1998 MITSUBISHI MONTERO head
[x] Cancel search: headPage 441 of 1501
Condition Code Procedure
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A ... Require repair or replacement
of hardware.
Broken .................. A ............ Require replacement.
Leaking (hydraulic
mount) ................. A ............ Require replacement.
Mounting hole worn,
affecting performance .. A ............ Require replacement.
Mounting hole worn, not
affecting performance .. .. ........ No service suggested or
required.
Rubber deteriorated,
affecting performance .. A ............ Require replacement.
Rubber deteriorated, not
affecting performance .. .. ........ No service suggested or
required.
Threads damaged ......... A .. Require repair or replacement.
Threads stripped (threads
missing) ............... A ............ Require replacement.
\
\
\
\
\
\
\
ODOMETER DRIVES (MECHANICAL)
See SPEEDOMETER/ODOMETER DRIVES (MECHANICAL) .
ODOMETER HEADS (MECHANICAL)
See SPEEDOMETER/ODOMETER HEADS (MECHANICAL) .
OIL PANS
See TRANSMISSION PANS .
PANS
See TRANSMISSION PANS .
PILOT HOLES
See DOWEL PINS, GUIDES AND PILOT HOLES .
PRESSURE PLATES
PRESSURE PLATE INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Balance weight missing .. C ............ Require replacement.
Broken .................. A ............ Require replacement.
Contact surface
distorted .............. B ............ Require replacement.
Cracks .................. B ............ Require replacement.
Fingers bent ............ A ............ Require replacement.
Hard spots .............. B ............ Require replacement.
Page 446 of 1501
Threads damaged ......... A .. Require repair or replacement.
Threads stripped (threads
missing) ............... A ............ Require replacement.
Worn close to the end of
its useful life ........ 1 ............ Suggest replacement.
Worn, affecting
performance ............ A ............ Require replacement.
(1) - Inoperative includes intermittent operation.
\
\
\
\
\
\
\
SPEEDOMETER/ODOMETER HEADS (MECHANICAL)
SPEEDOMETER/ODOMETER HEAD (MECHANICAL) INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A ... Require repair or replacement
of hardware.
Lens broken ............. A ........... ( 1) Require repair or
replacement.
Lens cloudy ............. 2 ........... ( 1) Suggest repair or
replacement.
Lens missing ............ C ........... ( 1) Require repair or
replacement.
Malfunctioning .......... A ........... ( 2) Require repair or
replacement.
Noisy ................... 2 .. Suggest repair or replacement.
Threads damaged ......... A .. Require repair or replacement.
Threads stripped (threads
missing) ............... A ............ Require replacement.
( 1) - If lens is available as a separate part, require
replacement of lens only.
( 2) - Includes inoperative, intermittent operation, failure
to perform all functions, out of OEM specification, or
out of range.
\
\
\
\
\
\
\
SPEEDOMETERS AND ODOMETERS (ELECTRONIC)
SPEEDOMETER AND ODOMETER (ELECTRONIC) INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A ... Require repair or replacement
of hardware.
Connector broken ........ A .. Require repair or replacement.
Connector (Weatherpack
Page 447 of 1501
type) leaking .......... A .. Require repair or replacement.
Connector melted ........ A ........... (1) Require repair or
replacement.
Connector missing ....... C ............ Require replacement.
Leaking ................. A ............ Require replacement.
Lens broken ............. A ........... ( 2) Require repair or
replacement.
Lens cloudy ............. 2 ........... ( 2) Suggest repair or
replacement.
Lens missing ............ C ........... ( 2) Require repair or
replacement.
Malfunctioning .......... A ........... ( 3) Require repair or
replacement.
Mechanical head noisy ... 2 .. Suggest repair or replacement.
Terminal broken ......... A .. Require repair or replacement.
Terminal burned, affecting
performance ............ A ........... ( 1) Require repair or
replacement.
Terminal burned, not
affecting performance .. 2 .. Suggest repair or replacement.
Terminal corroded,
affecting performance .. A .. Require repair or replacement.
Terminal corroded, not
affecting performance .. 2 .. Suggest repair or replacement.
Terminal loose, affecting
performance ............ B .. Require repair or replacement.
Terminal loose, not
affecting performance .. 1 .. Suggest repair or replacement.
( 1) - Determine cause and correct prior to repair or
replacement of part.
( 2) - If lens is available as a separate part, require
replacement of lens only.
( 3) - Includes inoperative, intermittent operation, failure
to perform all functions, out of OEM specification,
or out of range.
\
\
\
\
\
\
\
SWITCHES
SWITCH INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A ... Require repair or replacement
of hardware.
Binding, affecting
performance ............ A .. Require repair or replacement.
Binding, not affecting
performance ............ 2 .. Suggest repair or replacement.
Broken .................. A .. Require repair or replacement.
Burned, affecting
performance ............ A ........... ( 1) Require repair or
replacement.
Burned, not affecting
performance ............ 2 ........... ( 1) Suggest repair or
Page 466 of 1501
Headlight Relay In engine compartment
relay box.
Headlight Washer Relay On bracket, behind left side
of dash.
Horn Relay Left front of engine
compartment.
Ignition Key Hole Illumination Light
Timer Behind center console.
Intermittent Wiper Relay (Rear Wiper) In passenger compartment
relay box.
Intermittent Wiper Relay (Windshield
Wiper) Built-in to steering column
switch.
Power Window Relay In passenger compartment
relay box.
Starter Relay Behind center console.
Page 470 of 1501
Door Lock Control Unit Behind left side of dash.
ELC 4-Speed Automatic Transmission
Control Module Behind left side of dash.
Engine Control Module (ECM) Behind right kick panel.
Keyless Entry Control Unit Behind right side quarter
panel.
Rear Differential Lock Control Unit Mounted on top of left rear
wheelwell.
SRS Air Bag Control Unit Behind center of dash.
Sun Roof Control Unit On center of roof, behind
sun roof.
Variable Shock Absorber Control Unit Behind left rear wheelwell,
behind quarter panel.
4WD Indicator Control Unit Behind center of dash.
\
\
\
\
\
\
\
MOTORS
\
\
\
\
\
\
\
Component Component Location \
\
\
\
\
\
\
Blower Motor Behind right side of dash.
Condenser Fan Motor On left front of engine
compartment.
Fuel Pump In fuel tank.
Headlight Washer Motor Right side of engine
compartment, in washer fluid
reservoir.
Idle Air Control Motor On throttle body.
Motor Antenna Rear of right front wheelwell.
Rear Differential Lock Air Pump On left rear of vehicle.
Rear Washer Motor In rear of cargo area.
Rear Wiper Motor On center of tailgate.
Sun Roof Motor On center of roof, behind
sun roof.
Windshield Washer Motor Bottom of windshield washer
reservoir.
Windshield Wiper Motor On left side of firewall.
\
\
\
\
\
\
\
SENDING UNITS & SENSORS
Page 473 of 1501
Outside Air Temperature Sensor Below left headlamp.
Park/Neutral Position Sensor On left side of transmission.
Throttle Position Sensor On throttle body.
Vehicle Speed Sensor (VSS) On transmission tailshaft.
Volume Airflow Sensor In air cleaner duct (includes
intake air temperature sensor
& barometric pressure sensor).
\
\
\
\
\
\
\
SOLENOIDS & SOLENOID VALVES
\
\
\
\
\
\
\
Component Component Location \
\
\
\
\
\
\
ABS Hydraulic Unit (w/Built-In
Solenoid Valve) In right rear corner of engine
compartment.
Cruise Control Actuator (w/Built-In
Control Valve & Release Valve)
(Calif.) In right rear of engine
compartment.
Cruise Control Actuator (w/Built-In
Control Valve & Release Valve)
(Federal) In left rear of engine
compartment.
EGR Solenoid In right rear of engine
compartment.
ELC 4-Speed Automatic Transmission
Control Solenoid Inside transmission.
Evaporative Emission Purge Solenoid On front of engine.
Evaporative Emission Ventilation
Solenoid In left rear of engine
compartment.
Solenoid Valves "A" & "B" In right side of engine
compartment.
\
\
\
\
\
\
\
SWITCHES
\
\
\
\
\
\
\
Component Component Location \
\
\
\
\
\
\
A/T Fluid Temperature Switch On left side of transmission.
Brake Fluid Level Switch In brake master cylinder
reservoir.
Center Differential Lock Detection
Switch On transfer case.
Page 479 of 1501
* ELECTRICAL SYSTEM UNIFORM INSPECTION GUIDELINES *
1998 Mitsubishi Montero
GENERAL INFORMATION
Electrical System Motorist Assurance Program
Standards For Automotive Repair
All Makes and Models
INTRODUCTION TO MOTORIST ASSURANCE PROGRAM (MAP)
CONTENTS
OVERVIEW OF MOTORIST ASSURANCE PROGRAM
OVERVIEW OF SERVICE REQUIREMENTS & SUGGESTIONS
ACTUATOR MOTORS (SOLENOIDS) (ELECTRIC)
ACTUATOR MOTORS (VACUUM)
AIR BAGS
ALTERNATORS AND GENERATORS
AMPLIFIERS
ANTENNAS
BATTERIES
BATTERY CABLES
BATTERY CABLES
BATTERY HOLD DOWN HARDWARE
BATTERY TRAYS AND HOLD DOWN HARDWARE
BATTERY WIRES
BELTS
BULB SOCKETS
BULBS, SEALED BEAMS AND LEDS
CD PLAYERS
CIGARETTE LIGHTER ASSEMBLIES
CIRCUIT BREAKERS
CLUTCH SWITCHES
CONNECTORS
CONTROL MODULES
CRUISE CONTROL BRAKE SWITCHES
CRUISE CONTROL CABLES
CRUISE CONTROL CLUTCH SWITCHES
CRUISE CONTROL LINKAGES AND CABLES
CRUISE CONTROL RESERVOIRS
CRUISE CONTROL TUBES
CRUISE CONTROL VACUUM DUMP RELEASE VALVES
CRUISE CONTROL VACUUM HOSES, TUBES AND RESERVOIRS
CRUISE CONTROL VEHICLE SPEED SENSORS
DEFOGGERS
DEFROSTERS
DELAYS
DIMMERS
ELECTRIC HEATERS
EQUALIZERS
FUSE BLOCKS
FUSE BOXES AND BLOCKS
FUSES, FUSIBLE LINKS AND CIRCUIT BREAKERS
FUSIBLE LINKS
GAUGES
GENERATORS
GROUND CABLES AND STRAPS
GROUND STRAPS
HEADLIGHT ADJUSTERS
HEATING ELEMENTS (DEFROSTERS, DEFOGGERS, ELECTRIC HEATERS AND SEATS)
HORNS AND SIRENS
Page 503 of 1501
![MITSUBISHI MONTERO 1998 Service Manual \
\
\
\
\
\
\
FUSIBLE LINKS
See FUSES, FUSIBLE LINK](/manual-img/19/57333/w960_57333-502.png "MITSUBISHI MONTERO 1998 Service Manual \
\
\
\
\
\
\
FUSIBLE LINKS
See FUSES, FUSIBLE LINK")
\
\
\
\
\
\
\
FUSIBLE LINKS
See FUSES, FUSIBLE LINKS AND CIRCUIT BREAKERS .
GAUGES
NOTE: Includes odometers, speedometers and tachometers (except
cable-driven).
GAUGE INSPECTION
\
\
\
\
\
\
\
Condition Code Procedure
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A ... Require repair or replacement
of hardware.
Connector broken ........ A .. Require repair or replacement.
Connector (Weatherpack
type) leaking .......... A .. Require repair or replacement.
Connector melted ........ A ........... ( 1) Require repair or
replacement.
Connector missing ....... C ............ Require replacement.
Leaking ................. A ............ Require replacement.
Lens broken ............. A ........... ( 2) Require repair or
replacement.
Lens cloudy ............. 2 ........... ( 2) Suggest repair or
replacement.
Lens missing ............ C ........... ( 2) Require repair or
replacement.
Malfunctioning .......... A ........... ( 3) Require repair or
replacement.
Mechanical head noisy ... 2 .. Suggest repair or replacement.
Terminal broken ......... A .. Require repair or replacement.
Terminal burned, affecting
performance ............ A ........... ( 1) Require repair or
replacement.
Terminal burned, not
affecting performance .. 2 .. Suggest repair or replacement.
Terminal corroded,
affecting performance .. A .. Require repair or replacement.
Terminal corroded, not
affecting performance .. 2 .. Suggest repair or replacement.
Terminal loose, affecting
performance ............ B .. Require repair or replacement.
Terminal loose, not
affecting performance .. 1 .. Suggest repair or replacement.
( 1) - Determine cause and correct prior to repair or
replacement of part.
( 2) - If lens is available as a separate part, require
replacement of lens only.
( 3) - Includes inoperative, intermittent operation, failure
to perform all functions, out of OEM specification,
or out of range.
\
\
\
\
\
\
\