1997 RENAULT KANGOO wheel

LOWER STRUCTURE
Rear floor, rear section (part section)
41M
PRB4133
INTRODUCTION
The replacement of this part is a complementary
operation to the replacement of:
1 - For a side impact :
- the sill panel reinforcement ,
- the rear inner wheel arch,
- the rear wing panel lining.
Replace part section along cut A (see diagram
and method below).
2 - For a rear impact
- the rear end panel,
- the rear side member, part section or
complete.
Replace part section along cut B (see diagram
and method below).
In the operation described below, there are only
descriptions of the joints specific to the part
concerned.
Information concerning the other parts will be
dealt with in the respective sections.
The repair bench must be used.
COMPOSITION OF THE PART FROM THE PARTS
DEPARTMENT
Part assembled with towing ring reinforcement.
JOINTS WITH:
Side floor
Upper shock absorber gusset
Sill panel closure panel
Rear axle assembly mounting unit
Shock absorber mounting upper reinforcement
Sill panel closure panel, rear section
Rear floor front cross member, front section
Rear side member
Wheel arch
Spring bumper mounting
Rear floor stiffener
Centre cross member
PARTS CONCERNED (thickness in mm):
1Rear floor, rear section 1
2Side floor 0.8
3Upper shock absorber gusset 1.5
4Sill panel closure panel 1.2
5Rear axle assembly mounting unit 1.2
6Shock absorber mounting
upper reinforcement 1.2
7Sill panel closure panel, rear section 1.5
8Rear floor front cross member 0.8
9Rear side member 1.5
10Wheel arch 1
11Spring bumper mounting 1.5
12Spring bumper mounting
reinforcement 1.5
13Rear floor stiffener 1
14Centre cross member 1.5
15Rear floor, front section 0.8
or
41-44

LOWER STRUCTURE
Complete rear side member
41T
PRB4140
INTRODUCTION
The replacement of this part is a complementary
operation to the replacement of the side panel
with lining and the inner wheel arch for a rear
side impact.
It requires the partial replacement of the rear
floor, rear section and the front cross member of
the rear floor .
In the operation described below, there are only
descriptions of the joints specific to the part
concerned.
Information concerning the other parts will be
dealt with in the respective sections.
The repair bench must be used.
COMPOSITION OF THE PART FROM THE PARTS
DEPARTMENT
Part assembled with:
- side member rear reinforcement,
- towing ring (left hand side),
- rear side member extension ,
- upper shock absorber gusset,
- rear axle assembly mounting unit,
- upper gusset of rear axle assembly mounting,
- side member reinforcement,
- sill panel closure panel, rear section.
JOINTS WITH:
Sill panel closure panel
Centre cross member
Rear floor stiffener
PARTS CONCERNED (thickness in mm):
1Rear side member 1.5
2Rear floor 1
3Centre cross member 1.5
4Sill panel closure panel 1.2
5Sill panel closure panel,
rear section 1.5
6Rear floor stiffener 1
7Rear shock absorber lower gusset 1.5
41-63

LOWER STRUCTURE
Centre cross member of rear floor
41U
PRB4141
INTRODUCTION
The replacement of this part is a complementary
operation to the replacement of the rear side
member for a rear side impact.
In the operation described below, there are only
descriptions of the joints specific to the part
concerned.
Information concerning the other parts will be
dealt with in the respective sections.
COMPOSITION OF THE PART FROM THE PARTS
DEPARTMENT
Part assembled with :
- brake limiter mounting,
- emergency spare wheel mounting bearing.
JOINTS WITH:
Seat mounting reinforcement
PARTS CONCERNED (thickness in mm):
1Rear floor centre cross member 1.5
2Rear side member 1.5
3Rear axle assembly mounting unit
closure panel 1
13237R1
CAA11538R4
A
1
2
CAS13024-1R5
B
1 2 3
41-67

LOWER STRUCTURE
Rear floor unit
41W
PRB4143
INTRODUCTION
The replacement of this part is a complementary
operation to the replacement of the rear end pa-
nel for a rear impact.
In the operation described below, there are only
descriptions of the joints specific to the part
concerned.
Information concerning the other parts will be
dealt with in the respective sections.
The repair bench must be used.
COMPOSITION OF THE PART FROM THE PARTS
DEPARTMENT
Part assembled with:
- rear end cross member,
- rear floor centre cross member,
- rear floor front cross member,
- rear floor,
- rear floor stiffener ,
- complete rear side members
JOINTS WITH:
Side floor
Tunnel
Sill panel closure panel
Side panel lining
Rear wheel arch
PARTS CONCERNED (thickness in mm):
1Side floor 0.8
2Tunnel 1.2
3Rear floor, rear section 1
4Sill panel closure panel 1.2
5Side panel lining 0.7
6Wheel arch 1
7Sill panel closure panel, rear section 1.5
8Rear floor front cross member 0.8
9Side panel 0.8
10Spring bumper mounting
reinforcement 1.5
11Spring bumper mounting 1.5
12Shock absorber mounting upper
reinforcement 1.2
41-71

UPPER FRONT STRUCTURE
Front wing
INTRODUCTION
The replacement of this part is a basic operation for a frontal impact.
It is a removable bodywork component.
COMPOSITION OF THE PART FROM THE PARTS DEPARTMENT
Part assembled with:
- mudguard skirt,
- bumper mounting support .
42A
13330R
Remove :
- the plastic cover at (A) on the wing side (see section 55),
- the wheel arch plastic mudguards (see section 55),
- the bumper and its mounting blade (see section 55),
- the indicator repeater,
- the front wing : 8 hexagonal-head bolts Ø 6 mm and a torx bolt Ø 6 mm.
42-1

UPPER FRONT STRUCTURE
Wheel arch, front section
42E
PRB4212
INTRODUCTION
The replacement of this part is an operation for a
frontal impact and is complementary to the repla-
cement of the cowl side panel (pillar lining).
It can be carried out partially from the right hand
side (see diagram and method below).
In the operation described below there are only
descriptions of the joints specific to the part
concerned.
Information concerning other parts will be dealt
with in the respective section.
COMPOSITION OF THE PART FROM THE PARTS
DEPARTMENT
1 - Part only (right hand side).
2 - Part only (left hand side).
JOINTS WITH :
Engine mounting height adjuster (right hand side)
Shock absorber cup height adjuster
Side member closure panel
Front end lower cross member (right hand side)
Cowl side panel (pillar lining)
PARTS CONCERNED (thickness in mm):
1Engine mounting 2
2Shock absorber cup height adjuster 2
3Side member closure panel 1
4Side member, front section 1.5
5Front wheel arch 1
6Front end lower cross member 1.5
7Cowl side panel (pillar lining) 1.5
or
42-12

UPPER FRONT STRUCTURE
Wheel arch, front section
42E
13009R
A
6
2
CAR11700R5
B
4 5
CAQ11697R5
C
4 5
CAI11550-2R5
3
42-13

UPPER FRONT STRUCTURE
Wheel arch, front section
42E
12903R2
or
CAS13028R8
D
CAS13028R1
E
5
54
3
5 1
42-14