1997 TOYOTA PASEO tow

Publication No. OM16514U
Part No. 01999-16514
Printed in Japan 01- 9701- 00
Quick index If a service reminder indicator or warning buzzer comes on 67 . . . . .
If your vehicle will not start 119
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
If your engine stalls while driving 122 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
If your vehicle overheats 123
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
If you have a flat tire 124
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
If your vehicle needs to be towed 131 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tips for driving during break- in period 101 . . . . . . . . . . . . . . . . . . . . . . . . .
How to start the engine 113
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
General maintenance 142
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Complete index 181
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Gas station information
Fuel type: UNLEADED gasoline , Research Octane Number 91 (Octane Rating)
or higher See page 101 for detailed information.
Fuel tank capacity:
45 L (11.9 gal., 9.9 lmp. gal.)
Engine oil:
API SH, energy- Conserving llº multigrade engine oil or ILSAC multig rade
engine oil is recommended.
Use SAE 5W- 30 if normal temperatures are above -18 C (0 F).
See page 154 for detailed information.
Tire information: See pages 157 through 161.
Tire pressure: See page 175. P
8
B

11
To open the trunk lid from the outside, insert the master key and turn it clock- wise. See ºLuggage stowage precautionsº in
Part 2 for precautions to observe in load- ing luggage.
To close the trunk lid, lower it and press
down on it. After closing the trunk lid, try
pulling it up to make sure it is securely closed.
CAUTION!
Keep the trunk lid closed while driv-
ing. This not only keeps the luggage
from being thrown out but also pre-vents exhaust gases from entering
the vehicle.
To open the trunk lid from the driver's
seat, pull up on the lock release lever.
Trunk lidÐ
ÐLock release lever

18
3. Push in the retaining springs armsas shown and push up the moon roof.1. Press in the rearing spring armsand insert them in the holes to lock
the handle securely.2. Place the moon roof with sunshade on the stowage bag.
When placing them, be sure the interior
side of the moon roof facing downward.
ÐStowing

19
3. Fold the stowage bag in half andzip. Put the stowage belt through
the retaining clip.
4. Put the stowage bag in the trunkroom. Then attach the hooks to the
stowage anchor.
When putting the stowage bag in the trunk
room, be sure the side attached the cau- tion label facing upward.
CAUTION!
Be sure to place the moon roof cor-
rectly. Placing incorrectly may cause a damage and possibly per-
sonal injury.
Make sure both hooks are securely
attached to the stowage anchor.
NOTICE
Be sure that the luggages in the
trunk room do not hit on the
stowed moon roof.
To avoid damaging the moon roof,do not press on the center of the
stowed moon roof and do not
place anything heavy on thestowed moon roof.

29
For easy access to the rear seat, do this.
1. Lift the seatback angle adjusting leveror press the pedal behind the seat- back.
The seat will slide forward slightly.
2. Move the seat to the front-most posi- tion.
After passengers are in, lift up the seat- back and return the seat until it locks
CAUTION!
After pulling back the seat, try
pushing the seat forward and rear-
ward to make sure it is secured inplace.
Never allow anyone to rest their
foot on the release pedal while the
vehicle is moving.
1. Pull up the seatback security lock
lever 1 to the unlock position.
2. Pull out the lock release strap 2.
3 Fold down the seatback. This will enlarge the trunk room as far as the front seatbacks. See Luggage stow-
age precautionsº in Part 2 for precautions
to observe in loading luggage.
ÐMoving passenger's seat for rear seat entry (2-door models)
Fold-down rear seat
(coupe only)

60
High-Low beamsÐFor high beams,
turn the headlights on and push the lever away from you (position 1). Pull the lever toward you (position 2) for low beams.
The headlight high beam indicator light
(blue light) on the instrument panel will tell
you that the high beams are on.
Flashing the high beam headlights
(position 3)ÐPull the lever all the way
back. The high beam headlights turn off
when you release the lever.
You can flash the high beam headlights with the knob turned to OFFº.TURN SIGNALS
To signal a turn, push the headlight/
turn signal lever up or down to posi-
tion 1. The key must be in the ONº position. The lever automatically returns after you make a turn, but you may have to returnit by hand after you change lanes.
To signal a lane change, move the lever
up or down to the pressure point (position2) and hold it.
If the turn signal indicator lights (green
lights) on the instrument panel flash faster
than normal, a front or rear turn signal bulb has burned out.To turn on the emergency flashers,
push the switch.
All the turn signal lights will flash. To turn
them off, push the switch once again.
Turn on the emergency flashers to warn other drivers if your vehicle must be
stopped where it might be a traf fic hazard.
Always pull as far off the road as possible.
The turn signal light switch will not work
when the emergency flashers are operat- ing.
Emergency flashers

68(a) Brake System Warning Light This light has the following functions: Parking brake reminder
If this light is on, make sure the parking
brake is
fully released. The light should go
off.
Low brake fluid level warning
If this light comes on and stays on while
you are driving, slow down and pull off the
road. Then stop the vehicle carefully.There may be a problem somewhere in
the brake system. Check the fluid level of
the see-through reservoir.
To make sure the parking brake has not
caused the warning light to come on,
check to see that the parking brake is fully
released.
If the brake fluid level is low...
At a safe place, test your brakes by start-
ing and stopping. If you judge that the brakes still work
adequately, drive cautiously to yournearest dealer or shop for repairs.
If the brakes are not working, have the
vehicle towed in for repairs. (For tow-
ing information, see Part 4.)
It is dangerous to continue driving
normally when the brake fluid level
is low. CAUTION
!
If the brake fluid level is correct...
Have the warning system checked by
your Toyota dealer. (b) Seat Belt Reminder Light and Buzzer
Once the ignition key is turned to ONº or
STARTº, the reminder light and buzzer
come on if the driver's seat belt is not fas-tened. Unless the driver fastens the belt,
the light stays on and the buzzer stops af-
ter about 4 to 8 seconds.
(c) Discharge Warning Light
This light warns that the battery is being discharged.
If it comes on while you are driving, there
is a problem somewhere in the charging system.
The engine ignition will continue to oper-
ate, however, until the battery is dis-
charged. Turn off the air conditioning,
blower, radio, e tc., and drive directly to the
nearest Toyota dealer or repair shop.NOTICE
Do not continue driving if the engine drive belt is broken or loose.
(d) Low Oil Pressure Warning Light
This light warns that the engine oil pres-
sure is too low.
If it flickers or stays on while you are driv-
ing, pull off the road to a safe place and
stop the engine immediately. Call a Toyo-
ta dealer or qualified repair shop for assis-tance.
The light may occasionally flicker when
the engine is idling or it may come on brief-
ly after a hard stop. There is no cause for concern if it then goes out when the en-
gine is accelerated slightly.
The light may come on when the oil level
is extremely low. It is not designed to indi- cate low oil level, and the oil level must bechecked using the level dipstick.
NOTICE
Do not drive the vehicle with the warning light onÐeven for one
block. It may ruin the engine.

73
Your automatic transmission has a shift
lock system to minimize the possibility of
incorrect operation. This means you can
only shift out of Pº position when the brake
pedal is depressed (with the ignition
switch in ONº position and the lock re-
lease button depressed). (a) Normal driving
1. Start the engine as instructed in How
to start the engineº in Part 3. The trans-mission must be in Pº or Nº.
2. With your foot holding down the brake
pedal, shift the selector lever to Dº.
In Dº position, the automatic transmis-
sion system will select the most suitable
gear for running conditions such as nor-
mal cruising, hill climbing, hard towing, etc.
Always turn the overdrive switch on for
better fuel economy and quieter driving. If
the engine coolant temperature is low, thetransmission will not shift into the over-
drive gear even with the overdrive switch on.
Never put your foot on the accelera-
tor pedal while shifting. CAUTION
! 3. Release the parking brake and brake
pedal. Depress the accelerator pedal
slowly for smooth starting.
(b) Using engine braking
To use engine braking, you can downshift the transmission as follows: Turn off the overdrive switch. The O/D OFFº indicator light will com on and the
transmission will downshift to the third
gear.
Shift into the 2º position when the ve-
hicle speed is lower than the 70 km/h
(43 mph). The transmission will down-
shift to the second gear and more en-gine braking will be obtained.
Shift into the Lº position when the ve-
hicle speed is lower than 40 km/h (25
mph). The transmission will downshiftto the first gear and maximum enginebraking will be applied.
Vehicles with cruise controlÐWhen the
cruise control is being used, even if you
downshift the transmission by turning off the overdrive switch, engine braking will
not be applied because the cruise control
is not cancelled. For ways to decrease the
vehicle speed, see Cruise controlº in this
chapter.
Be careful when downshifting on a
slippery surface. Abrupt shifting
could cause the vehicle to spin orskid. CAUTION
!
(c) Using the 2º and Lº positions
The 2º and Lº positions are used for
strong engine braking as described pre-
viously. With the selector lever in 2º or Lº, you
can start the vehicle in motion as with the
lever in Dº. With the selector lever in 2º, the vehicle
will start in the first gear and automatically
shift to the second gear.
With the selector lever in Lº, the trans-
mission is engaged in the first gear.