1998 MITSUBISHI MONTERO brake

 Front Wheel  All  Multipurpose Grease 

Bearings   NLGI Grade 2 Or 

  Equivalent 
\b
\
 \
\
\
 \
\
\



Door Hinges, All  Engine Oil 

Back Door   

Hinges   
\b
\
 \
\
\
 \
\
\



A/C  All  HFC-134a 

Refrigerant   
\b
\
 \
\
\
 \
\
\



Manual  All API Classification GL-4

Transmission   SAE 75W-85W Or 75W-90 
\b
\
 \
\
\
 \
\
\



Automatic  All  "ATF DEXRON II" Or 

Transmission   Equivalent 
\b
\
 \
\
\
 \
\
\



Brake Fluid  All  DOT 3 Or DOT 4 
\b
\
 \
\
\
 \
\
\



Rear Axle  All API Classification GL-5

  Or Higher (
2) 
\b
\
\
\
\
\
\
\





(
1) - SAE 5W-30 engine oil is preferred. SAE 10W-30 may be used if 

the Ambient Temperature is above 0 F (-18 C). 

(
2) - SAE90, 85W-90, 80W-90 may be used in temperatures above 

-10 F (-23 C). SAE 80W, 80W-90 may be used in temperatures 

from -30 F (-34 C) to -10 F (-23 C). SAE 75W may be used 

in temperatures below -30 F (-34 C). 
\f
\
\
\
\
\
\
\


FLUID CAPACITIES
FLUID CAPACITIES TABLE ( 1)
\
\
\
\
\
\
\
 
Item  Condition  Specification 
\b
\
 \
\
\
 \
\
\



Engine Oil  Oil Pan  4.5 Qts. (4.3L) 

(
1) \b \
\
\
 \
\



 Oil Filter  0.32 Qts. (0.3L) 

\b
\
\
\
 \
\



 Oil Cooler  0.32 Qts. (0.3L) 
\b
\
 \
\
\
 \
\
\



Power  Drained  1.1 Qts. (1.0L) 

Steering   
\b
\
 \
\
\
 \
\
\



Automatic  Drained  8.9 Qts. (8.5L) 

Transmission   
\b
\
 \
\
\
 \
\
\



Manual  Drained  3.3 Qts. (3.2L) 

Transmission   
\b
\
 \
\
\
 \
\
\



Transfer Case Drained  2.6 Qts. (2.5L) 
\b
\
 \
\
\
 \
\
\



Front Axle  Drained  1.3 Qts. (1.2L) 
\b
\
 \
\
\
 \
\
\



Rear Axle  Drained  3.3 Qts. (3.2L) 
\b
\
 \
\
\
 \
\
\



A/C  Drained  27 oz (760 g) 

Refrigerant   
\b
\
 \
\
\
 \
\
\



Fuel Tank  Capacity  24 gal (92L) 

IGNITION SWITCH
Removal & Installation
1) Remove upper and lower steering column covers. Disconnect
harness connector from ignition switch. Using hacksaw, cut slots in
bolt heads of lock assembly. Using screwdriver, remove bolts and lock
assembly.
2) To install, reverse removal procedure. Tighten new bolts
until heads of bolts sheer off.
STEERING COLUMN
WARNING: Failure to follow air bag service precautions may result in
air bag deployment and personal injury. See AIR BAG SERVICE
PRECAUTIONS. Follow all service precautions before
attempting repairs. After component replacement, perform a
system operational check to ensure proper system operation.
CAUTION: Applying excessive pressure or causing impact to steering
shaft during service may cause column to collapse. Before
removing steering column, ensure wheels are in
straight-ahead position. Note steering wheel location for
installation reference.
Removal
1) Remove steering wheel. Remove combination switch and
ignition switch (if necessary). See STEERING WHEEL under
REMOVAL & INSTALLATION .
2) Remove lower instrument panel cover and air duct.
Disconnect all electrical connections. Disconnect brake pedal return
spring (if equipped). Disconnect gearshift control cable.
3) Remove bolts for dust cover at firewall. Remove bolt from
clamp at steering gear. Remove steering column bolts and remove
steering column.
Installation
To install, reverse removal procedure. Apply sealant (3M ATD
8663) to dust cover bolts before installing. Tighten bolts to
specification. See TORQUE SPECIFICATIONS .
OVERHAUL
STEERING COLUMN
WARNING: Failure to follow air bag service precautions may result in
air bag deployment and personal injury. See AIR BAG SERVICE
PRECAUTIONS. Follow all service precautions before
attempting repairs. After component replacement, perform a
system operational check to ensure proper system operation.
NOTE: Vehicle steering column is not repairable. See below for
joint assembly and steering lock removal and installation.
Disassembly
Remove steering column from vehicle. See STEERING COLUMN
under REMOVAL & INSTALLATION . Remove clamp bolt from joint assembly.
See Fig. 1 . Remove assembly. Remove lower boot, upper boot and dust
cover from joint assembly. To remove steering lock, use a hacksaw to
cut bolts at steering lock bracket side. Remove steering lock and
bracket.

TIE ROD ENDS (INNER AND OUTER)
TRACK BARS
TRAILING ARMS
WHEEL BEARINGS, RACES AND SEALS
Wheel Alignment
WHEEL ALIGNMENT
Wheels and Tires
TIRES
VALVE STEMS
WHEEL ATTACHMENT HARDWARE
WHEELS (RIMS)
MOTORIST ASSURANCE PROGRAM (MAP)
OVERVIEW
The Motorist Assurance Program is the consumer outreach
effort of the Automotive Maintenance and Repair Association, Inc.
(AMRA). Participation in the Motorist Assurance Program is drawn from
retailers, suppliers, independent repair facilities, vehicle
manufacturers and industry associations.
Our organization's mission is to strengthen the relationship
between the consumer and the auto repair industry. We produce
materials that give motorists the information and encouragement to
take greater responsibility for their vehicles-through proper,
manufacturer-recommended, maintenance. We encourage participating
service and repair shops (including franchisees and dealers) to adopt
1) a Pledge of Assurance to their Customers and 2) the Motorist
Assurance Program Standards of Service. All participating service
providers have agreed to subscribe to this Pledge and to adhere to the
promulgated Standards of Service demonstrating to their customers that
they are serious about customer satisfaction.
These Standards of Service require that an inspection of the
vehicle's (problem) system be made and the results communicated to the\
customer according to industry standards. Given that the industry did
not have such standards, the Motorist Assurance Program successfully
promulgated industry inspection communication standards in 1994-95 for
the following systems: Exhaust, Brakes, ABS, Steering and Suspension,
Engine Maintenance and Performance, HVAC, and Electrical Systems.
Further, revisions to all of these inspection communication standards
are continually re-published. In addition to these, standards for
Drive Train and Transmissions have recently been promulgated.
Participating shops utilize these Uniform Inspection & Communication
Standards as part of the inspection process and for communicating
their findings to their customers.
The Motorist Assurance Program continues to work
cooperatively and proactively with government agencies and consumer
groups toward solutions that both benefit the customer and are
mutually acceptable to both regulators and industry. We maintain the
belief that industry must retain control over how we conduct our
business, and we must be viewed as part of the solution and not part
of the problem. Meetings with state and other government officials
(and their representatives), concerned with auto repair and/or
consumer protection, are conducted. Feedback from these sessions is
brought back to the association, and the program adjusted as needed.
To assure auto repair customers recourse if they were not
satisfied with a repair transaction, the Motorist Assurance Program
offers mediation and arbitration through MAP/BBB-CARE and other non-

profit organizations. MAP conducted pilot programs in twelve states
before announcing the program nationally in October, 1998. During the
pilots, participating repair shops demonstrated their adherence to the
Pledge and Standards and agreed to follow the UICS in communicating
the results of their inspection to their customers. To put some
"teeth" in the program, an accreditation requirement for shops was
initiated. The requirements are stringent, and a self-policing method
has been incorporated which includes the "mystery shopping" of
outlets.
We welcome you to join us as we continue our outreach... with
your support, both the automotive repair industry and your customers
will reap the benefits. Please visit MAP at our Internet site www.
motorist.org or contact us at:
1444 I Street, NW Suite 700
Washington, DC 20005
Phone (202) 712-9042 Fax (202) 216-9646
January 1999
MAP UNIFORM INSPECTION GENERAL GUIDELINES
OVERVIEW OF SERVICE REQUIREMENTS & SUGGESTIONS
It is MAP policy that all exhaust, brake, steering,
suspension, wheel alignment, drive-line, engine performance and
maintenance, and heating, ventilation and air conditioning, and
electrical services be offered and performed under the standards and
procedures specified in these sections.
Before any service is performed on a vehicle, an inspection
of the appropriate system must be performed. The results of this
inspection must be explained to the customer and documented on an
inspection form. The condition of the vehicle and its components will
indicate what services/part replacements may be "Required" or
"Suggested". In addition, suggestions may be made to satisfy the
requests expressed by the customer.
When a component is suggested or required to be repaired or
replaced, the decision to repair or replace must be made in the
customer's best interest, and at his or her choice given the options
available.
This section lists the various parts and conditions that
indicate a required or suggested service or part replacement.
Although this list is extensive, it is not fully inclusive. In
addition to this list, a technician may make a suggestion. However,
any suggestions must be based on substantial and informed experience,
or the vehicle manufacturer's recommended service interval and must be
documented.
Some conditions indicate that service or part replacement is
required because the part in question is no longer providing the
function for which it is intended, does not meet a vehicle
manufacturer's design specification or is missing.
Example:
An exhaust pipe has corroded severely and has a hole in it
through which exhaust gases are leaking. Replacement of the
exhaust pipe in this case is required due to functional
failure.
Example:
A brake rotor has been worn to the point where it measures
less than the vehicle manufacturer's discard specifications.
Replacement of the rotor is required because it does not meet
design specifications.

Stud loose in
taper hole ............. A ........... (7) Require repair or
replacement.
Taper hole elongated .... A ........ ( 8) Require replacement.
Threads damaged ......... A .. Require repair or replacement.
Threads stripped (threads
missing) ............... A ........ ( 7) Require replacement.
Wear exceeds
manufacturer's
specifications .......... B ............ Require replacement.
( 1) - If greaseable, grease joint. If problem persists or
joint is non-greaseable, require replacement.
( 2) - Cracked grease boot will allow contaminants to enter
the joint and will accelerate wear.
( 3) - Lack of grease boot will allow contaminants to enter
the joint and will accelerate wear.
( 4) - Torn grease boot will allow contaminants to enter the
joint and will accelerate wear.
( 5) - If manufacturer's procedures for inspection exist, use
those procedures; otherwise, use an approved inspection
method such as the dry park check.
CAUTION: DO NOT use pliers or pry bar to check ball and
socket movement. Use only moderate hand pressure.
( 6) - Excessive looseness is defined as being significant
enough to affect vehicle handling or structural
integrity.
( 7) - Check for damaged taper hole.
( 8) - Check for damaged stud.









\









\









\









\









\









\









\


SHOCK ABSORBERS, STRUT CARTRIDGES AND STRUT ASSEMBLIES
You are not required to replace shocks or struts in axle
sets. However, when replacing a shock or strut due to the conditions
that follow, you may suggest replacement of the other shock or strut
on the same axle for improved performance and preventive maintenance.
* Part is close to the end of its useful life
* To extend tire life
* To balance ride and handling
* To improve stopping distance
When replacing steering and/or suspension components which
may affect an alignment angle, you are required to check and adjust
alignment as needed. Refer to the OEM specifications.
Under no circumstances should a technician bend struts or
strut housings.
A vehicle's load-carrying and handling abilities are limited
by its suspension, tires, brakes, and driveline. Installing coil over
shocks or any other load assist device does not increase the vehicle's
load capacity. See the vehicle owner's manual for more details.
NOTE: If vehicle is equipped with original equipment coil over
shocks, apply the conditions for coil springs from the
SPRINGS - COIL, LEAF AND TORSION BAR section of the
STEERING AND SUSPENSION guidelines. If the vehicle is
equipped with add-on coil over shocks, you may suggest
replacing the shocks with standard shocks for any spring-
related condition.
SHOCK ABSORBER, STRUT CARTRIDGE AND STRUT ASSEMBLY INSPECTION









\









\









\









\









\









\









\

Condition Code Procedure
Attaching hardware bent . B ... Require repair or replacement
of bent part, if available;
otherwise, replace shock or
strut.
Attaching hardware
broken ................. A ... Require replacement of broken
part, if available; otherwise,
replace shock or strut.
Attaching hardware
corroded, affecting
structural integrity ... A . Require replacement of corroded
part, if available; otherwise,
replace shock or strut.
Attaching hardware
incorrect .............. A .......... Require replacement of
incorrect part, if available;
otherwise, replace shock or
strut.
Attaching hardware
loose .................. A ... Require repair or replacement
of loose part, if available;
otherwise, replace shock or
strut.
Attaching hardware
missing ................ C .. Require replacement of missing
part, if available; otherwise,
replace shock or strut.
Attaching hardware
threads damaged ........ A ... Require repair or replacement
of part with damaged threads,
if available; otherwise,
replace shock or strut.
Attaching hardware
threads stripped
(threads missing) ...... A ..... Require replacement of part
with stripped threads, if
available; otherwise, replace
shock or strut.
Binding ................. A ............ Require replacement.
Body dented ............. A .......... (1) Further inspection
required.
Body punctured .......... A ............ Require replacement.
Brake hose bracket
bent ................... B .. Require repair or replacement.
Brake hose bracket
missing ................ C ............ Require replacement.
Brake hose bracket
threads damaged ........ A .. Require repair or replacement.
Brake hose bracket
threads stripped
(threads missing) ...... C ............ Require replacement.
Compression bumper
missing ................ C .......... Require replacement of
compression bumper.
Compression bumper
split .................. 1 .......... Suggest replacement of
compression bumper.
Damping (none) .......... A ............ Require replacement.
Dust boot (bellows)
split .................. 2 ......... ( 2) Suggest replacement
of boot.

Removal
Raise and support vehicle. Remove wheel assembly. Remove hub
cap. Remove snap ring and shim. Remove drive flange. Remove brake
caliper and suspend with wire. On vehicles with ABS, remove ABS speed
sensor. On all models, remove lock washer. Remove lock nut using
Socket (MB990954). See Fig. 2. Remove front rotor and hub assembly.
Installation
To install, reverse removal procedure. Adjust wheel bearing
preload and check drive shaft endplay. See ADJUSTMENTS.
Fig. 2: Exploded View Of Hub Assembly (Montero Sport Shown, Montero
Similar)
Courtesy of Mitsubishi Motor Sales of America.
STEERING KNUCKLE
Removal
1) Raise and support vehicle. Remove wheel assembly. Remove
brake caliper. Remove axle hub assembly. See AXLE HUB ASSEMBLY under
REMOVAL & INSTALLATION . Remove brake dust cover from steering knuckle.
If equipped with ABS, remove ABS speed sensor.
2) On all models, disconnect tie rod end from steering
knuckle. Mark torsion bar adjusting nut for installation reference.
Loosen torsion bar anchor arm assembly adjusting nut. Loosen, but DO
NOT remove, ball joint-to-steering knuckle nuts.
3) Using Steering Linkage Puller (MB991406), separate ball
joints from steering knuckle. Detach upper and lower ball joints from
steering knuckle. Remove steering knuckle from axle shaft. Remove oil

FINAL ANCHOR ARM BOLT PROTRUSION








\









\









\









\









\









\









\







Application/ Right Bolt Left Bolt
Model In. (mm) In. (mm\
)
Montero ................... 3.15 (80.0) .............. 3.15 (80.0\
)









\









\









\









\









\









\









\







4) To complete installation, reverse removal procedure.
Tighten bolts to specification. See TORQUE SPECIFICATIONS. Check
riding height and front wheel alignment. See WHEEL ALIGNMENT
SPECIFICATIONS & PROCEDURES article in WHEEL ALIGNMENT section.
UPPER BALL JOINT
Removal
1) Raise and support vehicle. Remove wheel assembly. Mark
torsion bar adjusting nut for reassembly reference. Release torsion
bar tension. Loosen, but DO NOT remove, upper ball joint-to-steering
knuckle nut.
2) Using Steering Linkage Puller (MB991406), separate ball
joint from steering knuckle. Remove ball joint nut from steering
knuckle. Remove ball joint-to-upper control arm bolts. Remove ball
joint.
Installation
Lubricate ball joint. To complete installation, reverse
removal procedure. Tighten bolts to specification. See
TORQUE SPECIFICATIONS .
SHOCK ABSORBER & UPPER CONTROL ARM
Removal
1) Disconnect actuator on vehicles with Variable Shock
Absorbers. On all models, raise and support vehicle. Support lower
control arm using jackstand. Remove front wheels. Remove lower shock
absorber bolt. Remove nut from top of shock absorber and remove shock
assembly from vehicle.
2) Remove the bump stop from the bump stop bracket. Mark
anchor arm bolt for reassembly reference. Loosen anchor arm bolt to
release torsion bar tension. Disconnect and plug brake hose at frame
mount bracket.
3) Remove cotter pin from upper ball joint stud. Loosen, but
DO NOT remove, ball joint stud nut. Using Steering Linkage Puller
(MB991406), loosen ball joint from steering knuckle. Remove brake hose\
clip and rebound stopper. Remove rebound stopper and brake hose
support from control arm.
4) Remove ABS sensor bracket (if equipped) and rebound
stoppers. Remove upper control arm mounting bolts and shim(s). Note
direction of bolt installation and locations of camber adjustment
shims. Remove control arm. Remove upper ball joint from control arm.
Inspection
Inspect control arm for cracks and deformation. Check ball
joints. See BALL JOINT CHECKING under ADJUSTMENTS & INSPECTION.
Inspect ball joint dust cover for damage, and replace cover as
necessary.
Installation
1) To install, reverse removal procedure. Install control arm
bolts from outside of frame, with nuts against control arm. Install
the upper control with the marking "OUT" on shaft facing outside of
vehicle.