedure, never measure circuit
resistance of air bag module (squib), even when using
specified DVOM. If circuit resistance is measured, it may
cause accidental air bag deployment and personal injury.
NOTE: Refer to WIRING DIAGRAMS for connector identification.
1) Before proceeding, see SERVICE PRECAUTIONS. Deactivate
SRS. See DISABLING & ACTIVATING AIR BAG SYSTEM .
2) Perform clockspring test, and repair as necessary. See
CLOCKSPRING TEST under COMPONENT TESTING. Disconnect clockspring
connector C-129. Connect SRS Check Harness (MB991613) connector No. 1
to clockspring connector. Connect negative battery cable. Erase DTC
memory and check if DTCs 21, 22, or 61 are set. If any of these DTCs
are output, go to next step. If DTCs are not output, go to step 4).
3) Check SRS-ECU connector C-122 and clockspring connector C-
129, and repair as necessary. If connectors are okay, check for
trouble symptoms. If fault exists, check harness between SRS-ECU and
clockspring. Disconnect connector C-122 and C-129. Connect SRS Check
Harness connector No. 1 to C-129 and No. 3 to C-122. Check resistance
between terminals No. 5 and 6. If resistance is approximately 3 ohms,
replace SRS-ECU. See SRS AIR BAG CONTROL UNIT (ECU) under REMOVAL &
INSTALLATION. If resistance is not as specified, repair as necessary.
4) Check connector C-129 and 1 (air bag module connector),
and repair if necessary. If connectors are okay, check trouble
symptoms. If fault exists, replace driver-side air bag module. See
DRIVER-SIDE AIR BAG MODULE under REMOVAL & INSTALLATION.
DTC 24, 25 & 64: PASSENGER-SIDE AIR BAG MODULE (SQUIB) SYSTEM
WARNING: During the following procedure, never measure circuit
resistance of air bag module (squib), even when using
specified DVOM. If circuit resistance is measured, it may

cause accidental air bag deployment and personal injury.
NOTE: Refer to WIRING DIAGRAMS for connector identification.
1) Before proceeding, see SERVICE PRECAUTIONS. Deactivate
SRS. See DISABLING & ACTIVATING AIR BAG SYSTEM .
2) Disconnect passenger-side air bag connector C-107. Connect
SRS Check Harness (MB991613) connector No. 1 to passenger-side air bag\
connector. Erase DTC memory and check if DTCs 24, 25, or 64 are set.
If any of these DTCs are output, go to next step. If DTCs are not
output, replace passenger-side air bag module. See
PASSENGER-SIDE AIR BAG MODULE under REMOVAL & INSTALLATION.
3) Check connectors C-107 and C-122, and repair if necessary.
If connectors are okay, check trouble symptoms. If fault is still
present, check harness wire between passenger-side air bag module and
SRS-ECU, and repair if necessary. If harness wire is okay, replace
SRS-ECU. See SRS AIR BAG CONTROL UNIT (ECU) under REMOVAL &
INSTALLATION.
DTC 31 & 32: SRS-ECU CAPACITOR SYSTEM
Before proceeding, see SERVICE PRECAUTIONS. Replace SRS-ECU.
See SRS AIR BAG CONTROL UNIT (ECU) under REMOVAL & INSTALLATION.
DTC 34: CONNECTOR LOCK SYSTEM
NOTE: If vehicle condition returns to normal, DTC will be erased
and SRS warning light will return to normal.
NOTE: Refer to WIRING DIAGRAMS for connector identification.
Before proceeding, see SERVICE PRECAUTIONS. Check connector
C-122 and repair if necessary. If connector is okay, check for trouble
symptom. If fault exists, replace SRS-ECU. See
SRS AIR BAG CONTROL UNIT (ECU) under REMOVAL & INSTALLATION.
DTC 35: SRS-ECU SYSTEM (AFTER AIR BAG DEPLOYMENT)
Before proceeding, see SERVICE PRECAUTIONS. Replace SRS-ECU.
See SRS AIR BAG CONTROL UNIT (ECU) under REMOVAL & INSTALLATION.
DTC 41: IG1 (A) POWER CIRCUIT SYSTEM
NOTE: If vehicle condition returns to normal, DTC will be erased
and SRS warning light will return to normal.
NOTE: Refer to WIRING DIAGRAMS for connector identification.
1) Before proceeding, see SERVICE PRECAUTIONS. Deactivate
SRS. See DISABLING & ACTIVATING AIR BAG SYSTEM .
2) Measure SRS Check Harness (MB991613) connector No. 5.
Disconnect SRS-ECU connector C-122 and connect SRS check harness
connector No. 3 to C-122. Check terminal No. 20 and 21 for continuity
to ground. If there is no continuity, go to next step. If there is
continuity, go to step 4).
3) Check connector C-122 and repair if necessary. If
connector is okay, check for trouble symptom. If fault exists, check
harness wire between SRS-ECU and ground, and repair if necessary.
4) Measure SRS check harness connector No. 5. Disconnect SRS-
ECU connector C-122 and connect SRS harness check connector No. 3 to
C-122. Connect negative battery cable and turn ignition switch to ON
position. If voltage between terminal No. 14 and body ground is 9

volts or more, replace SRS-ECU. See SRS AIR BAG CONTROL UNIT (ECU)
under REMOVAL & INSTALLATION. If voltage is not as specified, check
connector C-93, C-101, and C-132, and repair if necessary. If
connectors are okay, check for trouble symptoms. If fault still
exists, check harness wire between SRS-ECU and ignition switch IG1
(A), and repair if necessary.
DTC 42: IG1 (B) POWER CIRCUIT SYSTEM
NOTE: If vehicle condition returns to normal, DTC will be erased
and SRS warning light will return to normal.
NOTE: Refer to WIRING DIAGRAMS for connector identification.
1) Before proceeding, see SERVICE PRECAUTIONS. Deactivate
SRS. See DISABLING & ACTIVATING AIR BAG SYSTEM .
2) Measure SRS Check Harness (MB991613) connector No. 5.
Disconnect SRS-ECU connector C-122 and connect SRS check harness
connector No. 3 to C-122. Check terminal No. 20 and 21 for continuity
to ground. If there is no continuity, go to next step. If there is
continuity, go to step 4).
3) Check connector C-122 and repair if necessary. If
connector is okay, check for trouble symptoms. If fault still exists,
check harness wire between SRS-ECU and ground, and repair if
necessary.
4) Measure SRS check harness connector No. 5. Disconnect SRS-
ECU connector C-122 and connect SRS harness check connector No. 3 to
C-122. Connect negative battery cable and turn ignition switch to ON
position. If voltage between terminal No. 13 and body ground is 9
volts or more, replace SRS-ECU. See SRS AIR BAG CONTROL UNIT (ECU)
under REMOVAL & INSTALLATION. If voltage is not as specified, check
connector C-80, C-93, and C-101, and repair if necessary. If
connectors are okay, check for trouble symptoms. If fault still
exists, check harness wire between SRS-ECU and ignition switch IG1
(B), and repair if necessary.
DTC 43: SRS WARNING LIGHT CIRCUIT
NOTE: Refer to WIRING DIAGRAMS for connector identification.
Light Does Not Come On
1) Before proceeding, see SERVICE PRECAUTIONS. Deactivate
SRS. See DISABLING & ACTIVATING AIR BAG SYSTEM .
2) Measure SRS Check Harness (MB991613) connector No. 5.
Disconnect SRS-ECU connector C-122 and connect SRS check harness
connector No. 3 to C-122. Check terminal No. 20 and 21 for continuity
to ground. If there is no continuity, go to next step. If there is
continuity, go to step 4).
3) Check connector C-122 and repair if necessary. If
connector is okay, check for trouble symptoms. If fault still exists,
check harness wire between SRS-ECU and ground, and repair if
necessary.
4) Measure SRS check harness connector No. 5. Disconnect SRS-
ECU connector C-122 and connect SRS harness check connector No. 3 to
C-122. Connect negative battery cable and turn ignition switch to ON
position. Connect terminal No. 15 to body ground. If SRS warning light
comes on, replace SRS-ECU. See SRS AIR BAG CONTROL UNIT (ECU) under
REMOVAL & INSTALLATION. If SRS warning light does not come on, inspect
for blown bulb and repair if necessary. If bulb is okay, check
connector C-04, C-11, C-96, and C-101, and repair if necessary. If
connectors are okay, check for trouble symptoms. If fault still
exists, check harness wire between SRS-ECU and ignition switch IG1,
and repair if necessary. If harness wire is okay, replace combination