1997 RENAULT KANGOO ABS

UPPER FRONT STRUCTURE
Wheel arch, front section
42E
PRB4212
INTRODUCTION
The replacement of this part is an operation for a
frontal impact and is complementary to the repla-
cement of the cowl side panel (pillar lining).
It can be carried out partially from the right hand
side (see diagram and method below).
In the operation described below there are only
descriptions of the joints specific to the part
concerned.
Information concerning other parts will be dealt
with in the respective section.
COMPOSITION OF THE PART FROM THE PARTS
DEPARTMENT
1 - Part only (right hand side).
2 - Part only (left hand side).
JOINTS WITH :
Engine mounting height adjuster (right hand side)
Shock absorber cup height adjuster
Side member closure panel
Front end lower cross member (right hand side)
Cowl side panel (pillar lining)
PARTS CONCERNED (thickness in mm):
1Engine mounting 2
2Shock absorber cup height adjuster 2
3Side member closure panel 1
4Side member, front section 1.5
5Front wheel arch 1
6Front end lower cross member 1.5
7Cowl side panel (pillar lining) 1.5
or
42-12

UPPER FRONT STRUCTURE
Wheel arch
42F
PRB4213
INTRODUCTION
The replacement of this part is a complementary
operation to the replacement of the cowl side pa-
nel (pillar lining) for a frontal impact.
It also requires the replacement of the cowl side
panel upper reinforcements (pillar lining), and
the use of the repair bench.
In the operation below there are only descriptions
of the joints specific to the part concerned.
Information concerning other parts will be dealt
with in the respective section.
COMPOSITION OF THE PART FROM THE PARTS
DEPARTMENT
Part assembled with :
- engine mounting height adjuster (right hand
side),
- engine support plate (right hand side),
- wheel arch ,
- shock absorber cup ,
- shock absorber cup height adjuster ,
- ABS mounting (right hand side),
- injection unit and impact sensor mounting
(left hand side).
JOINTS WITH :
Plenum chamber
Side member closure panel
Front side member
Front end lower cross member
PARTS CONCERNED (thickness in mm):
1Shock absorber cup height adjuster 1
2Engine mounting height adjuster 1.5
3Engine mounting reinforcement 1.5
4Shock absorber cup 2
5Plenum chamber 1
6Side member closure panel 1
7Front side member, front section 1.5
8Front side member, rear section 2.5
9Front wheel arch 1
10Front end lower cross member 1.5
11Injection unit and impact sensor
mounting (left hand side) 2
42-17

UPPER FRONT STRUCTURE
Plenum chamber
42G
PRB4214
INTRODUCTION
The replacement of this part is a complementary
operation to the replacement of :
- the wheel arch for a frontal impact,
- cowl side panel for a side impact.
This operation may be carried out partially (see
diagram and method below).
The Parts Department only provides chambers of
the (1) "air conditioning" type, as a result, the
closure panel must also be ordered (2).
In the following operation there are only descrip-
tions of the joints specific to the part concerned.
Information concerning other parts is dealt with
in the respective section.
COMPOSITION OF THE PART FROM THE PARTS
DEPARTMENT
1 Plenum chamber
Part assembled with :
- bonnet lock mounting,
- windscreen wiper motor mounting.
2 Partition closure panel.
JOINTS WITH :
Wheel arch
Injection unit and impact sensor mounting (left
hand side)
Bulkhead
Pillar lining (cowl side panel)
Windscreen aperture lower cross member
PARTS CONCERNED (thickness in mm) :
1Plenum chamber 1
2Shock absorber cup height adjuster 1
3Shock absorber cup 2
4Injection unit and impact sensor
mounting (left hand side) 2
5Bulkhead 1
6Cowl side panel (pillar lining) 1.5
7Windscreen wiper mounting 1.5
8Windscreen aperture lower cross
member 1.2
or
42-24

UPPER REAR STRUCTURE
Rear inner wheel arch
44E
PRB4417
INTRODUCTION
The replacement of this part is a complementary
operation to the wing panel with lining and rain
channel for a rear side impact.
In the operation described below there are only
descriptions of the joints specific to the part
concerned.
Information concerning other parts will be dealt
with in the respective section.
COMPOSITION OF THE PART FROM THE PARTS
DEPARTMENT
Part assembled with bumper reinforcement.
JOINTS WITH:
Rear floor
Rear side member
PARTS CONCERNED (thickness in mm):
1Rear inner wheel arch 1
2Bumper 1.5
3Bumper reinforcement 1.5
4Sill panel rear closure panel 1.5
5Rear shock absorber mounting
reinforcement 1.5
6Floor 0.8
44-30