1997 TOYOTA SUPRA door lock

I02082I02081
I02080
I02079
I05022
Security Indicator
TRAC OFF Indicator
Low Oil Pressure Warning
Engine Oil Level Warning
Malfunction Indicator
ABS Indicator
No.
Combination Meter (Terminal B2)
ECM
ECM
Low Oil Pressure Warning Switch
Combination Meter (Terminal B4)
TRAC ECU, Traction Solenoid Relay
Ground
Theft Deterrent and Door Lock ECUWire Harness Side
1
2
3
4
5
6
8
9
10
No.Wire Harness Side
GAUGE Fuse
ECU-B Fuse
IGN Fuse
PANEL Fuse
Vehicle Speed Sensor (Terminal 3)
Ground
DOME Fuse
Light Control Rheostat
Combination Meter (Terminal B1)
Generator Terminal
Door Courtesy Switch
Integration Relay (Terminal 9)
Light Failure Sensor Center Airbag Sensor 1
2
3
4
5
6
8
107
11
12
14
15
16
18GAUGE Fuse
PPS ECU, Cruise Control ECU, ECM OD/TRIP
Meter
Open Door Warning
Seat Belt Warning
SRS Warning 8
6 5
3
4
110
2 9
7
10
5
14
18
12
16
15
114
6
1
8
3
2Air Conditioning Amplifier Telltale Light LH:
Telltale Light RH:
Rear Light Warning
Discharge Warning BE-42
- BODY ELECTRICALCOMBINATION METER
2020 Author
: Date
:
1997 SUPRA (RM502U)
2. TELLTALE LIGHT:

N08953
N08954
BE6219
Junction Block Side
Connector ºAº
- BODY ELECTRICALCOMBINATION METER
BE-51
2029 Author
: Date
:
1997 SUPRA (RM502U)
26. INSPECT INTEGRATION RELAY OPERATION
(a) Connect the positive (+) lead from the battery to terminals
1 and 7.
(b) Connect the positive (+) lead from the battery to terminal
9 through a 3.4 W test bulb.
(c) Check that the test bulb lights up and buzzer sounds for
4 - 8 seconds when the negative (-) lead from the battery
is connected to terminal 10.
(d) Check that the buzzer sounding in (c) stops when the
negative (-) lead from the battery is connected to terminl
8.
If operation is not as specified, replace the integration relay.
27. INSPECT RELAY CIRCUIT
Remove the relay from the junction block No. 1 and inspect the
connectors on the junction block side.
Tester connectionConditionSpecified condition
4 - GroundDriver's door openContinuity
4 - GroundDriver's door closeNo continuity
5 - GroundIgnition key SetContinuity
5 - GroundIgnition key removeNo continuity
8 - GroundDriver's seat belt fastenContinuity
8 - GroundDriver's seat belt unfastenNo continuity
10 - GroundConstantContinuity
1 - GroundConstantBattery positive voltage
9 - GroundIgnition switch position ONBattery positive voltage
9 - GroundIgnition switch position LOCK or ACCNo Voltage
If circuit is not as specified, tray replacing the relay with a new
one.

Z10792
N09810
N09811
N09812
N09813
BE-62
- BODY ELECTRICALPOWER WINDOW CONTROL SYSTEM
2040 Author
: Date
:
1997 SUPRA (RM502U)
5. INSPECT POWER WINDOW SWITCH CONTINUITY
Switch positionTester connectionSpecified condition
UP1 - 4, 3 - 5Continuity
OFF1 - 2, 3 - 5Continuity
DOWN1 - 2, 3 - 4Continuity
If continuity is not as specified, replace the switch.
6. Driver 's Door:
INSPECT POWER WINDOW MOTOR OPERATION
(a) Connect the positive (+) lead from the battery to terminal
1 and the negative (-) lead to terminal 2, and check that
the motor turns clockwise.
(b) Reverse the polarity, and check that the motor turns coun-
terclockwise.
If operation is not as specified, replace the motor.
7. Passenger 's Door:
INSPECT POWER WINDOW MOTOR OPERATION
(a) Connect the positive (+) lead from the battery to terminal
1 and the negative (-) lead to terminal 2, and check that
the motor turns clockwise.
(b) Reverse the polarity, and check that the motor turns coun-
terclockwise.
If operation is not as specified, replace the motor.

BO0QC-01
N19534
Outside Handle
Door Lock CylinderDoor Glass
Belt Moulding
Outer Rear View Mirror
Door Hinge
Door Check Door Window Upper Stop
Door Lock
Door Hinge
Weatherstrip
Glass Guide
Service Hole Cover Inside Panel
Frame
Window Regulator
Armrest Bracket
Setting Nut
Window Guide
Lower PlateInside Handle
Plate
Trim BoardInside Handle
Speaker
Power Window Switch
(Passenger's) Inside Handle Bezel
Power Window Master Switch

Precoated part
7.4 (76, 67 in.´lbf)
11 (115, 8.3)
52 (530, 38)
25 (260, 19)
5.0 (51, 44 in.´lbf)
5.4 (55, 48 in.´lbf)7.4 (76, 67 in.´lbf)
N´m (kgf´cm, ft´lbf): Specified torque
- BODYFRONT DOOR
BO-7
2087 Author
: Date
:
1997 SUPRA (RM502U)
FRONT DOOR
COMPONENTS

BO0QD-01
N08444
Vehicle
Outside Inside
N08445
N19391
: 6 Clips
N08456
Snap Snap
Setting NutLower Plate BO-8
- BODYFRONT DOOR
2088 Author
: Date
:
1997 SUPRA (RM502U)
DISASSEMBLY
1. REMOVE INSIDE HANDLE BEZEL
Remove the screw, then pull the inside handle bezel.
2. REMOVE TRIM BOARD
3. REMOVE THESE PARTS:
(a) Power window master switch
(b) Speaker
(c) Inside handle
(d) Inside handle plate
(e) Armrest bracket
(f) Service hole cover
(g) Weatherstrip
(h) Inside panel frame
(i) Door glass
Torque: 7.4 N´m (76 kgf´cm, 67 in.´lbf)
4. REMOVE DOOR BELT MOULDING
(a) Remove the clip.
(b) Using a screwdriver, remove the door belt moulding as
shown in the illustration.
HINT:
Tape the screwdriver tip before use.
5. REMOVE WINDOW GUIDE LOWER PLATE
(a) Remove the bolt of the lower plate and connector.
Torque: 5.4 N´m (55 kgf´cm, 48 in.´lbf)
(b) Unlock the snap by pulling the lower plate.
(c) Remove the snap and lower plate from the stud bolt of the
lower bracket.
(d) Remove the setting nut from the lower bracket.

N19389
N19532
0 - 1.0 mm
(0 - 0.04 mm)
N19388
- BODYFRONT DOOR
BO-9
2089 Author
: Date
:
1997 SUPRA (RM502U)
6. REMOVE WINDOW REGULATOR
(a) Disconnect the connector.
(b) Remove the bolt, 2 nuts and window regulator.
Torque: 7.4 N´m (76 kgf´cm, 67 in.´lbf)
HINT:
At the time of reassembly, please refer to the following item.
Apply MP grease to the glass guide and rollers of the window
regulator.
7. REMOVE DOOR LOCK
(a) Disconnect the connector and clamp.
(b) Disconnect the link from the outside handle.
HINT:
At the time of reassembly, please refer to the following item.
After connecting the link, check that the clearance is within the
specification as shown in the illustration.
(c) Remove the 3 screws.
Torque: 5.0 N´m (51 kgf´cm, 44 in.´lbf)
HINT:
At the time of reassembly, please refer to the following item.
Apply adhesive to the 3 screws.
Part No.08833-00070, THREE BOND 1324 or equiva-
lent.
(d) Remove the door lock through the service hole.
HINT:
At the time of reassembly, please refer to the following item.
Apply MP grease to the sliding and rotating parts of the door
lock.
8. REMOVE THESE PARTS:
(a) Outside handle
(b) Door lock cylinder
(c) Outer rear view mirror

BO0QE-01
N16816
SST
N16815
SST
N08443
N11799
BO-10
- BODYFRONT DOOR
2090 Author
: Date
:
1997 SUPRA (RM502U)
ADJUSTMENT
1. ADJUST DOOR IN FORWARD/REARWARD AND VER-
TICAL DIRECTIONS
Using SST, adjust the door by loosening the body side hinge
bolts.
SST 09812-00020
Torque: 52 N´m (530 kgf´cm, 38 ft´lbf)
2. ADJUST DOOR IN LEFT/RIGHT AND VERTICAL
DIRECTIONS
Using SST, adjust the door by loosening the door side hinge
bolts.
SST 09812-00010
HINT:
Substitute the standard bolt for the centering bolt.
(See page BO-6)
Torque: 25 N´m (260 kgf´cm, 19 ft´lbf)
3. ADJUST DOOR LOCK STRIKER
(a) Check that the door fit and door lock linkages are adjusted
correctly.
(b) Using a screwdriver, remove the striker cover.
(c) Using a torx wrench, loosen the striker mounting screws.
(d) Using a brass bar and hammer, tap the striker to adjust it.
CAUTION:
Do not tap the striker too hard.

N08480
Door Window
Upper StopDoor Window
Upper Stop
Carrier Plate
Guide Lower Bracket
Lower Plate
N08475
Setting NutSnap
Lower Plate
N08477
N08845
BO-12
- BODYFRONT DOOR
2092 Author
: Date
:
1997 SUPRA (RM502U)
5. ADJUST FRONT DOOR GLASS

Upper side of glass - in/out
(1) Remove the lower plate bolt.
(2) Pull the lower plate so that the snap is unlocked.
(3) Remove the snap and lower plate.
(4) Adjust the glass by turning the setting nut.
(5) Reinstall the lower plate, snap and bolt.
Torque: 5.4 N´m (55 kgf´cm, 48 in.´lbf)

Position (forward/rearward) the glass and attitude of
glass
Loosen the 3 bolts of the carrier plate and adjust.
Torque: 7.4 N´m (76 kgf´cm, 67 in.´lbf)

Position (vertical) the glass and attitude of glass
(when glass fully closed)
Adjust the door window upper stop.
Torque: 11 N´m (115 kgf´cm, 8.3 ft´lbf)