1997 Oldsmobile Achieva Owner's Manuals

3. Press in the SET button at the end of the lever and
release it.
4. Take your foot off the accelerator pedal. Suppose
you set your cruise control at a desired speed
and then you apply the brake or clutch pedal. This, of
course, shuts off the cruise control. But you don’t need
to reset it. Once you’re going about
25 mph (40 km/h)
or more, you can move the cruise control switch from
ON to R/A (Resume/Accelerate) for about half a second.
You’ll
go right back up to your chosen speed and
stay there.

If you hold the switch at R/A longer than half a second,
the vehicle will keep going faster until
you release the
switch or apply the brake or clutch pedal.
You could be
startled and even
lose control. So unless you want to go
faster, don’t hold the switch at
R/A.
Increasing Speed While Using Cruise Control
There are two ways to go to a higher speed:
0
0
Use the accelerator pedal to get to the higher speed.
Push the SET button at the end of the lever, then
release the button and the accelerator pedal. You’ll
now cruise at the higher speed.
Move the cruise switch from
ON to R/A. Hold it
there until
you get up to the speed you want, and
then release the switch. (To increase your speed in
very small amounts, move the switch to
R/A for
less than half a second and then release
it. Each
time you
do this, your vehicle will go about 1 mph
(1.6 km/h) faster.)
The accelerate feature will only work after you turn
on
the cruise control by pushing the SET button.
Reducing Speed While Using Cruise Control
There are two ways to reduce your speed while using
cruise control:
Push in the button at the end of the lever until you
reach the lower speed you want, then release it.
To slow down in very small amounts, push the
button for less than half
a second. Each time you do
this, you’ll go
1 mph (1.6 km/h) slower.
Passing Another Vehicle While Using Cruise Control
Use the accelerator pedal to increase your speed. When
you take your foot off the pedal, your vehicle will slow
down to the cruise control speed you set earlier.
Using Cruise Control on Hills
How well your cruise control will work on hills depends
upon your speed, load and
the steepness of the hills.
When going up steep hills, you may have to step on the
2-42

accelerator pedal to maintain your speed. When going
downhill, you may have to brake or shift
to a lower gear
to keep your speed down.
Of course, applying the brake
or clutch pedal takes you out of cruise control. Many
drivers find this to be too much trouble and don’t use
cruise control on steep hills.
Ending Out of Cruise Control
There are two ways to turn off the cruise control:
0 Step lightly on the brake pedal or push the clutch
pedal, if you have a manual transaxle; OR
0 Move the cruise switch to OFF.
Erasing the Cruise Speed Memory
When you turn off the cruise control or the ignition,
your cruise control set speed memory is erased.
Exterior Lamps
Rotate the turn signal lever middle ring up one position
to turn on:
Parking Lamps
Sidemarker Lamps
Taillamps
License Plate Lamps
Instrument Panel Lights
2-43

Rotate the turn signal lever middle ring up two positions
to turn on:
Headlamps
Parking Lamps
Sidemarker Lamps
Taillamps
License Plate Lamps
0 Instrument Panel Lights
Rotate the switch to
OFF to turn all of the lamps off.
Lamps On Reminder
If you open the driver’s door and turn off the
ignition while leaving the lamps on, you will hear a
warning chime.
Daytime Running Lamps
Daytime Running Lamps (DRL) can make it easier for
others to see the front
of your vehicle during the day.
DRL can be helpful in many different driving
conditions, but they can be especially helpful
in the
short periods after dawn and before sunset.
The DRL system will make your high-beam headlamps
come on at a reduced brightness when:
The engine is running,
The headlamp switch is in the OFF position,
0 The light sensor detects daytime light,
0 The parking brake is released and
0 The shift lever is not in PARK (P) on an
automatic transaxle.
When the DRL system is on, the taillamps, sidemarker,
park lamps and instrument panel lights will not be
illuminated.
The DRL and the ALC systems will remain off any time
your automatic transaxle vehicle is
in PARK (P) and the
parking brake
is engaged.
The DRL and the ALC systems will remain off any time
your manual transaxle vehicle is in NEUTRAL
(N) and
the parking brake is engaged.
2-44

Automatic Light Control (ALC)
Your vehicle is equipped with an automatic light sensor
on top
of the instrument panel under the defroster grill,
so be sure it is not covered which will cause the
nighttime lights to be
on continuously.
When it is dark enough outside, your ALC will turn
on
your low-beam headlamps at the normal brightness
along with other lamps such as the taillamps,
sidemarker, park lamps and instrument panel lights.
There is a 20-second delay in the transition between
daytime and nighttime operation
of the DRL and the
ALC systems.
If the light sensor senses a reduction in
lighting that lasts longer than 20 seconds,
it will activate
the nighttime lamps.
If you are driving through a
parking garage, heavy overcast weather, a tunnel or
fueling your vehicle in a low light area, the ALC will
turn on your low-beam headlamps at a normal
brightness along with the taillamps, sidemarker, park
lamps and the instrument panel lights.
The radio lights
will be dimmer.
As with any vehicle, you should turn on the regular
headlamp system when you need it.
Fog Lamps (If Equipped)
The button for your fog
lamps is beside the
instrument panel
intensity control.
Push
the button to turn the fog lamps on. An indicator
light on the button will glow when the fog lamps
are on.
When using fog lamps, the parking lamps or low-beam
headlamps must be on.
The fog lamps will turn
off whenever the high-beam
headlamps are turned
on. When the high beams are
turned off, the fog lamps will come on again.

Interior Lamps
Instrument Panel Intensitv Control
You can brighten or dim the instrument panel cluster
lights by rotating the
INT LIGHTS switch.
Rotating the wheel to
MAX will turn on the
courtesy lamps.
Illuminated Entry System
When you lift the outside handle of either front door or
open either rear
door, the lamps inside your vehicle will
go on. These lamps will fade out after about 40 seconds,
or when the ignition
is turned on after all doors have
been closed. If the ignition was recently turned
off, the
lamps will fade out after four seconds. These lamps will
also
go on when you press the DOOR or UNLOCK
button
on the optional Remote Lock Control transmitter.
If the ignition has been off for less than two minutes,
the lamps inside your vehicle will stay on for about
15 seconds after your key is removed from the ignition
to provide an illuminated exit.

Front Reading Lamps (If Equipped) Front Map Lamps (If Equipped)
These lamps and the interior courtesy lamps will come on when
you open the doors.
To turn on a reading lamp when the doors
are closed,
press the button. Press it again to turn the lamp off. If
your vehicle has a
sunroof, it will have a rearview
mirror and lamps. The lamps go on when you open the
doors. When the doors are closed,
turn the lamps on and
off with the switch.

Rear Reading Lamps (If Equipped)
I
These overhead lamps and the interior courtesy lamps
will come on when you open the doors.
To turn on a reading lamp when the doors are closed,
push the button. Push it again to turn off the lamp.
nunk Lamp
The trunk lamp comes on when you open your trunk.
Battery Saver
Your Oldsmobile is equipped with a battery saver
feature designed to protect your vehicle’s battery.
When any interior lamp (trunk, reading, footwell or
glove box) is left
on when the ignition is turned off, the
battery saver system will automatically shut the lamp
off
after 20 minutes. This will avoid draining the battery.
To reactivate the interior lamps, either:
The ignition must be turned on,
The activated lamp switch must be turned off and
then
on or
A front door must be opened.
The battery saver feature will also be activated when
any door
of your vehicle is left open.
Also,
if your vehicle is left with the ignition turned off
for over
24 days, battery power to your clock and audio
system will be turned off to reduce battery drain. When
the ignition is turned on again, battery power will be
resupplied. However, under these conditions,
it will be
necessary to reset the clock and audio system settings.
2-48