1998 HONDA INTEGRA light

3. Remove the front and rear ceiling lights, then djs
connect the connectofs.


: Screw, nut locations
AA
CONNECTOR
FRONTLIGHTCEILING
REAR CEILINGLIGHT
HOOK
A
N
LENS
CONNECTOR
Remove the grab handles (Iront and
senger's) and grab holF caps {dl|ver'sr.
GRAB HANDLE
GRAE HOLE CAPS
Screw locations.
ciEI
6t
J-.
20-101

Bumpers
Front Bumper Replacement (cont'dl
>: Solt scaew location3A>:5
FF
FRONT TURNSIGNAL LIGHTHOLDER
l,r/'
SIDE CLIPS
SIDE PLATE
FRONT BUMPER
Mffi
l//'
R<"
,-wf
"-@
SIGNAL LIGHT
FRONT SPOILER{Type-Rl
Installation is the reverse of the removal procedure.
20-142

\
Bumpers
Rear Bumper Replacement
JCAUTION: Wear gloves to remove and install the rear
bumper.
NOTE:
. An assistant is helpful when removing the rear
bumper.
. Take care not to scratch the rear bumper and body.
Hatchback:
1. Remove the nuts, screws and clips, then remove the
rear bumper.
a: Nul locrtion3, a >: Scrow locations,2
n 6x1.0mm AffiJls.a N.- H
k i tr.o rgt.-, A. - 7.2 lbl.ftl t\+-z
\.!
>: Clip location3,2
REAR BUMPERCONNECTORDisconnect,
nQn
wl\lvxvn
\-:
NOTE: lf necessary, disassemble the rear bumper.
>: Clip locatiom, 9 >: Scr.w locationr. 4
l_4h- (E('-
\"
t s]@!-
BEAR BUMPERUPPER BEAM
LICENSE PLATELIGHT
REAR BUMPER
Remove the absorber, bumper
rear oumper Deam.
V: Boll locations,4
beam gusset and
12 x 1.25 mm64 N m 16.5 kgf m,47 rbf.rtl .)
ACCESS CAP
ABSOREER
BUMPER BEAMGUSSET
lnstallation is the reverse of the removal Drocedure.
NOTE: Make sure the license plate light connector
is connected, and the grommet is installed properly.
{cont'd)
,@
H
,lI
REAR BUMPER
20-143

Bumpers
REAR BUMPER
Rear Bumper Replacement (cont'd)
Sedan:
1. Remove the screw lrom each side.
Screw
A
,z::\+,1./
REAR BUMPER
2. Open the trunk lid, then remove the rear trim panel
(see page 20-97).
3. Disconnect the license plate light connector and
grommet from the rear trunk area. Remove the clips
and bolts, then remove the rear bumper.
V: Clip locations, 5 A: Bolt locations, 2
A
/.r-El^ El
=EE Atn) ('r\,
,/
*LICENSE PLATE LIGHTCONNECTOR
20-144
GROMMET
4. lf necessary, remove the license plate light harness,
bracket and lens from the rear bumper (see page
20-1431.
5. Remove the absorber, bumper beam gusset and rearoumper oeam.
V : Eolt locations, 4
12 x 1.25 mm I64 N.m 16.5 kgl.m, j
-::_:_)
fr)

Il
6. Installation is the reverse of the removal procedure.
NOTE;
r Make sure the license plate light connector is
connected, and the grommet is installed properly.
. Make sure the rear bumper engages the side clips
securely.
REAB BUMPER
20-145

NOTE: Before adjusting the hood, loosen each bolt slightly.
1. Adjust the hood hinges right and left, as well as lore and aft, by using the elongated holes.
2. Turn the hood edge cushions, as necessary, to make the hood ,fit flush with the body at front and side edges.
3. Adjust the hood latch to obtain the proper height at the forward edge.
HOOD EDGECUSHION
NOTEi Move the hood latch right or lett until the striker
is centered in the hood latch as shown.HOOD LATCH
HOOO LATCH
7.2lblltl
4. After adjustment, tighten each bolt securely.

Adjustment
NOTE:
. Before adjusting the hatch, loosen each bolt and nut slightly.
. Do not installthe support struts.
1. Adjust the hatch hinges rightand left, aswell asforeand aft. byusing the elongated holes.
2. Turn the hatch edge cushions, as necessary, to make the hatch fit flush with the body at each side.
3. Adjust the hstch fit to the hatch opening by moving the striker.
4. Use shims. as necessary, to make the hatch fit flush with the body at the rear edge.
5. Adiust the hatch side stop so that there is no clearance between it and the body side stop, then tighten the mounting
bolt (Tvpe R).
HATCHEDGE CUSHION
STOP(Typ. R
Modoll
SIDESTOPlTyp. R
Modell
HATCHEDGECUSHION
stoE
STRIKER
HATCHEDGE CUSHION
Type R Model:
SIDE STOP(Hatch side)
SIDE STOP(Body side)
6xl,0mft9.8 N.m 11.0 kg{.m,7.2 tbf.ftl
6x1.0mm9.8 N.m (1.0 kgt m,?.2 tbf.ftl
SIDE STOP(Hatch side)
Adjust forno clearance,
SIDE STOP(Body side)
NOTE: Move the striker right or left until it's centered
in the hatch latch as shown.
STRIKER
HATCH
8 x 1.25 mm
SHIM
8 x 1.25 mm22 N.m 12.2 kgl.m,16 rbt.ft)
HATCH

NOTE: Before adjusting the trunk lid. loosen each bolt slightly.
1. Adjust the trunk lid hinges right and left, as well as fore and att, by using the elongated holes.
2. Turn the trunk lid edge cushions, as necessary. to make the trunk lid fit flush with the body at the rear and side edges.
3. Adjust the lit between the trunk lid and the trunk lid opening by moving the striker.
TNUNK LID EDGECUSHION
TRUNK LIOHINGE
NOTE: Move the striker right or left until it's centered
in the trunk lid latch as shown.6 r 1.0 mm9.8 N m (1.O kgf .m,
7 .2 tbt.ltl
6 x '1.0 mm
STRIKER
STFIKER
4. After adjustment, tighten each bolt securely.
Adjustment
20-153