1997 TOYOTA SUPRA weight

LU04X-02
P02149
P02186
Mark
ºº
P02294
P02157
- LUBRICATIONOIL PUMP
LU-13
1460 Author
: Date
:
1997 SUPRA (RM502U)
INSPECTION
1. INSPECT RELIEF VALVE
Coat the valve with engine oil and check that it falls smoothly
into the valve hole under its own weight.
If it doesn't, replace the relief valve. If necessary, replace the oil
pump assembly.
2. PLACE DRIVE AND DRIVEN ROTORS INTO OIL PUMP
BODY
(a) Place drive and driven rotors into oil pump body
HINT:
Place the drive and driven rotors into the oil pump body with the
mark facing upward.
3. INSPECT ROTOR TIP CLEARANCE
Using a feeler gauge, measure the clearance between the drive
and driven rotors.
Standard tip clearance:
2JZ-GE: 0.060 - 0.240 mm (0.0024 - 0.0094 in.)
2JZ-GTE: 0.056 - 0.326 mm (0.0022 - 0.0128 in.)
Maximum tip clearance:
2JZ-GE: 0.30 mm (0.0118 in.)
2JZ-GTE: 0.40 mm (0.0157 in.)
If the tip clearance is greater than maximum, replace the rotors
as a set.
4. INSPECT ROTOR BODY CLEARANCE
Using a feeler gauge, measure the clearance between the driv-
en rotor and pump body.
Standard body clearance:
2JZ-GE: 0.100 - 0.175 mm (0.0039 - 0.0069 in.)
2JZ-GTE: 0.080 - 0.135 mm (0.0031 - 0.0053 in.)
Maximum body clearance:
2JZ-GE: 0.20 mm (0.0079 in.)
2JZ-GTE: 0.16 mm (0.0063 in.)
If the body clearance is greater than maximum, replace the ro-
tors as a set. If necessary, replace the oil pump assembly.

AB0158
SSTBattery
R05752
SST
AB0164
RS-16
- SUPPLEMENTAL RESTRAINT SYSTEMSTEERING WHEEL PAD AND SPIRAL CABLE
1955 Author
: Date
:
1997 SUPRA (RM502U)
(c) Confirm functioning of the SST.
SST 09082-00700
(d) Install the SST.
CAUTION:
Place the disc wheel on the level ground.
Connect the SST connector to the steering wheel pad
connector.
SST 09082-00700
NOTICE:
To avoid damaging the SST connector and wire harness,
do not lock the secondary lock of the twin lock. Also, se-
cure some slack for the SST wire harness inside the disc
wheel.
(e) Cover the steering wheel pad with cardboard box or tires.

Covering method using cardboard box:
Cover the steering wheel pad with the cardboard
box and weight the cardboard box down in 4 places
with at least 196 N (20 kg, 44 lb).
Size of cardboard box:
Must exceed the following dimensions:
x=460 mm (18.11 in.)
When dimension of the cardboard box exceeds the di-
ameter of the disc wheel with tire to which the steer-
ing wheel pad is tied -
x=460 mm (18.11 in.) + width of tire
y= 650 mm (25.59 in.)
NOTICE:
If a cardboard box smaller than the specified size is used,
the cardboard box will be broken by the shock from the air-
bag deployment.

R13897Inscribed Mark
R07603
R07591
Compressed Air
R07600
Inscribed
Mark
SR-30
- STEERINGPOWER STEERING VANE PUMP
1914 Author
: Date
:
1997 SUPRA (RM502U)
If it is more than the maximum, replace the plate and/or rotor
with one having the same mark stamped on the cam ring.
Inscribed mark:
1, 2, 3, 4 or None
HINT:
There are 5 vane plate lengths with the following rotor and cam
ring marks:
Rotor and cam
ring markVane plate part
numberVane plate length
mm (in.)
None44345-2601014.999-15.001
(0.59051-0.59059)
144345-2602014.997-14.999
(0.59043-0.59051)
244345-2603014.995-14.997
(0.59035-0.59043)
344345-2604014.993-14.995
(0.59027-0.59035)
444345-2605014.991-14.993
(0.59020-0.59027)
3. INSPECT FLOW CONTROL VALVE
(a) Coat the valve with power steering fluid and check that it
falls smoothly into the valve hole by its own weight.
(b) Check the valve for leakage.
Close one of the holes and apply 392 - 490 kPa (4 - 5 kgf/
cm
2, 57 - 71 psi) of compressed air into the opposite side,
and confirm that air does not come out from the end holes.
If necessary, replace the valve with one having the same letter
as inscribed on the front housing.
Inscribed mark:
A, B, C, D, E or F