1997 SSANGYONG KORANDO oil capacity

1A3 -- 2 GENERAL ENGINE INFORMATION
D AEW OO M Y_2000
ENGINE SPECIFICATIONS (Cont’d)
ApplicationOM662LAOM661LA
Idle Speed (rpm)720 -- 820750 -- 850
Fuel Injection Pressure (bar)135 -- 143135 -- 143
Oil Capacity (liter)8.0 -- 9.56.5 -- 8.0
Lubrication TypeForced by Gear PumpForced by Gear Pump
Oil Filter TypeCombined Full-- Flow and Partial
Flow FilterCombined Full-- Flow and Partial
Flow Filter
FuelDieselDiesel

SSAMGYONG MY2002
3A-2 FRONT AXLE
M/T
A/T
M/T
A/T
M/T
A/T
M/T
A/T
SPECIFICATIONS
GENERAL SPECIFICATIONS
Application
Drive Shaft Type
Axle Housing Type
Differential Type
Differential GearCV Joint
Build - up
Conventional
Hypoid Gear
4.56
5.38
4.27
4.89
4.55
5.86
3.73
4.89
1.3 L
SEA 80W/90, API GL - 5Description
661LA
662LA
E23
E32 Reduction Ratio
Oil Capacity
Oil Specification
FASTENER TIGHTENING SPECIFICATIONS
Steering Knuckle and Drive Shaft
36.8 - 44.2
18.4 - 25.8
51.6 - 66.3
11.0
-
62.7 - 77.4 Drive Shaft Cover Bolt
Drive Shaft to Front Axle Inner Shaft
Hub Flange Bolt
Hub Nut
Locking Hub Washer Screw
Wheel Speed SensorN
z zz z
zm ApplicationLb-InLb-Ft
50 - 60
25 - 35
70 - 90
15
2 - 4
85 - 105-
-
-
-
17.7 - 35.4
-

SSANGYONG MY2002
3D-2 REAR AXLE
Disc Brake
Drum Brake50 - 65
4 - 8
85 - 105
50 - 65
150 - 180
30 - 45
30 - 45
150 - 180
150 - 180
70 - 80
12 - 23
6 - 8
1 - 19Lb-Ft Axle Shaft Type
Axle Housing Type
Differential
Reduction Ratio
OilType
Gear
Gasoline + M/T
Diesel + M/T
Gasoline + A/T
Diesel + A/T
Capacity
SpecificationSemi-floating
Build up
Conventional Type
Hypoid Gear
3.73
4.27
4.56
4.89
1.9
SAE 80W/90 or API GL-5
GENERAL DESCRIPTION AND OPERATION
SPECIFICATIONS
37 - 48
35 - 71
63 - 77
37 - 48
111 - 133
22 - 23
22 - 23
111 - 133
111 - 133
52 - 59
9 - 17
53 - 71
11 - 14 Flange fixing Bolt
Dust shield Bolt
Caliper Bolt
Fixing NutN
z zz z
zm ApplicationLb-In
-
-
-
-
-
-
-
-
-
-
-
-
-
FASTENER TIGHTENING SPECIFICATIONS
Rod Bolt
Shock absorber Bolt
Stabilizer bar cap bolt
Upper arm nut
Lower arm nut
Propeller shaft fixing bolt
LCRV Mounting Bolt
Air Breather Hose Bolt
Brake oil pipe (M10)

MANUAL TRANSMISSION 5B-3
SSANGYONG MY2002
Model
Type
Gear Ratio
Oil
Weight (Dry)1st
2nd
3rd
4th
5th
Reverse
Specification
Capacity(litre)
Change Interval Application
SPECIFICATIONS
T5WC
Floor Change
3.969 : 1
2.341 : 1
1.457 : 1
1.000 : 1
0.851 :1
3.710 : 1
ATF DEXRON II / III
3.4 L
Check : Every 15,000 km,
Replace : Every 50,000 km
33kg
Description
Notice: Add LUBRIZOL (280cc) in oil after overhauling.

MANUAL TRANSMISSION 5B-23
SSANGYONG MY2002
4. Install the front and rear propeller shafts to the
transmission.
Installation Notice
5. Connect the cable, the harness and the bleeder.
6. Install the back lamp switch.
7. Install the speedometer cable.
YAD5B430
YAD5B440
YAD5B450
YAD5B310
81 - 89 Nm
(60 - 66 lb-ft)
70 - 90 Nm
(52 - 66 lb-ft)
Tightening
TorqueFront
Rear
8. Charge the approved oil in the transmission
housing and tighten the drain plug and the filler
plug.
Installation Notice
Oil25 Nm (18 lb-ft)
25 Nm (18 lb-ft)
Tightening
TorqueFiller Plug
Drain Plug
Spec.
Capacity
3.4L
2.0L
4WD
2WDATF Dexron II

TRANSFER CASE (PART TIME - 4408) 5D2-9
SSANGYONG MY2002
Model
Type
Gear Ratio
Oil
Manufacturer
WeightHigh
Low
Specification
Capacity
Lubrication
SPECIFICATIONS
Part-Time 4408 (E)
E.S.O.F. Type
1 : 1
2.48 : 1
ATF S-3, S-4 or DEXRON II, III
1.2 L
Check : Every 10,000 km
Replace : Every 60,000 km
Borg Warner
30 kg

SSANGYONG MY2002
7C-2 MANUAL & SEMIAUTO-HVAC
SPECIFICATIONS
REFRIGERANT
Core Size (LxWxT)
Core Type
Expansion Valve Type
Thermostat
Resister Type
Cooling CapacityApplicationDescription237.0 x 232.0 x 92.0
Aluminum plate
Angle
ON:4.5 ± 0.6°C, OFF:1.5 ± 0.6°C
Aluminum plate
4,300 Kcal/h (AT 420 CMH)
Capacity
TypeApplicationDescription650 - 750 g
R134a
EVAPORATOR UNIT
BLOWER UNIT
Motor Type
Motor SizeApplicationDescriptionMagnetic
φ 70 x
145
COMPRESSOR
Model
Type
Displacement (cc/rev.)
PCD (Pulley Center Diameter)
Oil
Magnetic clutch outputApplicationDescriptionFK-II (DKV 14C)
Vane rotary type
140.5 (cc/rev)
φ 143
ZXL 200 PG (PAG Oil)
45 W
CONDENSER
Size (WxHxT)
Capacity
TypeApplicationDescription650 x 339.2 x 22.0
11,000 Kcal/h
Parallel Flow
RECEIVER DRIER
Material
Capacity
DesiccantApplicationDescriptionAluminum
250 cc
XH-9 (35 g)

SSANGYONG MY2002
7C-18 MANUAL & SEMIAUTO-HVAC
Total Oil Capacity 265 cc
COMPRESSOR OIL
REPLACEMENT
Before Oil Replacement
When any part is replaced or there are a lot of gas
leaks in the A/C system, you should add the specified
amount of the oil to keep the approval oil capacity
because the oil for lubricating the compressor
circulates through the A/C system during operating
the compressor.
Handling Oil
Be careful that moistures, dusts etc. must not flow
into the oil.
Do not mix with any other material.
If the oil leaves outside for long time, it’s possible
to mix it with the moistures and so keep the oil
sealed with a container.
Circulating Oil
For checking or adjusting the oil level, set the control
unit to full cold and max blower speed with keeping
the engine run at idle for 20 - 30 minutes in order to
circulate the oil through the compressor.