1997 MITSUBISHI TRITON service

MPI ± Troubleshooting13A-36
INSPECTION PROCEDURE 17
The feeling of impact or vibration when decelerating.
Probable cause
Malfunction of the ISC system is suspected.
Malfunction of the ISC system
MUT-II Self-Diag code
Are diagnosis codes displayed?Ye sRefer to P.13A-10, INSPECTION CHART FOR DIAGNOSIS
CODES.
No
Check the ISC servo for operation sound. (Refer to P.13A-90.)NGCheck the ISC servo system.
(Refer to P.13A-45, INSPECTION PROCEDURE 31.)
OK
MUT-II Data list
14 Throttle position sensor (Refer to P.13A-57.)NGCheck the throttle position sensor system. (Refer to P.13A-13, IN-
SPECTION PROCEDURE FOR DIAGNOSIS CODE 14.)
OK
MUT-II Data list
26 Idle position switch (Refer to P.13A-57.)NGCheck the idle position switch system.
(Refer to P.13A-40, INSPECTION PROCEDURE 25.)
OK
Clean the throttle valve area. (Refer to P.13A-78.)
INSPECTION PROCEDURE 18
Poor acceleration
Probable cause
Defective ignition system, abnormal air-fuel ratio, poor compression pressure, etc.
are suspected.
Malfunction of the ignition system

Malfunction of air-fuel ratio control system

Malfunction of the fuel supply system

Poor compression pressure

Clogged exhaust system
MUT-II Self-Diag code
Are diagnosis codes displayed?Ye sRefer to P.13A-10, INSPECTION CHART FOR DIAGNOSIS
CODES.
No
Check the injectors for operation sound.NGCheck the injector system. (Refer to P.13A-19, INSPECTION PRO-
CEDURE FOR DIAGNOSIS CODE 41.)
OK
Check the ignition timing.
(Refer to GROUP 11 ± On-vehicle Service.)NGCheck that the distributor is installed properly.
OK
MUT-II: Check if hesitation, sag, stumble or poor acceleration occur.
(Refer to P.13A-51, INSPECTION PROCEDURE 40.)
OK
Check the fuel pressure. (Refer to P.13A-81.)
OK
Check the following items.

Check the ignition coil, spark plugs, spark plug cables. (Refer to GROUP 16 ± On-vehicle Service.)

Check the compression pressure. (Refer to GROUP 11 ± On-vehicle Service.)

Check the fuel filter or fuel line for clogging.

Broken air intake hose

Clogged air cleaner

MPI ± Troubleshooting13A-37
INSPECTION PROCEDURE 19
Surge
Probable cause
Defective ignition system, abnormal air-fuel ratio, etc. are suspected.
Malfunction of the ignition system

Malfunction of air-fuel ratio control system

Malfunction of the EGR control solenoid valve system
MUT-II Self-Diag code
Are diagnosis codes displayed?Ye sRefer to P.13A-10, INSPECTION CHART FOR DIAGNOSIS
CODES.
No
Check the injectors for operation sound.NGCheck the injector system. (Refer to P.13A-19, INSPECTION PRO-
CEDURE FOR DIAGNOSIS CODE 41.)
OK
Check the ignition timing.
(Refer to GROUP 11 ± On-vehicle Service.)NGCheck that the distributor is installed properly.
OK
MUT-II: Check if surge occurs.
(Refer to P.13-52, INSPECTION PROCEDURE 41.)
OK
Check the fuel pressure. (Refer to P.13A-81.)
OK
Check the following items.

Check the ignition coil, spark plugs, spark plug cables. (Refer to GROUP 16 ± On-vehicle Service.)

Check the EGR control system. (Refer to GROUP 17 ± Emission Control System.)
INSPECTION PROCEDURE 20
Knocking
Probable cause
In cases as the above, the cause is probably that the heat value of the spark plug
is inappropriate.
Inappropriate heat value of the spark plug
Check the following items.

Spark plugs

Check if foreign materials (water, alcohol, etc.) got into fuel.
INSPECTION PROCEDURE 21
Dieseling
Probable cause
Fuel leakage from injectors is suspected.
Fuel leakage from injectors
Check the injectors for fuel leakage.

MPI ± Troubleshooting13A-38
INSPECTION PROCEDURE 22
Too high CO and HC concentration when idling
Probable cause
Abnormal air-fuel ratio is suspected.
Malfunction of the air-fuel ratio control system

Deteriorated catalyst
Check trouble symptom.
No
Check the ignition timing.
(Refer to GROUP 11 ± On-vehicle Service.)NGCheck that the distributor is installed properly.
OK
MUT-II Data list
21 Engine coolant temperature sensor. (Refer to P.13A-57.)NGCheck the engine coolant temperature sensor system.
(Refer to P.13A-14, INSPECTION PROCEDURE FOR DIAGNOSIS
CODE 21.)
OK
MUT-II Data list
13 Intake air temperature sensor (Refer to P.13A-57.)NGCheck the intake air temperature sensor system. (Refer to P.13A-12,
INSPECTION PROCEDURE FOR DIAGNOSIS CODE 13.)
OK
MUT-II Data list
25 Barometric pressure sensor (Refer to P.13A-57.)NGCheck the barometric pressure sensor system. (Refer to P.13A-18,
INSPECTION PROCEDURE FOR DIAGNOSIS CODE 25.)
OK
MUT-II Data list
11 Oxygen sensor
OK:600 ± 1,000 mV when racing suddenly (Refer to P.13A-57.)NGCheck the oxygen sensor system. (Refer to P.13A-11, INSPECTION
PROCEDURE FOR DIAGNOSIS CODE 11.)
OK
MUT-II Data list
11 Oxygen sensor
OK:Repeat 0 ± 400 mV and 600 ± 1,000 mV alternately when
idling. (Refer to P.13A-57.)OK
NG
Check the fuel pressure. (Refer to P.13A-81.)
OK
NG
Check the following items.

Check the injectors for operation sound.

Check the injectors for fuel leakage.

Check the ignition coil, spark plugs, spark plug cables. (Refer to GROUP 16 ± On-vehicle Service.)

Check the compression pressure. (Refer to GROUP 11 ± On-vehicle Service.)

Check the positive crankcase ventilation system. (Refer to GROUP 17 ± Emission Control System.)

Check the purge control system. (Refer to GROUP 17 ± Emission Control System.)

Check the EGR control system. (Refer to GROUP 17 ± Emission Control System.)
Check the trouble symptom.
NG
Replace the catalytic converter.
Replace the oxygen sensor.
MUT-II Self-Diag code
Are diagnosis codes displayed?Ye sRefer to P.13A-10, INSPECTION CHART FOR DIAGNOSIS
CODES.

MPI ± Troubleshooting13A-42
INSPECTION PROCEDURE 27
Ignition switch-ST and inhibitor switch system
Probable cause

The ignition switch-ST inputs a HIGH signal to the engine-ECU while the engine
is cranking.
The engine-ECU controls fuel injection, etc. during starting based on this input.

The inhibitor switch inputs the condition of the select lever, i.e. whether it is in
P or N range or in some other range, to the engine-ECU.
The engine-ECU controls the idle speed control (ISC) servo based on this input.
Malfunction of ignition switch

Malfunction of inhibitor switch

Improper connector contact, open circuit or
short-circuited harness wire

Malfunction of the engine-ECU.
Check the following
connector. B-01
OK
Measure at the inhibitor switch connector B-01.

Disconnect the connector, and measure at the harness side.
1. Voltage between 6 and earth (Ignition switch: ON)
OK:System voltage
2. Continuity between 5 and earth
OK:Continuity
3. Voltage between 6 and earth

Ignition switch: START

Disconnect engine-ECU connector.
OK:System voltage1. NGCheck the following
connectors.
C-01, C-51, C-57NG
Repair
OK
Check trouble symptom. 2. NG
3. NG
Check the following
connector.
C-01, C-57, C-70NG
Repair
OK
Check trouble symptom.
NG
NG
Repair
Check harness wire be-
tween inhibitor switch and
ignition switch connector.
OK
Check the ignition switch.
(Refer to GROUP 54 ± Ignition Switch and Immobilizer system.)
OK
NG
Repair
OK
Check trouble symptom.
NG
Check harness wire be-
tween engine-ECU and
inhibitor switch connector.NG
Repair
OK
Replace the engine-ECU.
NG
ReplaceCheck the inhibitor switch.
(Refer to GROUP 23 ± On-vehicle Service.)
NG
Check the harness wire
between the engine-ECU
connector and inhibitor
switch connector.NG
Repair
OK
Replace the engine-ECU.
OK
Check trouble symptom.
NG
Check the harness wire between the inhibitor switch connector
and earth, and repair if necessary.
Check the following
connectors.
A-52X, C-19, C-57NG
Repair

MPI ± Troubleshooting13A-43
INSPECTION PROCEDURE 28
Power steering fluid pressure switch system
Probable cause
The presence or absence of power steering load is input to the engine-ECU.
The engine-ECU controls the idle speed control (ISC) servo based on this input.
Malfunction of power steering fluid pressure switch

Improper connector contact, open circuit or
short-circuited harness wire

Malfunction of the engine-ECU
Check the power steering fluid pressure switch.
(Refer to GROUP 37A ± On-vehicle Service.)NG
Replace
OK
Measure at the power steering fluid pressure switch connector
A-74.

Disconnect the connector, and measure at the harness side.

Voltage between 1 and earth (Ignition switch: ON)
OK:System voltageNGCheck the following
connector. C-50NG
Repair
OK
Check trouble symptom.
NG
Check harness wire be-
tween engine-ECU and
power steering fluid pres-
sure switch connector.NG
Repair
OK
Replace the engine-ECU.
OK
Check the following
connector. A-74NG
Repair
OK
Check trouble symptom.
NG
Replace the engine-ECU.
INSPECTION PROCEDURE 29
A/C switch and A/C relay system
Probable cause
When an A/C ON signal is input to the engine-ECU, the engine-ECU carries out
control of the idle speed control (ISC) servo, and also operates the A/C compressor
magnetic clutch.
Malfunction of A/C control system

Malfunction of A/C switch

Improper connector contact, open circuit or
short-circuited harness wire

Malfunction of the engine-ECU
Check the A/C compressor relay.
(Refer to GROUP 55 ± On-vehicle Service.)NG
Replace
OK
Measure at the engine-ECU connectors C-49, C-50.

Disconnect the connector, and measure at the harness side.


Voltage between 22 and earth, and 45 and earth
(Ignition switch: ON, A/C switch: ON)
OK:System voltage

Short circuit between 22 and earth
(Ignition switch: ON, A/C switch: ON)
OK:A/C compressor clutch turns on.


Voltage between 8 and earth, and 45 and earth
(Ignition switch: ON, A/C switch: ON)
OK:System voltage

Short circuit between 8 and earth
(Ignition switch: ON, A/C switch: ON)
OK:A/C compressor clutch turns on.NGCheck the A/C system. (Refer to GROUP 55 ± On-vehicle Service.)
OKCheck the following
connectors. C-49, C-50NG
Replace
OK
Check trouble symptom.
NG
Replace the engine-ECU.

MPI ± On-vehicle Service13A-83
14. Stop the engine and check change of fuel pressure gauge
reading. Normal if the reading does not drop within 2
minutes. If it does, observe the rate of drop and
troubleshoot and repair according to the table below.
SymptomProbable causeRemedy
Fuel pressure drops gradually after
engine is stopped
Leaky injectorReplace injector
engine is sto ed
Leaky fuel regulator valve seatReplace fuel pressure regulator
Fuel pressure drops sharply
immediately after engine is stoppedCheck valve in fuel pump is held openReplace fuel pump
15. Release residual pressure from the fuel pipe line. (Refer
to P.13A-84.)
16. Remove the fuel pressure gauge and special tool from
the delivery pipe.
Caution
Cover the hose connection with rags to prevent splash
of fuel that could be caused by some residual pressure
in the fuel pipe line.
17. Replace the O-ring at the end of the fuel high pressure
hose with a new one. Furthermore, apply engine oil to
the new O-ring before replacement.
18. Fit the fuel high pressure hose over the delivery pipe
and tighten the bolt to specified torque.
Tightening torque: 5 Nm
19. Check for fuel leaks.
(1) Apply the battery voltage to the fuel pump drive
terminal to drive the fuel pump.
(2) Under fuel pressure, check the fuel line for leaks.

MPI ± On-vehicle Service13A-91
PURGE CONTROL SOLENOID VALVE CHECK
13100560111
Refer to GROUP 17 ± Emission Control System.
EGR CONTROL SOLENOID VALVE CHECK
13100570107
Refer to GROUP 17 ± Emission Control System.

MPI ± Injector13A-93
REMOVAL SERVICE POINT
A
DELIVERY PIPE/INJECTOR REMOVAL
Remove the delivery pipe (with the injectors attached to it).
Caution
Care must be taken, when removing the delivery pipe,
not to drop the injector.
INSTALLATION SERVICE POINT

AINJECTOR/FUEL PRESSURE REGULATOR/
HIGH-PRESSURE FUEL HOSE INSTALLATION
(1) Apply a drop of new engine oil to the O-ring.
Caution
Be sure not to let engine oil in the delivery pipe.
(2) While turning the injector, high-pressure fuel hose and
fuel pressure regulator to the right and left, install the
delivery pipe, while being careful not to damage the O-ring.
After installing, check that the hose turns smoothly.
(3) If it does not turn smoothly, the O-ring may be trapped,
remove the fuel pressure regulator and then re-insert
it into the delivery pipe and check once again.
(4) Tighten the high-pressure fuel hose and fuel pressure
regulator to the specified torque.
Tightening torque:
9 Nm (Fuel pressure regulator)
5 Nm (High-pressure fuel hose)