1998 MITSUBISHI MONTERO transmission

CRUISE CONTROL SYSTEM
1998 Mitsubishi Montero
1998 ACCESSORIES & EQUIPMENT
Mitsubishi - Cruise Control Systems
Montero
DESCRIPTION & OPERATION
WARNING: Deactivate air bag system before performing any service
operation. See AIR BAG RESTRAINT SYSTEMS article. Do not
apply electrical power to any component on steering column
without first deactivating air bag system. Air bag may
deploy.
Cruise control system is electronically and vacuum
controlled. System components include a control unit, actuator, vacuum
pump, cruise control switch, clutch pedal position switch (M/T),
cruise indicator light, diode, Park/Neutral (P/N) switch (A/T),
stoplight switch, vehicle speed sensor and A/T control unit (if
equipped).
System has self-diagnostic capability. When self-diagnostic
mode is activated, each switch and sensor is checked for defects. When
cruise control system has been canceled without using a normal cancel
method, a trouble code will be set and stored in control unit. Trouble
codes can be retrieved to help determine which circuit is
malfunctioning.
COMPONENT LOCATIONS
COMPONENT LOCATIONS TABLE








\









\









\









\









\









\






Component Location
Cruise Control ECU .............. Behind Dash, On Steering
Column Bracket
Data Link Connector (DLC) ....... Under Left Side Of Dash,
Near Steering Column
Vehicle Speed Sensor ........... On Speedometer Assembly &
On Transmission
Throttle Position Sensor ........ Mounted On Throttle Body









\









\









\









\









\









\






ADJUSTMENTS
CRUISE CONTROL CABLE
Remove link protector. Loosen lock nut. Hold link "A" so that
it touches link "B". Adjust free play by turning adjusting nut until
free play is.04-.08" (1-2 mm). Tighten lock nut. See Fig. 1 or 2.

* PLEASE READ THIS FIRST *
NOTE: For further trouble shooting information, see INPUT
INSPECTION CHART. See Fig. 3. See
INSPECTION CHART FOR TROUBLE SYMPTOMS table under SYMPTOM
TESTS.
PRELIMINARY CHECKS
Inspect vacuum pump, linkage assembly, actuator, cables and
vacuum hoses. Ensure linkage and cables move smoothly. Ensure cables
do not have excessive slack or tension.
CRUISE CONTROL SWITCH FUNCTION TEST
NOTE: If vehicle speed decreases about 9 MPH less than the set
speed, set speed will be canceled. Speed will not set beyond
system limit of 124 MPH.
1) Cruise control switch is part of multifunction switch
mounted on steering column. To operate cruise control system, turn
ignition on. Turn cruise control switch to ON position. Ensure switch
indicator light comes on.
2) With cruise control switch in ON position, drive vehicle
at least 25 MPH. Press and release SET button. Vehicle speed should
stay at set speed. Instrument cluster cruise indicator light should
come on. To increase set speed, turn control switch to RESUME position
and hold until new set speed is reached.
3) To lower set speed, press SET button and hold until new
set speed is reached. To return to set speed after cancellation, move
resume switch to ON position. Vehicle speed should return to previous
setting before cancellation. Set speed should cancel when any of the
following occurs:
* Brake pedal is depressed.
* Cruise control main switch is turned to OFF position.
* Ignition switch is turned to OFF position.
* Transmission is shifted to Neutral.
SYSTEM CANCELS OR WILL NOT RESET AFTER CANCELLATION
1) Check for trouble codes. See RETRIEVING CODES under SELF-
DIAGNOSTIC SYSTEM. If no trouble codes are stored, ensure cruise
control can be set.
2) If cruise control can be set, system may have canceled due
to driving on steep hills, or a loose wiring connection. If cruise
control still cannot be set, perform SYSTEM INPUT TESTS under SYMPTOMS
TESTS.
3) If SYSTEM INPUT TESTS check okay, check vacuum pump
circuit. See CODE 11 under DIAGNOSTIC TESTS. If SYSTEM INPUT TESTS do
not check okay, see INPUT INSPECTION CHART. See Fig. 3.
SYMPTOM TESTS
SYSTEM INPUT TESTS
1) System input tests should be performed if no trouble codes
are stored when performing RETRIEVING CODES under SELF-DIAGNOSTIC
SYSTEM. System input tests cycle each cruise control switch and
sensor.

Fig. 11: Identifying Cruise Control Circuit Connector Terminals:
Combination Meter Connector (C-12)
Courtesy of Mitsubishi Motor Sales of America
Fig. 12: Identifying Cruise Control Circuit Connector Terminals:
Dash Harness/Transmission Harness Connector (C-124)
Courtesy of Mitsubishi Motor Sales of America
Fig. 13: Identifying Cruise Control Circuit Connector Terminals:
Cruise Control ECU Connector (C-50)
Courtesy of Mitsubishi Motor Sales of America
Fig. 14: Identifying Cruise Control Circuit Connector Terminals:
Stoplight Switch Connector (C-55)
Courtesy of Mitsubishi Motor Sales of America

An open circuit in output signal circuit in Neutral range is
likely reason for malfunction. Probable causes are:
* Malfunction of park/neutral switch.
* Malfunction of connector.
* Malfunction of harness.
* Malfunction of cruise control ECU.
Check condition of park/neutral switch connector B-08, dash
harness/transmission harness connector C-124, cruise control ECU
connector C-50 and joint connector C-130. Repair as necessary. If
connectors are okay and malfunction remains, check harness between
park/neutral switch and cruise control ECU. Repair as necessary. If
harness is okay, replace cruise control ECU.
Test No. 6
An open circuit in circuit inside CANCEL switch is likely
caused by a malfunction in cruise control switch. Replace cruise
control switch.
Test No. 7
Because of an open circuit in battery back-up circuit system,
fail-safe function prevents diagnostic trouble codes from being
memorized and displayed even though cruise control is canceled.
Probable causes are:
* Malfunction of connector.
* Malfunction of harness.
* Malfunction of cruise control ECU.
1) Disconnect cruise control ECU connector C-50. See Fig. 13.
At harness side of connector, measure voltage between terminal No. 16
and ground. If battery voltage is present, go to next step. If battery
voltage is not present, check and repair IOD connector A-09X, joint
connector C-132, junction block connector C-81 and junction block
connector C-93 as necessary. See Figs. 4, 16, 19, 20, 26 and 30. If
connectors are okay and malfunction remains, check harness between
cruise control ECU and power supply. Repair as necessary.
2) Check condition of cruise control ECU connector C-50.
Repair as necessary. If connector is okay and malfunction remains,
replace cruise control ECU.
Test No. 8
A malfunction of switches or fail-safe function cancelling
cruise control may be present. Probable causes are:
* Malfunction of cruise control main switch.
* Malfunction of cruise control switch.
* Malfunction of clockspring.
* Malfunction of harnesses or connectors.
* Malfunction of park/neutral position switch.
* Malfunction of cruise control ECU.
1) Attach scan tool to DLC. If scan tool can communicate with
cruise control, go to next step. If scan tool cannot communicate with
cruise control, go to TEST NO. 2.
2) If input switch inspection is possible with scan tool, go
to next step. If input switch inspection is not possible, go to TEST
NO. 3.
3) If input switch Code 21, 22 or 27 are still displayed,
replace cruise control main switch. If codes are no longer displayed,
go to next step.
4) If input switch Code 23 is still displayed, go to TEST NO.

Main Switch
1) In each switch position, continuity should be present
between terminals No. 2 and 7 for switch illumination. See Fig. 8.
When switch is moved to Neutral position, continuity should be present
between terminals No. 1 and 4.
2) When switch is moved to ON position, continuity should be
present between terminals No. 4 and 5. Connect battery voltage to
terminal No. 5 and ground terminal No. 4.
3) Battery voltage should be present on terminal No. 1 when
main switch is moved to ON position. Replace main switch if it does
not test as specified.
PARK/NEUTRAL SWITCH TEST
Disconnect switch connector. Shift transmission into Neutral
position. Continuity should be present between terminals No. 5
(Black/Blue wire) and No. 6 (Blue/Black wire). See Fig. 7. If
continuity is not present, adjust park/neutral switch. If switch is
adjusted properly, replace switch.
VACUUM PUMP TEST
1) Disconnect vacuum pump connector A-105. Resistance should
be 50-60 ohms between terminals No. 1 and 2 and terminals No. 1 and 3.
See Fig. 6 . Ensure solenoid valve makes operating noise when battery
voltage is applied between terminals No. 1 and 2 and terminals No. 1
and 3.
2) If solenoid valve does not operate, replace vacuum pump
assembly. Apply battery voltage and ground between terminals No. 1 and
4. Motor should operate. Replace vacuum pump if motor does not
operate.
VEHICLE SPEED SENSOR TEST
Remove speed sensor from transmission. Connect speed sensor,
resistor (3000-10,000 ohms) and battery. See Fig. 34. Using a
voltmeter, ensure voltage pulses on and off 4 times per revolution of
speedometer shaft. Replace sensor if voltage is not as specified.
Fig. 34: Testing Vehicle Speed Sensor
Courtesy of Mitsubishi Motor Sales of America
SELF-DIAGNOSTIC SYSTEM

D - ADJUSTMENTS
1998 Mitsubishi Montero
1998 ENGINE PERFORMANCE
Mitsubishi - On-Vehicle Adjustments
Diamante, Eclipse, Galant, Mirage, Montero, Montero Sport,
3000GT
ENGINE MECHANICAL
Before performing any on-vehicle adjustments to fuel or
ignition system, ensure engine mechanical condition is okay (i.e.,
engine compression).
VALVE CLEARANCE
VALVE ADJUSTMENT
NOTE: All models use hydraulic valve lifters. Adjustment is not
required.
CHECKING HYDRAULIC VALVE LIFTERS
1) Warm engine to normal operating temperature. Remove valve
cover. Position cylinder No. 1 at TDC on compression stroke. On 4-
cylinder engines, check intake rockers on cylinders No. 1 and 2. Check
exhaust rockers on cylinders No. 1 and 3. On V6 engines, check intake
rockers on cylinders No. 1, 5 and 6. Check exhaust rockers on
cylinders No. 1, 2 and 3.
2) Push downward on end of rocker arm, above lash adjuster.
Rotate crankshaft 360 degrees. On 4-cylinder engines, check intake
rockers on cylinders No. 3 and 4. Check exhaust rockers on cylinders
No. 2 and 4. On V6 engines, check intake rockers on cylinders No. 2, 3
and 4. Check exhaust rockers on cylinders No. 4, 5 and 6. If lash
adjuster is normal, it will feel solid.
3) If lash adjuster moves downward easily when pushed,
replace adjuster. If lash adjuster feels soft or spongy, air has
probably entered lash adjuster. If this occurs, check engine oil
level. If engine oil level is okay, check oil screen and oil screen
gasket for damage.
4) After repairing cause of air ingestion, warm engine to
operating temperature. Drive vehicle at low speed for approximately 5
minutes. Turn engine off for a few minutes.
5) Restart engine and drive at low speed for approximately 5
minutes. Repeat this step several times for about one hour. This helps
remove air from engine oil.
IGNITION TIMING
NOTE: Perform all checks with engine at normal operating
temperature, cooling fan and accessories off, transmission
in Park or Neutral, and front wheels in straight-ahead
position. Ignition timing check procedure for Eclipse 2.0L
non-turbo not available from manufacturer at time of
publication.
Diamante
1) Ignition timing is controlled by Powertrain Control Module
(PCM) and is not adjustable. Manufacturer provides procedure for
checking timing. DO NOT attempt to adjust ignition timing by rotating

is 600-700 RPM. Turn engine off. Curb idle speed is automatically
controlled by Idle Air Control (IAC) system. If curb idle speed is not\
as specified, see DTC P0505 in G - TESTS W/CODES article.
4) Disconnect waterproof female connector from Brown ignition
timing check connector. See Fig. 4. Using a jumper wire, ground
ignition timing check terminal to read basic ignition timing. Using
timing light, read basic ignition timing value. See
IGNITION TIMING SPECIFICATIONS table. If basic ignition timing is
within specification, go to next step. If basic ignition timing is not
within specification, see DTC P0335 in G - TESTS W/CODES article.
5) Remove jumper wire to read actual ignition timing. Using
timing light, read actual ignition timing value. If actual ignition
timing is not within specification, see DTC P0335 in G - TESTS W/CODES
article.
All Other Models
1) Ignition timing is controlled by Powertrain Control Module
(PCM) and is not adjustable. Manufacturer provides procedure for
checking timing. On models with distributor, DO NOT attempt to adjust
ignition timing by rotating distributor.
2) Connect scan tool to Data Link Connector (DLC). DLC is
located below dash, near steering column. See Fig. 2. Install a timing
light. Start engine and allow it to idle.
3) Using scan tool, read curb idle speed (RPM). Ensure curb
idle speed is about 750 RPM. Turn engine off. Curb idle speed is
automatically controlled by Idle Air Control (IAC) system. If curb
idle speed is not as specified, see DTC P0505 in G - TESTS W/CODES
article.
CAUTION: MFI system actuator test must be cancelled or test will
continue to run for 27 minutes. Driving vehicle under this
condition may damage engine.
4) Using scan tool, select MFI SYSTEM ACTUATOR TEST, then
select item 17 (BASIC IGNITION TIMING). Read basic ignition timing
value. See IGNITION TIMING SPECIFICATIONS table. If basic ignition
timing is within specification, go to next step. If basic ignition
timing is not within specification, cancel MFI system actuator test.
See DTCS P0100 (except Mirage 1.5L), P0105, P0115 and P0335 in G -
TESTS W/CODES article.
5) Read actual ignition timing value. If actual ignition
timing is not within specification, cancel MFI system actuator test.
See DTCS P0100 (except Mirage 1.5L), P0105, P0115 and P0335 in G -
TESTS W/CODES article.
IDLE SPEED & MIXTURE
* PLEASE READ THIS FIRST *
NOTE: Perform adjustments with engine at normal operating
temperature, cooling fan and accessories off, transmission
in Park or Neutral, and front wheels in straight-ahead
position.
BASIC IDLE SPEED
NOTE: Basic idle speed adjustment information on Eclipse 2.0L
non-turbo engine is not available from manufacturer at time
of publication.
3000GT
1) Ensure vehicle is at normal operating temperature with all

lights, cooling fan and accessories off. Shift transmission into
Neutral or Park position.
2) If not using scan tool, go to next step. Connect scan tool
to Data Link Connector (DLC). DLC is located below dash, near steering\
column. See Fig. 2. Go to step 5).
3) On DOHC models, insert a paper clip in engine speed
detection connector. See Fig. 3. On SOHC models, insert paper clip in
noise filter connector. See Fig. 5. On all models, connect a
tachometer to paper clip.
4) Connect a jumper wire between ground and Data Link
Connector (DLC) terminal No. 1. See Fig. 2. Disconnect waterproof
female connector from Brown ignition timing check connector. See
Fig. 4 . Using a jumper wire, ground ignition timing check terminal.
5) Start engine and allow it to idle. Check basic idle speed.
See IDLE SPEED SPECIFICATIONS table. On DOHC models, multiply
tachometer reading by 3 to obtain actual basic idle speed. If idle
speed is not within specification, turn engine speed adjusting screw
until correct engine speed is obtained. See Fig. 6. Access to speed
adjusting screw is obtained by removing rubber plug on throttle body.
6) If idle speed cannot be lowered by turning engine speed
adjusting screw, determine if Throttle Position (TP) sensor has been
moved. Adjust TP sensor if necessary. See TP SENSOR ADJUSTMENT under
THROTTLE POSITION (TP) SENSOR. If TP sensor is okay, replace throttle
body.
Fig. 6: Adjusting Idle Speed (Typical)
Courtesy of Mitsubishi Motor Sales of America
IDLE SPEED SPECIFICATIONS TABLE









\









\









\









\









\









\