1998 MITSUBISHI LANCER EVOLUTION IV engine

MPI – Troubleshooting13-13
Code No. 25 Barometric pressure sensor systemProbable cause
Range of Check
Ignition switch: ON
Excluding 60 seconds after the ignition switch is turned to ON or immediately
after the engine starts.
Set conditions
Sensor output voltage is 4.5 V or more (corresponding to a barometric pressure
of 114 kPa {855 mmHg} or more) for 4 seconds.
or
Sensor output voltage is 0.2 V or less (corresponding to a barometric pressure
of 53 kPa {40 mmHg} or less) for 4 seconds.Malfunction of the barometric pressure sensor
Improper connector contact, open circuit or
short-circuited harness wire of the barometric pressure
sensor circuit
Malfunction of the engine-ECU
OK
Replace the air flow sensor.
Measure at the air flow sensor con-
nector A-25.
Connect the connector. (Use
the test harness: MB991709)
Voltage between 2 and earth
(Ignition switch: ON)
OK:3.7–4.3 V (Altitude: 0 m)
3.2–3.8 V
(Altitude: 1,200 m)NGMeasure at the air flow sensor con-
nector A-25.
Disconnect the connector, and
measure at the harness side.
Voltage between 1 and earth
(Ignition switch: ON)
OK:4.8–5.2 V
Continuity between 5 and earth
OK:ContinuityNGCheck the following connector:
B-62NG
Repair
OK
Check trouble symptom.
NG
Check the harness wire between
the engine-ECU and the baromet-
ric pressure sensor connector.NG
Repair
OK
Replace the engine-ECU.
OK
Check the following connector:
A-25NG
Repair
OK
Check trouble symptom.Check the harness wire between
the engine-ECU and the baromet-
ric pressure sensor connector.NG
Repair
OK
Measure at the engine-ECU con-
nector B-62.
Connect the connector.
Voltage between 85 and earth
(Ignition switch: ON)
OK:3.7–4.3 V (Altitude: 0 m)
3.2–3.8 V
(Altitude: 1,200 m)NGCheck the harness wire between
the engine-ECU and the baromet-
ric pressure sensor connector, and
repair if necessary.
Check the following connec-
tors:
A-25, B-62
OK
Check trouble symptom.
NG
Replace the engine-ECU.NG
Repair OKNG

MPI – Troubleshooting13-14
Code No.31 Detonation sensor systemProbable cause
Range of Check
Ignition switch: ON
Excluding 60 seconds after the ignition switch is turned to ON or immediately
after the engine starts.
Engine speed is approx. 5,000 r/min or more
Set conditions
The change in the detonation sensor output voltage (detonation sensor peak voltage
at each 1/2 revolution of the crankshaft) is less than 0.06 V for 200 times in succession.Malfunction of the detonation sensor
Improper connector contact, open circuit or
short-circuited harness wire of the detonation sensor
circuit
Malfunction of the engine-ECU
Measure at the detonation sensor con-
nector A-96.
Disconnect the connector and
measure at the harness side.
Continuity between 2 and earth
OK:ContinuityOKCheck the following connector:
B-62NG
Repair
OK
Check trouble symptom.
NG
Check the harness wire between the
engine-ECU and the detonation sensor
connector.OKReplace the detonation sensor.
Check trouble symptom.
NG
Replace the engine-ECU.
NG
Repair
NG
Check the harness wire between the
detonation sensor and earth, and repair
if necessary.
Code No. 41 Injector systemProbable cause
Range of Check
Engine speed is approx. 50–1,000 r/min
The throttle position sensor output voltage is 1.15 V or less.
Set conditions
Surge voltage of injector coil is not detected for 4 seconds.Malfunction of the injector
Improper connector contact, open circuit or
short-circuited harness wire of the injector circuit
Malfunction of the engine-ECU
NG
Check the harness wire between the
resistor and the injector connector, and
repair if necessary.
OK
Check trouble symptom.
OK
Check the injector control circuit.
OK
Measure at the injector connectors
A-53, A-54, A-55, A-56.
Disconnect the connector, and
measure at the harness side.
Voltage between 1 and earth
(Ignition switch: ON)
OK:System voltageNGCheck the following connector:
A-125NG
Repair
Check the injector. (Refer to P.13-34.)
Check the resistor. (Refer to P.13-34.)NG
Replace
OK
Measure at the resistor connector
A-125.
Disconnect the connector, and
measure at the harness side.
Voltage between 3 and earth
(Ignition switch: ON)
OK:System voltageNGCheck the harness wire between the
control relay and the resistor connec-
tor, and repair if necessary.

MPI – Troubleshooting13-15
Code No. 44 Ignition coil and power transistor unit systemProbable cause
Range of Check
Engine speed is approx. 50 – 4,000 r/min.
Engine is not being cranked.
Set conditions
Abnormal engine speed is detected due to misfiring by crank angle sensor. (One
of two coils fails.)Malfunction of the ignition coil
Improper connector contact, open circuit or
short-circuited harness wire of the ignition primary
circuit
Malfunction of the engine-ECU.
NG
Check the harness wire between the ignition coil and ignition switch
connector, and repair if necessary.
2. NG
OK
Replace the engine-ECU.
3. NG
NG
Check the following items.
Check the spark plugs and spark plug cables.
Check the compression pressure.
OK
Check trouble symptom.
OK
Check the following
connectors:
A-110, A-111NG
Repair
NG
Check the harness wire
between the engine-ECU
and ignition coil connec-
tor.NG
Repair
OK
Check trouble symptom.
Check the following
connector:
B-59NG
Repair
OK
Check trouble symptom.
OK
Measure at the ignition coil connectors A-110, A-111.
Disconnect the connector, and measure at the harness.
1. Voltage between 1 and earth (Ignition switch: ON)
OK:System voltage
2. Voltage between 3 and earth (Engine: Cranking)
OK:0.5 – 4.0 V
3. Continuity between 2 and earth
OK:Continuity1. NGCheck the following
connectors:
B-65, B-76NG
Repair
Check the ignition coil. (Refer to Group 16 – Ignition System.)NG
Replace
Check the harness wire between the ignition coil connector and
earth, and repair if necessary.

MPI – Troubleshooting13-16
Code No. 64 Alternator FR Terminal SystemProbable cause
Range of Check
Engine speed is approximately 50 r/min or more.
Set conditions
Input voltage at the alternator FR terminal is 4.5 V or more for 20 seconds.Open circuit in alternator FR terminal circuit
Malfunction of the engine-ECU.
OK
Replace the alternator.
NG
Check the harness wire between
the engine-ECU and alternator
connector.NG
Repair
OK
Check trouble symptom.
Measure at the alternator connec-
tor
Connect the connector.
(Use test harness MB991519.)
Voltage between 4 (blue clip)
and earth
(Engine: Idling)
(Radiator fan: Stopped)
(Headlamp: OFF → ON)
(Brake lamp: OFF → ON)
(Rear defogger switch: OFF
→ ON)
OK:Voltage drops by 0.2 to
3.5 V.NGMeasure at the alternator connec-
tor A-05.
Disconnect the connector, and
measure at the harness side.
Voltage between 4 and earth
(Ignition switch: ON)
OK:4.8 – 5.2 VNGCheck the following connec-
tors:
B-60, A-88NG
Repair
OK
Check trouble symptom.
NG
Check the harness wire between
the engine-ECU and alternator
connector.NG
Repair
OK
Replace the engine-ECU.
OK
Check the following connector:
A-05NG
Repair
OK
Replace the engine-ECU.

MPI – Troubleshooting
Vehicle
speedInitial accel-
erator pedal
depression
NormalHesitation
Sag
Time
(Figure 1)(Figure 2)
Normal
Initial accel-
erator pedal
depression
IdlingStumble
TimeVehicle
speed
13-17
4. PROBLEM SYMPTOMS TABLE
ItemsSymptom
StartingWon’t startThe starter is used to crank the engine, but there is no combustion within the
cylinders, and the engine won’t start.
Fires up and diesThere is combustion within the cylinders, but then the engine soon stalls.
Hard startingEngine starts after cranking a while.
Idling
stabilityRough idle
HuntingEngine speed doesn’t remain constant and changes at idle.
Usually, a judgement can be based upon the movement of the tachometer
pointer, and the vibration transmitted to the steering wheel, shift lever, body, etc.
This is called rough idle or hunting.
Incorrect idle speedThe engine doesn’t idle at the usual correct speed.
Engine stall
(Die out)The engine stalls when the accelerator pedal is released, regardless of whether
the vehicles is moving or not.
Engine stall
(Pass out)The engine stalls when the accelerator pedal is depressed or while it is being
used.
DrivingHesitation, Sag“Hesitation” is the delay in response of the vehicle speed (engine speed) that
occurs when the accelerator is depressed in order to accelerate from the speed
at which the vehicle is now traveling, or a temporary drop in vehicle speed
(engine speed) during such acceleration. Serious hesitation is called “sag”.
(Refer to Figure 1.)
Poor accelerationPoor acceleration is inability to obtain an acceleration corresponding to the
degree of throttle opening, even though acceleration is smooth, or the inability
to reach maximum speed.
StumbleEngine speed increase is delayed when the accelerator pedal is initially
depressed for acceleration. (Refer to Figure 2.)
ShockThe feeling of a comparatively large impact or vibration when the engine is
accelerated or decelerated.
SurgeThis is repeated forward or rearward surging during constant speed travel or
during variable speed travel.
KnockingA sharp sound like a hammer striking the cylinder walls during driving and which
adversely affects driving.
StoppingRun on
(“Dieseling”)The condition in which the engine continues to run after the ignition switch is
turned to OFF. Also called “Dieseling”.

MPI – Troubleshooting13-18
5. SERVICE DATA LIST

Item
No.Inspection
itemInspection contentsNormal condition
11Oxygen
sensorEngine: After having been warmed
up
Air/fuel mixture is made leaner when
When at 4,000 r/min, engine is
suddenly decelerated200 mV or less
Air/fuel mixture is made leaner when
decelerating, and is made richer
when racing.
When engine is suddenly
raced600 – 1,000 mV
Engine: After having been warmed
up
The ox
ygen sensor signal is used to
Engine is idling400 mV or less
(Chan
ges)The oxygen sensor signal is used to
check the air/fuel mixture ratio, and
control condition is also checked by
the ECU.2,500 r/min
(Changes)
600 – 1,000 mV
12Air flow
sensor*
Engine coolant temperature:
8095C
Engine is idling17 – 43 Hz
sensor*80 – 95C
Lamps, electric cooling fan and
all accessories: OFF
2,500 r/min46 – 86 Hz
all accessories: OFF
Transmission: NeutralEngine is racedFrequency increases
in response to racing
13Intake air
temperature
sensor
Ignition switch: ON or with engine
runningWhen intake air temperature
is –20C–20C
sensorWhen intake air temperature
is 0C0C
When intake air temperature
is 20C20C
When intake air temperature
is 40C40C
When intake air temperature
is 80C80C
14Throttle
position
Ignition switch: ONSet to idle position300 – 1,000 mV
position
sensor
Gradually openIncreases in proportion
to throttle opening
angle
Open fully4,500 – 5,500 mV
16Power
supply
voltageIgnition switch: ONSystem voltage
18Cranking
signal Ignition switch: ONEngine: StoppedOFF
g
(ignition
switch-ST)Engine: CrankingON
NOTE
*: When the car is new (distance it travelled is less than 500 km), output frequency of the air flow sensor may
become about 10% higher.

MPI – Troubleshooting13-19
Item
No.Inspection
itemInspection contentsNormal condition
21Engine
coolant
temperature
Ignition switch: ON or with engine
runningWhen engine coolant temper-
ature is –20C–20C
temperature
sensorWhen engine coolant temper-
ature is 0C0C
When engine coolant temper-
ature is 20C20C
When engine coolant temper-
ature is 40C40C
When engine coolant temper-
ature is 80C80C
22Crank angle
sensorEngine: Idling
Idle position switch: ONWhen engine coolant temper-
ature is –20C1,300 – 1,500 rpm
When engine coolant temper-
ature is 0C1,300 – 1,500 rpm
When engine coolant temper-
ature is 20C1,300 – 1,500 rpm
When engine coolant temper-
ature is 40C1,150 – 1,350 rpm
When engine coolant temper-
ature is 80C750 – 950 rpm
25Barometric
pressure
Ignition switch: ONAt altitude of 0 m101 kPa
pressure
sensor
At altitude of 600 m95 kPa
At altitude of 1,200 m88 kPa
At altitude of 1,800 m81 kPa
26Idle position
switchIgnition switch: ON
(Check by operating accelerator
dl tdl )
Throttle valve: Set to idle
positionON
pedal repeatedly.)Throttle valve: Slightly openOFF*1
27Power
steering fluidEngine: IdlingSteering wheel stationaryOFF
tg
pressure
switchSteering wheel turningON
28A/C switchEngine: Idling
(when A/C switch is ON A/C
A/C switch: OFFOFF
(when A/C switch is ON, A/C
compressor should be operating.)A/C switch: ONON

MPI – Troubleshooting13-20
Item
No.Normal condition Inspection contents Inspection
item
41Injector
drive time*2Engine: CrankingWhen engine coolant temper-
ature is 0C (injection is
carried out for all cylinders
simultaneously)27 – 41 ms
When engine coolant temper-
ature is 20C14 – 22 ms
When engine coolant temper-
ature is 80C3.9 – 5.9 ms
Injector
drive time*3Engine coolant temperature:
8095C
Engine is idling1.2 – 2.4 ms
drive time*380 – 95C
Lamps, electric cooling fan and
all accessories: OFF
2,500 r/min1.0 – 2.2 ms
all accessories: OFF
Transmission: NeutralWhen engine is suddenly
racedIncreases
44Ignition
advanceEngine: After having been
warmed up
Timing lamp is set (The timing
Engine is idling3 – 13BTDC
Timing lamp is set. (The timing
lamp is set in order to check
actual ignition timing.)2,500 r/min24 – 44BTDC
45ISC
(stepper)
motor
Engine coolant temperature:
80 – 90C
Lamps electric coolingfan and
A/C switch: OFF2 – 25 steps
motor
position *4Lamps, electric cooling fan and
all accessories: OFF
Transmission: Neutral
Idle position switch: ON
Engine: Idling
A/C switch: OFF → ONIncreases by 10 – 70
steps
Engine: Idling
(When A/C switch is ON, A/C
compressor should be operat-
ing.)A/C switch: OFFIncreases by 5 – 50
steps
49A/C relayEngine: After having been warmed
up/Engine is idlingA/C switch: OFFOFF (Compressor
clutch is not operating)
A/C switch: ONON (Compressor
clutch is operating)
NOTE
*1: The idle position switch normally turns off when the voltage of the throttle position sensor is 50 – 100 mV
higher than the voltage at the idle position. If the idle position switch turns back on after the throttle valve
is opened, the idle position switch and the throttle position sensor need to be adjusted.
*2: The injector drive time represents the time when the cranking speed is at 250 r/min or below when the power
supply voltage is 11 V.
*3: In a new vehicle [driven approximately 500 km or less], the injector drive time is sometimes 10% longer than
the standard time.
*4: In a new vehicle [driven approximately 500 km or less], the step of the stepper motor is sometimes 30 steps
greater than the standard value.