Page 182 of 1807
BE0DY-02
Z09367
Right Turn
Left Turn
Connector ºAº
BE1843
2
Turn Signal Light Bulbs (21W)13
Z09334
BE-26
- BODY ELECTRICALTURN SIGNAL AND HAZARD WARNING SYSTEM
2004 Author: Date:
1997 SUPRA (RM502U)
INSPECTION
1. INSPECT TURN SIGNAL SWITCH CONTINUITY
Switch positionTester connectionSpecified condition
Left turnA1 - A5Continuity
Neutral-No continuity
Right turnA1 - A8Continuity
If continuity is not as specified, replace the switch.
2. INSPECT TURN SIGNAL FLASHER OPERATION
(a) Connect the terminal 2 to battery positive (+) terminal and
the terminal 3 to battery negative (-) terminal.
(b) Connect the 2 turn signal light bulbs parallel to each other
to terminals 1 and 3, check that the bulbs flash.
HINT:
The turn signal lights should flash between 60 and 120 times
per minute.
3. INSPECT HAZARD WARNING SWITCH CONTINUITY
ConditionTester connectionSpecified condition
Switch OFF7 - 10Continuity
Switch ON7 - 8
4 - 5 - 6 - 9Continuity
Illumination circuit2 - 3Continuity
If continuity is not as specified, replace the switch.
BE3QR-01
Page 184 of 1807
BE0E0-02
N08914
1
3
N08913
1
2
N08920
N08130
N08912
BE-28
- BODY ELECTRICALINTERIOR LIGHT SYSTEM
2006 Author: Date:
1997 SUPRA (RM502U)
INSPECTION
1. INSPECT INTERIOR LIGHT CONTINUITY
Switch positionTester connectionSpecified condition
DOOR1 - 3Continuity
OFF-No continuity
2. INSPECT PERSONAL LIGHT CONTINUITY
Switch positionTester connectionSpecified condition
OFF-No continuity
*ON1 - 2Continuity
* Set the interior light switch to OFF or DOOR.
If continuity is not as specified, replace the light assembly or
bulb.
3. INSPECT LUGGAGE ROOM LIGHT CONTINUITY
Switch positionTester connectionSpecified condition
OFF1 - 2No continuity
ON1 - 2Continuity
If continuity is not as specified, replace the light.
4. INSPECT DOOR COURTESY SWITCH CONTINUITY
Switch positionTester connectionSpecified condition
ON (SW pin released)1 - 2 - 3Continuity
OFF
(SW pin pushed in)-No continuity
If continuity is not as specified, replace the switch.
5. INSPECT LUGGAGE ROOM LIGHT SWITCH CONTI-
NUITY
ConditionTester connectionSpecified condition
ON (SW pin released)1 - Switch bodyContinuity
OFF
(SW pin pushed in)1 - Switch bodyNo continuity
If continuity is not as specified, replace the switch.
Page 196 of 1807
BE0E8-01
I02077
Connector ºCº Connector ºBº Connector ºAº
Bulb Check Relay
BE-40
- BODY ELECTRICALCOMBINATION METER
2018 Author: Date:
1997 SUPRA (RM502U)
CIRCUIT
1. METER:
Page 197 of 1807
I02078
Cruise Control Indicator :Fuel Gauge
:Engine Coolant Temperature Gauge
:Tachometer
:Speedometer
D.R.L. :Daytime Running Light
* :Engine Oil Level Delay Circuit
F
E
T
S
F
E
T
S C8
A10
A11
A9
A8
A13
C11
C10
B13
B12
B2
A1
C7
C5
A14
A7
A6
A3
C1
C2
C13
A5P
R
N
D
2
LB4
B10
B6
B7
B8
B11
B1
C9
A16
C4
C6
A15
A2
B3
C12 Fuel Level Warning
MANU Indicator
O/D OFF Indicator
Brake Warning
Bulb Check Relay
TRAC Indicator
Right Turn Indicator
High Beam Indicator
Master Warning
Illumination
SNOW IndicatorLeft Turn Indicator
No. Wire Harness Side
Brake Fluid Level Warning Switch
Parking Brake Switch
USA:TAIL (RH) Fuse, PANEL Fuse
Headlight Dimmer Switch
ECT ECU
Cruise Control ECU
TRAC ECU
Ground (Engine)
Engine Coolant Temperature Sender Gauge
Fuel Sender Gauge
Ground (Signal)
Turn Signal Switch
Starter Relay Generator L Terminal Igniter
Park/Neutral Position Switch (A/T Vehicle) A1
2
3
5
6
7
8
9
10
11
13
14
15
16
BGAUGE Fuse
O/D OFF Switch
USA:TAIL (RH) Fuse, PANEL Fuse
Park/Neutral Position Switch (P)
Park/Neutral Position Switch (N)
ECT ECU
Ground (Power)
Park/Neutral Position Switch (D)
Park/Neutral Position Switch (2)
Park/Neutral Position Switch (L) Park/Neutral Position Switch (R) 1
2
3
6
7
8
10
11
124
13
Engine Oil Level Sensor
Turn Signal Switch
Ground (Power)
Fuel Sender Gauge
GAUGE Fuse
Vehicle Speed Sensor (Terminal 2)
Vehicle Speed Sensor (Terminal 3)
USA:TAIL (RH) Fuse, PANEL Fuse
Light Control Rheostat Telltail Light RH (Terminal 11)
Telltail Light LH (Terminal 1)
Telltail Light LH (Terminal 6) 1
2
6
7
8
10
11
124
135
9 CCANADA:D.R.L. No.3 Relay
Clutch Start Switch (M/T Vehicle)
CANADA:D.R.L. No.3 Relay
CANADA:D.R.L. No.3 Relay
- BODY ELECTRICALCOMBINATION METER
BE-41
2019 Author: Date:
1997 SUPRA (RM502U)
Page 200 of 1807
N08931
N08967
Ignition
Switch
Fuel
Gauge
Battery
Z09321
Fuel Gauge
Battery BE-44
- BODY ELECTRICALCOMBINATION METER
2022 Author: Date:
1997 SUPRA (RM502U)
4. INSPECT OD/TRIP METER (in Telltale Light RH)
(a) Remove the telltale light with connector still connected.
(b) Check the continuity and voltage.
Tester connectionConditionSpecified condition
7 - Ground*1ConstantContinuity
1 - Ground*1Ignition Switch ºONº positionBattery positive voltage
4 - Ground*1Light Control Switch ºTAILº or ºHEADº
positionBattery positive voltage
5 - 7*1Ignition Switch ON
Drive the vehicle slowly0V e Battery positive voltage
6 - 7*2Ignition Switch ON
Drive the vehicle slowly0V e more than 5V
8 - Ground*1ConstantBattery positive voltage
10 - Ground*1Ignition Switch ON, Light Control Switch TAIL or
HEAD, Turn the light control rheostat knob to
clockwise
6V " 0V
*1: If continuity or voltage are not as specified, check vehicle
side.
*
2: If voltage is not as specified, replace the telltale light.
5. INSPECT FUEL RECEIVER GAUGE OPERATION
(a) Disconnect the connector from the sender gauge assem-
bly.
(b) Turn the ignition switch ON, check that the receiver gauge
needle indicates EMPTY.
(c) Connect terminals 2 and 3 on the wire harness side con-
nector through a 3.4 W test bulb.
(d) Turn the ignition switch ON, and check that the bulb lights
up and that receiver gauge needle moves toward the full
side.
HINT:
Because of the silicon oil in the gauge, it will take a short time
for the needle to stabilize.
If operation is not as specified, inspect the receiver gauge resis-
tance.
Page 201 of 1807
N08911
B
AC
N08959
F
1/2
E
Z09401
Ignition
Switch
BatteryWarning Light
N08933
N08993
- BODY ELECTRICALCOMBINATION METER
BE-45
2023 Author: Date:
1997 SUPRA (RM502U)
6. INSPECT FUEL RECEIVER GAUGE RESISTANCE
Measure the resistance between terminals.
Between terminalsResistance (W)
A - BApprox. 269.7
A - CApprox. 123.5
B - CApprox. 146.2
If resistance value is not as specified, replace the fuel receiver
gauge.
7. INSPECT FUEL SENDER GAUGE RESISTANCE
Measure the resistance between terminals 2 and 3 for each
float position.
Float position: mm (in.)Resistance (W)
F: Approx. 33.8 (1.331)Approx. 4.0
1/2: Approx. 44.8 (1.764)Approx. 55.0
E: Approx. 141.1 (5.555)Approx. 107.0
If resistance value is not as specified, replace the sender
gauge.
8. INSPECT FUEL LEVEL WARNING LIGHT
(a) Disconnect the connector from the sender gauge.
(b) Connect terminals 1 and 3 on the wire harness side con-
nector.
(c) Turn the ignition switch ON, check that the warning light
lights up.
If the warning light does not light up, test the bulb or inspect wire
harness.
9. INSPECT FUEL LEVEL WARNING SWITCH OPERA-
TION
(a) Apply battery positive voltage between terminals 1 and 3
through a 3.4 W test bulb, check that the bulb lights up.
HINT:
It will take a short time for the bulb to light up.
(b) Submerge the switch in fuel, check that the bulb goes out.
If operation is not as specified, replace the sender gauge.
Page 202 of 1807
Z07423
Ignition
Switch
Battery Engine Coolant Temperature Gauge
Sender
Gauge
Z14747
Battery Engine Coolant Temperature Gauge
Test Bulb
(3W)
Z09421
A
BC
N15887
BE-46
- BODY ELECTRICALCOMBINATION METER
2024 Author: Date:
1997 SUPRA (RM502U)
10. INSPECT ENGINE COOLANT TEMPERATURE RE-
CEIVER GAUGE OPERATION
(a) Disconnect the connector from the sender gauge.
(b) Turn the ignition switch ON, check that the receiver gauge
needle indicates COOL.
(c) Ground terminal on the wire harness side connector
through a 3 W test bulb.
(d) Turn the ignition switch ON, check that the bulb lights up
and that the receiver gauge needle moves toward the hot
side.
If operation is as specified, replace the sender gauge.
Then recheck the system.
If operation is not as specified, measure the receiver gauge re-
sistance.
11. INSPECT ENGINE COOLANT TEMPERATURE RE-
CEIVER GAUGE RESISTANCE
Measure the resistance between terminals.
HINT:
Connect the test leads so that the current from the ohmmeter
can flow according to the chart order.
Between terminalsResistance (W)
A - BApprox. 229.7
A - CApprox. 54.0
B - CApprox. 175.7
If resistance value is not as specified, replace the engine cool-
ant temperature receiver gauge.
12. INSPECT ENGINE COOLANT TEMPERATURE SEND-
ER GAUGE RESISTANCE
Measure the resistance between terminal and gauge body.
Temperature °C (°F)Resistance (W)
50 (122.0)160 ~ 240
120 (248.0)17.1 ~ 21.2
If resistance value is not as specified, replace the engine cool-
ant temperature sender gauge.
Page 203 of 1807
N06640
BE0044
Ignition
Switch
BatteryWarning Light
N09645
ON
OFF
N09646
ON
OFF
Z07431
Ignition
Switch
BatteryWarning Light
- BODY ELECTRICALCOMBINATION METER
BE-47
2025 Author: Date:
1997 SUPRA (RM502U)
13. INSPECT LOW OIL PRESSURE SWITCH CONTINUITY
(a) Check that there is continuity between terminal and
ground with the engine stopped.
(b) Check that there is no continuity between terminal and
ground with the engine running.
HINT:
Oil pressure should be over 29 kPa (0.3 kgf/cm
2, 4.3 psi)
If operation is not as specified, replace the switch.
14. INSPECT LOW OIL PRESSURE WARNING LIGHT
(a) Disconnect the connector from the warning switch and
ground terminal on the wire harness side connector.
(b) Turn the ignition switch ON, check that the warning light
lights up.
If the warning light does not light up, test the bulb or inspect wire
harness.
15. INSPECT ENGINE OIL LEVEL WARNING SWITCH
CONTINUITY
(a) Check that there is continuity between terminal with the
switch in each position.
(b) Heat the switch to above 60°C (140°F) in an oil bath.
(c) Check that there is continuity between terminals with the
switch ON (float up).
(d) Check that there is no continuity between terminals with
the switch OFF (float down).
If operation is not as specified, replace the switch.
16. INSPECT ENGINE OIL LEVEL WARNING LIGHT
(a) Disconnect the connector from the switch.
(b) Ground terminal 1 on the wire harness connector.
(c) Turn the ignition switch ON. Check that the warning light
lights up approximately 40 seconds later.
If the warning light does not light up, inspect bulb or wire har-
ness.
