1997 TOYOTA TACOMA engine

194
ADDING DISTILLED WATER (MAINTE-
NANCE TYPE BATTERY ONLY)
1. Remove the vent plugs.
2. Add distilled water to cells needingfluid.
If the side of your battery is covered,
check the water level by looking down di-
rectly above the cell as illustrated above.
3. Retighten the vent plugs securely
NOTICE
Do not overfill the cells. Excess electrolyte could squirt out of the
battery during heavy charging,causing corrosion or damage.
During recharging, the battery is pro-
ducing hydrogen gas. Therefore, before recharging:
1. Maintenance type batteriesÐRemove the vent plugs.
2. If recharging with the battery installed on the vehicle, be sure to disconnect the ground cable.
3. Be sure the power switch on the re- charger is off when connecting the
charger cables to the battery and
when disconnecting them.
Always charge the battery in an
unconfined area. Do not charge
the battery in a garage or closed
room where there is not sufficient ventilation.
Non-maintenance batteries: Only
do a slow charge (5A or less).
Charging at a quicker rate is dan-
gerous. The battery may explode,
causing personal injuries.
Maintenance type batteries: Be sure to remove the vent plugs be-fore recharging. CAUTION
!
NOTICE
Never recharge the battery while the
engine is running. Also, be sure all
accessories are turned off.
Battery recharging precautions

196If the new fuse immediately blows out, there is a problem with the electrical sys-
tem.
Have your Toyota dealer correct it as
soon as possible.
Never use a fuse with a higher
amperage rating, or any other
object, in place of a fuse. This maycause extensive damage and
possibly a fire. CAUTION
!
If any washer does not work, the wash-
er tank may be empty. Add washer fluid.
You may use plain water as washer fluid.
However, in cold areas where tempera-
tures range below freezing point, use
washer fluid containing antifreeze. This
product is available at your Toyota dealer
and most auto parts stores. Follow the
manufacturer 's directions for how much
to mix with water.
NOTICE
Do not use engine antifreeze or any other substitute because it may
damage your vehicle's paint.
The following illustrations show how to
gain access to the bulbs. When replacing
a bulb, make sure the ignition switch and
light switch are off. Use bulbs with the wattage ratings given in the table.
NOTICE
Only use a bulb or unit of the listed type.
Light Bulbs and
UnitsBulb and Unit No.WType
Headlight unitsH605965/35Ð
Headlight bulbs900360/55D
Parking lights1685B
Front turn signal lights115627A
Rear turn signal lights115627A
Stop and tail lights115727/8A
Back-up lights115627A
License plate lights1943.8B
High mounted stop- light1685B
Adding washer fluid Replacing light bulbs and unitsÐ

Normal cab models Xtra-cab models
Overall length mm (in.) 4440 (174.8) *1
4910 (193.3) *1
4590 (180.7) *2
5055 (199.0) *2
Overall width mm (in.) 1690 (66.5) 1690 (66.5)
Overall height mm (in.) 1570 (61.8) *3,
5
1575 (62.0) *5
1575 (62.0) *4,
5
Wheelbase mm (in.) 2625 (103.3) 3095 (121.9)
Front tread mm (in.) 1395 (54.9) *3
1425 (56.1)
1425 (56.1) *4
Rear tread mm (in.) 1415 (55.7) *3
1440 (56.7)
1440 (56.7) *4
Cargo weight rating kg (lb.) 500 (1100) *6
500 (1100)*6
430 (950) *7
430 (950)*7
295 (650) *8
*1 : Without rear step bumper
*2 : With rear step bumper
*3 : With P195/75R 14 tires
*4 : With P215/70R 14 tires
*5 : Unladen vehicle
*6 : With 1 or 2 occupants
*7 : With 3 occupants
*8 : With 5 occupants
Part 8 Dimensions and weight
205
SPECIFICATIONS
Dimensions and weight
Engine
Fuel
Service specifications
Tires
Fuses
TWO-WHEEL DRIVE MODELS

206
FOUR-WHEEL DRIVE MODELS
Model:
2RZ-FE, 3RZ-FE and 5VZ-FE
Type: 2RZ-FE and 3RZ-FE engine
4 cylinder in line, 4 cycle, gasoline
5VZ-FE engine 6 cylinder V type, 4 cycle, gasoline
Bore and stroke, mm (in.): 2RZ-FE engine
95.0 x 86.0 (3.74 x 3.39)
3RZ-FE engine
95.0 x 95.0 (3.74 x 3.74)
5VZ-FE engine 93.5 x 82.0 (3.68 x 3.23)
Displacement, cm 3
(cu. in.):
2RZ-FE engine 2438 (148.8)
3RZ-FE engine 2694 (164.3)
5VZ-FE engine
3378 (206.1)
Normal cab models Xtra-cab models
Overall length mm (in.) 4585 (180.5) 5055 (199.0)
Overall width mm (in.) 1690 (66.5) *1
1690 (66.5)
1720 (67.7) *2
1720 (67.7)*2
Overall height mm (in.) 1710 (67.3) *1,3
1700 (66.9)*1,3
1740 (68.5) *2,3
1735 (68.3)*2,3
Wheelbase mm (in.) 2625 (103.3) 3095 (121.9)
Front tread mm (in.) 1395 (54.9) *3
1460 (57.5)*4
1500 (59.1) *5
1500 (59.1)*5
Rear tread mm (in.) 1455 (57.3) *4
1455 (57.3)*4
1495 (58.9) *5
1495 (58.9)*5
Cargo weight rating kg (lb.) 500 (1100) 500 (1100) *6
317 (700) *7
*1 : With P225/75R 15 tires
*2 : With 31 x 10.5R 15 LT tires
*3 : Unladen vehicle
*4 : With steel wheels
*5 : With aluminum wheels
*6 : With 3 occupants
*7 : With 5 occupants
Engine

207
Fuel type:
Unleaded gasoline, Research Octane Number 91 (Octane Rating 87) orhigher
Fuel tank capacity, L (gal., Imp. gal.):
Two-wheel drive models
57 (15.1, 12.5) Four-wheel drive models
68 (18.0, 15.0) ENGINE
Valve clearance (engine cold), mm (in.) 2RZ-FE and 3RZ-FE engines
Intake 0.15 '0.25 (0.006 '0.010)
Exhaust 0.25 '0.35 (0.010 '0.014)
5VZ-FE engine
Intake 0.13 '0.23 (0.006 '0.009)
Exhaust 0.27 '0.37 (0.011 '0.014)
Spark plug type: 2RZ-FE and 3RZ-FE engines NIPPONDENSO K16R-U
NGK BKR5EYA
5VZ-FE engine
NIPPONDENSO K16TR11
NGK BKR5EKB11
Spark plug type: 2RZ-FE and 3RZ-FE engines
0.8 (0.031)
5VZ-FE engine
1.1 (0.043) Drive belt tension measured with Bor-
oughs drive belt tension gauge No.
BT-33-73F (used belt), Ibf: 2RZ-FE and 3RZ-FE engines
Generator belt 115 + 20
Air conditioning
compressor belt 100 + 20
Power steering pump belt 100 -15+20
5VZ-FE engine Generator belt 100 + 20
Air conditioning
compressor belt 100 + 20
Power steering pump belt 100 -15+20
Fuel
Service specifications

208
ENGINE LUBRICATION Oil capacity (drain and refill), L (qt., Imp. qt.):
Two-wheel drive models 2RZ-FE engine
With filter 5.5 (5.8, 4.8)
Without filter 4.8 (5.0, 4.2)
5VZ-FE engine
With filter 5.4 (5.7, 4.8)
Without filter 5.1 (5.4, 4.5)
Four-wheel drive models 3RZ-FE engine
With filter 5.4 (5.7, 4.8)
Without filter 4.7 (5.0, 4.1)
5VZ-FE engine With filter 5.2 (5.5, 4.6)
Without filter 4.9 (5.2, 4.3)
Oil grade:
API SH, Energy-Conserving IIº multi-
grade engine oil or ILSAC multigrade en-
gine oil is recommended. Recommended oil viscosity (SAE):
COOLING SYSTEM
Total capacity, L (qt., Imp. qt.):
Two-wheel drive models With manual transmission
2RZ-FE engine
8.0 (8.5, 7.0)
5VZ-FE engine 9.7 (10.3, 8.5)
With automatic transmission
2RZ-FE engine 7.8 (8.2, 6.9)
5VZ-FE engine 9.5 (10.0, 8.4) Four-wheel drive models With manual transmission
3RZ-FE engine
8.3 (8.8, 7.3)
5VZ-FE engine 10.1 (10.7, 8.9)
With automatic transmission
3RZ-FE engine 8.2 (8.7, 7.2)
5VZ-FE engine 10.0 (10.5, 8.8)
Coolant type: With ethylene-glycol antifreeze (Do not use alcohol type.)
BATTERY Open voltage* at 20 C (68 F):
12.7 V Fully charged 12.3 V Half charged
11.9 V Discharged
*Voltage that is checked 20 minutes after
the key is removed with all the lights
turned off Charging rates: 5 A max.

209
CLUTCH
Pedal freeplay, mm (in.):
5' 15 (0.2 '0.6)
Fluid type: SAE J1703 or FMVSS No. 116 DOT 3
MANUAL TRANSAXLE
Oil capacity, L (qt., Imp. qt.):
2RZ-FE engine 2.6 (2.7, 2.3)
3RZ-FE engine 2.5 (2.6, 2.2)
5VZ-FE engine
Two-wheel drive models 2.6 (2.7, 2.3)
Four-wheel drive models 2.2 (2.3, 1.9)
Oil type:
Multipurpose gear oil API GL-4 or GL-5
Recommended oil viscosity:
SAE 75W-90 AUTOMATIC TRANSMISSION Fluid capacity (drain and refill), L (qt., Imp. qt.):
Two-wheel drive models 2RZ-FE engine
Up to 2.4 (2.5 2.1)
5VZ-FE engine Up to 1.6 (1.7, 1.4)
Four-wheel drive models Up to 2.0 (2.1, 1.8)
Fluid type:
Automatic transmission fluid D-II or DEXRON [
III (DEXRON [
II)
TRANSFER
Oil capacity, L (qt., lmp. qt.): 1.0 (1.1, 0.9)
Oil type: Multipurpose gear oil API GL-4 or
GL-5 Recommended oil viscosity: SAE 75W-90 DIFFERENTIAL
Oil capacity, L (qt., lmp. qt.):
Two-wheel drive models
2RZ-FE engine 1.35 (1.4, 1.2)
5VZ-FE engine 2.55 (2.7, 2.2)
Four-wheel drive models Front A.D.D. 1.15 (1.2, 1.0)
Except A.D.D. 1.1 (1.2, 1.0)
Rear Short wheel base
With rear differential lock system 2.65 (2.8, 2.3)
Without rear differential lock system 2.55 (2.7, 2.2)
Extra long wheel base
With rear differential lock system 2.95 (3.1, 2.6)
Without rear differential lock system 2.05 (2.2, 1.8)
Oil type: Hypoid gear oil API GL-5

210
Recommended oil viscosity:
Front A.D.D.
SAE 75W-90
Except A.D.D. Above -18 C (0 F)
SAE 90
Below -18 C (0 F)
SAE 80W or 80W-90
Rear Above -18 C (0 F)
SAE 90
Below -18 C (0 F)
SAE 80W or 80W-90 CHASSIS LUBRICATION Wheel bearings:
Lithium base wheel bearing grease, NLGI No. 2
Front drive shaft thrust bushings:
Synthetic oil and lithium soap basechassis grease, NLGI No. 1
Propeller shafts:
SpidersLithium base chassis grease, NLGI No. 2
Slide youke and double cardan joint
Molybdenum-disulfide lithiumbase chassis grease, NLGI No. 2
BRAKES Minimum pedal clearance when de- pressed with the pressure of 490 N (50
kgf, 110 lbf) with the engine running, mm(in.): 72 (2.8)
Pedal freeplay, mm (in.):
3' 6 (0.12 '0.24)
Pad wear limit, mm (in.):
1.0 (0.04)
Lining wear limit, mm (in.):
1.0 (0.04)
Parking brake adjustment when pulled with the force of 196 N (20 kgf, 44 lbf):
12'18 clicks
Fluid type:
SAE J1703 or FMVSS No. 116 DOT 3 STEERING Wheel freeplay:
Less than 30 mm (1.2 in.)
Power steering fluid type: Automatic transmission fluid DEXRON [
II or III