1998 MITSUBISHI LANCER EVOLUTION IV engine

ENGINE – T iming Belt 11-31
(17)Loosen the retaining bolt of the tensioner pulley.
Caution
Loosening the retaining bolt can cause the intake
and exhaust camshafts to turn, resulting in slackened
timing belt. Use care that the timing belt does not
come off the sprockets at this time.
(18)Pull up the slack of the timing belt by turning the tensioner in illustrated direction using the special tool and a torque
wrench (0 – 5 Nm {0 – 0.5 kgf
m}).
(19)From this position, turn back the tensioner until the torque wrench reading becomes 3.5 Nm {0.36 kgf
m}, then
secure it by tightening the retaining bolt.
(20)Remove the special tool attached in step (16).
(21)Rotate the crankshaft clockwise 2 turns. Then, leave it intact 15 minutes.
(22)Check to see that the wire inserted when installing the
auto-tensioner can be pulled out lightly. If it can be pulled
out lightly, the timing belt is being tensioned properly.
If so, remove the wire. In addition, check that the rod
protrusion from the auto-tensioner meets the standard
value, which is also an indication of properly tensioned
timing belt.
Standard value: 3.8 – 4.5 mm
(23)If the wire cannot be removed with a light force, repeat steps (16) through (21) until the proper belt tensioner
is obtained.MD998767

ENGINE – Engine Assembly 11- 32
ENGINE ASSEMBLY
REMOVAL AND INSTALLATION
Pre-removal Operation
(1) Fuel Discharge Prevention
(2) Hood Removal
(3) Strut Tower Bar Removal
(4) Air Hose C Removal
(Refer to GROUP 15 – Intercooler.)
(5) Radiator Assembly Removal (Refer to GROUP 14.)
(6) Under Cover Removal
(7) Front Exhaust Pipe Removal (Refer to GROUP 15.)Post-installation Operation
(1) Front Exhaust Pipe Installation
(Refer to GROUP 15.)
(2) Under Cover Installation
(3) Radiator Assembly Installation (Refer to GROUP 14.)
(4) Accelerator Cable Adjustment
(5) Air Hose C Installation (Refer to GROUP 15 – Intercooler.)
(6) Strut Tower Bar Installation
(7) Hood Installation
O-ring Delivery pipe
1
2
3
4
5
6
7 8
9
10
11
18 12
Engine oil
5 {0.5}
Unit: Nm {kgf

m}
10 – 12
{1.0 – 1.2}
17 1614 13
10
– 12
{1.0 – 1.2}
15
3 {0.3}
17
8
Removal steps1. Center cover
2. Accelerator cable
3. Brake booster vacuum hose connection
4. Vacuum hose connection
5. Throttle position sensor connector
6. Idle speed control motor connector
7. Heater hose connection
8. Ignition coil connector
9. Crank angle sensor connector
10. Oxygen sensor connector 11. Injector connector
12. Cam position sensor connector
13. Coolant temperature sensor con-
nector
14. Coolant temperature gauge unit connector
15. Vacuum pipe/hose assembly
16. Control harness
 C 17. High-pressure fuel hose connection
18. Fuel return hose connection

ENGINE – Engine Assembly11- 33
25
27 2819
20 21
22 23
24
26
Unit: Nm {kgf
m}
98 {10.0}*
29
57 {5.8}
22
12 {1.2} 39 {4.0}
9 {0.9}
19. Solenoid valve connector
20. Vacuum tank/solenoid valve/vacuum hose assembly
21. Oil pressure switch connector
22. Alternator connector  Drive belt tension inspection
(Refer to P.11-4.)
 A 23. Drive belt
 B 24. A/C compressor
 C 25. Power steering oil pump
 Transmission assembly 26. A/C relay box
27. A/C receiver bracket mounting bolt
28. Oil pressure hose mounting bolt
 C B 29. Engine mount bracket
 E A 30. Engine assembly
Caution
Mounting locations marked by * should be
provisionally tightened, and then fully tightened after
placing the vehicle horizontally and loading the full
weight of the engine on the vehicle body.

ENGINE – Engine Assembly 11- 34
REMOVAL SERVICE POINTS
 A DRIVE BELT REMOVAL
(1) Align the hole in the auto tensioner bracket with that in the arm and insert a screwdriver into the holes.
(2) Remove the drive belt.
 B POWER STEERING OIL PUMP REMOVAL
Remove the power steering oil pump from the bracket with
the hose attached.
NOTE
Place the removed power steering oil pump in a place where
it will not be a hindrance when removing and installing the
engine assembly, and tie it with a cord.
 C A/C COMPRESSOR REMOVAL
Disconnect the A/C compressor connector and remove the
compressor from the compressor bracket with the hose still
attached.
NOTE
Place the removed A/C compressor where it will not be a
hindrance when removing and installing the engine assembly,
and tie it with a cord.
 D ENGINE MOUNT BRACKET REMOVAL
(1) Support the engine with a garage jack.
(2) Remove the special tools which was attached when the transmission assembly was removed.
(3) Hold the engine assembly with a chain block or similar tool.
(4) Place a garage jack against the engine oil pan with a piece of wood in between, jack up the engine so that
the weight of the engine is no longer being applied to
the engine mount bracket, and then remove the engine
mount bracket.
Phillips
screwdriver
Hole in arm
Auto tensioner
Hole in bracket
MZ203826 or MZ203827
MB991453

ENGINE – Engine Assembly11-3 5
E ENGINE ASSEMBLY REMOVAL
After checking that all cables, hoses and harness connectors,
etc., are disconnected from the engine, lift the chain block
slowly to remove the engine assembly upward from the engine
compartment.
INSTALLATION SERVICE POINTS
 A ENGINE ASSEMBLY INSTALLATION
Install the engine assembly, checking that the cables, hoses,
and harness connectors are not clamped.
 B ENGINE MOUNT BRACKET INSTALLATION
(1) Place a garage jack against the engine oil pan with a piece of wood in between, and install the engine mount
bracket while adjusting the position of the engine.
(2) Support the engine with the garage jack.
(3) Remove the chain block and support the engine assembly
with the special tools.
 C HIGH-PRESSURE FUEL HOSE INSTALLATION
(1) Apply a small amount of new engine oil to the O-ring, then fit the O-ring in the delivery pipe.
Caution
Do not let any engine oil get into the delivery pipe.
(2) Check that the high pressure hose turns smoothly. If the hose does not turn smoothly, the O-ring is probably
being clamped. Disconnect the high-pressure fuel hose
and check the O-ring for damage. After this, re-install
the hose to the delivery pipe and check that the hose
turns smoothly.
(3) Tighten the mounting bolt to the specification.
MZ203826 or MZ203827
MB991453

LUBRICANTS 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ENGINE OIL COOLER 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12-1
ENGINE
LUBRICATION
CONTENTS

ENGINE LUBRICATION – Lubricants / Engine Oil Cooler12-2
TSB Revision
LUBRICANTS
ItemsCapacity dm3 {
}
Engine oilQuantity in oil filter0.3 {0.3}
Quantity in oil cooler0.16 {0.16}
Total quantity5.1 {5.1}
BrandDIA QUEEN MOTOR OIL (Grade SG or higher); or engine oil in
a can marked with ILSAC certification.
ENGINE OIL COOLER
REMOVAL AND INSTALLATION
Pre-removal and Post-installation Operation
(1) Engine Oil Removal and Refilling
(2) Front Bumper Removal and Installation
(Refer to GROUP 51.)
3
Unit: Nm {kgfm}
12 {1.2}
39 – 44
{4.0 – 4.5} 29 – 34
{3.0 – 3.5}
2 1
39 – 44
{4.0 – 4.5} 12 {1.2}
12 {1.2}
Removal steps
1. Engine oil cooler

A2. Feed hose assembly

A3. Return hose assembly
INSTALLATION SERVICE POINT

AFEED HOSE ASSEMBLY / RETURN HOSE
ASSEMBLY INSTALLATION
Fit the hose joint positioning tab into the hole in oil cooler
to secure the hose assembly in position.

13-1
FUEL
CONTENTS
MULTIPOINT INJECTION (MPI) 2. . . . . . .
GENERAL INFORMATION 2. . . . . . . . . . . . . . . .
SERVICE SPECIFICATIONS 3. . . . . . . . . . . . . .
SEALANT 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SPECIAL TOOLS 4. . . . . . . . . . . . . . . . . . . . . . . .
TROUBLESHOOTING 6. . . . . . . . . . . . . . . . . . . .
ON-VEHICLE SERVICE 30. . . . . . . . . . . . . . . .
1. Idle Position Switch and Throttle Position
Sensor (TPS) Adjustment 30. . . . . . . . . . . . .
2. Fixed SAS Adjustment 30. . . . . . . . . . . . . . . .
3. Basic Idle Speed Adjustment 30. . . . . . . . . . 4. Fuel Pressure Measurement 30. . . . . . . . . . .
5. MPI System Components Layout 31. . . . . .
6. Intake Air Temperature Sensor Check 32. .
7. Engine Coolant Temperature
Sensor Check 32. . . . . . . . . . . . . . . . . . . . . . . .
8. Oxygen Sensor Check 32. . . . . . . . . . . . . . . .
9. Injector Check 34. . . . . . . . . . . . . . . . . . . . . . .
10. Resistor Check 34. . . . . . . . . . . . . . . . . . . . . . .
11. Fuel Pump Relay No.2 Check 35. . . . . . . . .
12. Fuel Pump Resistor Check 35. . . . . . . . . . . . INJECTOR 36. . . . . . . . . . . . . . . . . . . . . . . . . . . .
THROTTLE BODY 37. . . . . . . . . . . . . . . . . . . . .