ENGINE <4G6> ± Service Specifications11A-4
ItemsLimit Standard value
A/C compres-
sor drive belt
Tension NWhen checked355 ± 445±
sor drive belt
tensionWhen a used belt is installed355 ± 445±
When a new belt is installed530 ± 620±
Deflection
(Reference
When checked6.0 ± 7.0±
(Reference
value) mmWhen a used belt is installed6.0 ± 7.0±
When a new belt is installed4.5 ± 5.5±
Basic ignition timing5 BTDC+2±
Idle speed r/min750+100±
CO contents %0.5 or less±
HC contents ppm100 or less±
Compression pressure
(250±400 r/min) kPa
4G631,270min. 960
(250±400 r/min) kPa
4G641,320min. 1,000
Compression pressure difference of all cylinder kPa±max. 100
Intake manifold vacuum kPamin. 60±
Cylinder head bolt shank length mm±99.4
Auto-tensioner push rod movement mmWithin 1.0±
Timing belt tension torque Nm (Reference value)3.5±
Auto tensioner rod protrusion mm2.5 ± 3.0±
ENGINE ELECTRICAL ± Ignition System16-34
WAVEFORM OBSERVATION POINTS
Point A: The height, length and slope of the spark line show the following trends (Refer to abnormal
waveform examples, 1, 2, 3 and 4).
Spark linePlug gapCondition of
electrodeCompression
forceConcentration of
air mixtureIgnition timingSpark plug
cable
LengthLongSmallNormalLowRichAdvancedLeak
ShortLargeLarge wearHighLeanRetardedHigh
resistance
HeightHighLargeLarge wearHighLeanRetardedHigh
resistance
LowSmallNormalLowRichAdvancedLeak
SlopeLargePlug is fouled±±±±
Point B: Number of vibration in reduction vibration section (Refer to abnormal waveform example 5)
Number of vibrationsCoil and condenser
Three or moreNormal
Except aboveAbnormal
Point C: Number of vibrations at beginning of dwell section (Refer to abnormal waveform example 5)
Number of vibrationsCoil
5 ± 6 or higherNormal
Except aboveAbnormal
Point D: Ignition voltage height (distribution per each cylinder) shows the following trends.
Ignition
voltagePlug gapCondition of
electrodeCompression
forceConcentration of
air mixtureIgnition timingSpark plug cable
HighLargeLarge wearHighLeanRetardedHigh resistance
LowSmallNormalLowRichAdvancedLeak
ENGINE ELECTRICAL ± Ignition System16-38
WAVEFORM OBSERVATION POINTS
Point A: The height, length and slope of the spark line (refer to abnormal waveform examples 1, 2,
3 and 4) show the following trends.
Spark linePlug gapCondition of
electrodeCompression
forceConcentration of
air mixtureIgnition timingHigh tension
cable
LengthLongSmallNormalLowRichAdvancedLeak
ShortLargeLarge wearHighLeanRetardedHigh
resistance
HeightHighLargeLarge wearHighLeanRetardedHigh
resistance
LowSmallNormalLowRichAdvancedLeak
SlopeLargePlug is fouled±±±±
Point B: Number of vibration in reduction vibration section
(Refer to abnormal waveform example 5)
Number of vibrationsCoil, condenser
3 or higherNormal
Except aboveAbnormal
Point C: Height of Zener voltage
Height of Zener voltageProbable cause
HighProblem in Zener diode
LowAbnormal resistance in
primary coil circuit
FRONT AXLE ± General Information26-2
GENERAL INFORMATION26100010111
2WD
The front hub assembly which uses a double taper
roller bearing is mounted on the knuckle spindle.For vehicles with ABS, a rotor for detecting the
wheel speed is press-fitted into the front hub.
4WD
The front axle consists of the hub assembly, drive
shaft, inner shaft, front differential, freewheel clutch
assembly and actuator. The features are:
The wheel bearing uses a double taper roller
bearing. For vehicles with ABS, a rotor for
detecting the wheel speed is bolted to the brake
disc.
Drive shafts of almost identical length reduce
torque steer. In addition, a D.O.J.-B.J.-type
constant velocity ball joint has high power
transmission efficiency and reduces vibration
and noise.A vacuum-type freewheel clutch has been
adopted in the freewheel mechanism. Its
solenoid valve and actuator switch powertrain
between 2WD and 4WD.
There are two types of differential gear. The
difference between them is gear ratio.
2WD
ItemSpecifications
Wheel bearingTypeDouble taper roller bearing
Inner bearing (O.D. x I.D.) mm65.1 x 34.9
Outer bearing (O.D. x I.D.) mm50.0 x 21.4
4WD
ItemSpecifications
Wheel bearingTypeDouble taper roller bearing
Inner bearing (O.D. x I.D.) mm73 x 45
Outer bearing (O.D. x I.D.) mm73 x 45
Drive shaftJoint typeOuter: B.J.
Inner: D.O.J.
Shaft length (joint to joint) mmRight: 318
Left: 291
Inner shaftO.D. x length mm31.5 x 304.2
Bearing (O.D. x I.D.) mm62 x 35
FRONT AXLE ± Service Specifications/Lubricants26-4
SERVICE SPECIFICATIONS26100030131
ItemStandard valueLimit
Front axle total backlash mm±11
Drive shaft axial play mm0.4 ± 0.7±
Solenoid valve resistance W36 ± 46±
Hub rotary sliding resistance N7 ± 26±
(Hub rotation starting torque) Nm0.5 ± 1.8±
Amount of movement of far the wheel bearing in an axial
direction mm0.05 or less±
Setting of D.O.J. boot length mm80 + 3±
Clutch gear play (bearing axial play) mm0.05 ± 0.30±
Drive gear backlash mm0.11 ± 0.16±
Differential gear backlash mm0 ± 0.076±
Drive pinion rotation torque NmWithout oil sealWhen replacing (with anti-rust agent)
0.3 ± 0.5±
When replacing or reusing (with gear oil
applied) 0.15 ± 0.25±
With oil sealWhen replacing (with anti-rust agent)
0.5 ± 0.7±
When replacing or reusing (with gear oil
applied) 0.3 ± 0.4±
Drive gear runout mm±0.05
Differential gear backlash mm±0.2
LUBRICANTS26100040141
ItemsSpecified lubricantsQuantity
Front differential gear oilHypoid gear oil API classification
GL-5 or higher SAE viscosity No. 90,
80W0.9
D.O.J. boot greaseRepair kit grease100 g
REAR AXLE ± General Information27-2
GENERAL INFORMATION27100010118
The rear axle is a banjo-type semi-floating type.
The axle shaft bearings are: *Single taper
bearings for vehicles without ABS or rear
differential lock. *Double-taper bearings for
vehicles with ABS or rear differential lock. ABS
rotor is press-fitted to the axle shaft retainer
ring.Differential gear has 4 different types. A
torque-responsive mechanical-type limited slip
differential has a high performance against
driving on unstable surfaces such as muddy
roads.
Driveability on sand or muddy road has been
improved, and rear differential lock, which is
useful for emergency , has been used.
REAR AXLE
ItemVehicles without rear differential lockVehicles with rear differential lock
Axle housing typeBanjo typeBanjo type
Axle
shaft
Support methodSemi-floating typeSemi-floating type
shaft
Shaft O.D. (Bearing part x
Centre x Length) mm40.0 x 34.5 x 744.540.0 x 34.5 x 723.5 (LH)
40.0 x 34.5 x 761.0 (RH)
Bearing typeSingle taper (double taper)*Double taper
Bearing (O.D. x I.D.) mm80.0 x 40.080.0 x 40.0
NOTE
*: Vehicles with ABS.
DIFFERENTIAL
<2WD>
Item4G634D56
Drive gear typeHypoid gearHypoid gear
Reduction ratio4.6364.222
Limited slip differential typeTorque sensitivity type mechanicalTorque sensitivity type mechanical
Differential gear type
(type x quantity)
Side gearStraight bevel gear x 2Straight bevel gear x 2
(ty e x quantity)
Pinion gearStraight bevel gear x 2 [Straight bevel
gear x 4]Straight bevel gear x 2 [Straight bevel
gear x 4]
Number of teethSide gear5138
Drive pinion119
Side gear1414
Pinion gear1010
Bearing (O.D. x I.D.)
mm
Side80.0 x 45.280.0 x 45.2
mm
Front68.3 x 30.268.3 x 30.2
Rear76.2 x 36.576.2 x 36.5
NOTE
[ ]: Vehicles with limited slip differential
35A-2
BASIC BRAKE
SYSTEM
CONTENTS35109000197
GENERAL INFORMATION 3. . . . . . . . . . . . . . . . . .
SERVICE SPECIFICATIONS 5. . . . . . . . . . . . . . . . .
LUBRICANTS 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SEALANTS 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SPECIAL TOOLS 6. . . . . . . . . . . . . . . . . . . . . . . . . . .
TROUBLESHOOTING 7. . . . . . . . . . . . . . . . . . . . . . .
ON-VEHICLE SERVICE 10. . . . . . . . . . . . . . . . . . . .
Brake Pedal Check and Adjustment 10. . . . . . . . . .
Stop Lamp Switch Check 11. . . . . . . . . . . . . . . . . . . . .
Brake Booster Operating Test 11. . . . . . . . . . . . . . . . .
Check Valve Operation Check 12. . . . . . . . . . . . . . .
Brake Booster Vacuum Switch Check
Bleeding 12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Brake Fluid Level Sensor Check 13. . . . . . . . . . . . . Load Sensing Spring Length Check and
Adjustment 13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Load Sensing Proportioning Valve Function
Test 14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Disc Brake Pad Check and Replacement 15. . . . .
Front Disc Brake Rotor Check 16. . . . . . . . . . . . . . .
Brake Lining Thickness Check 17. . . . . . . . . . . . . . .
Brake Drum Inside Diameter Check 18. . . . . . . . . .
Brake Lining and Brake Drum Connection
Check 18. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . BRAKE PEDAL 19. . . . . . . . . . . . . . . . . . . . . . . . . . .
MASTER CYLINDER AND BRAKE
BOOSTER 20. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LOAD SENSING PROPORTIONING
VA LV E 2 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FRONT DISC BRAKE 24. . . . . . . . . . . . . . . . . . . . .
REAR DRUM BRAKE 30. . . . . . . . . . . . . . . . . . . . .
BASIC BRAKE SYSTEM ± Service Specifications35A-5
SERVICE SPECIFICATIONS35100030119
ItemsStandard valueLimit
Brake pedal height mm176 ± 181±
Brake pedal free play mm3 ± 8±
Brake pedal to floor board clearance mm95 or more±
Load sensing proportioning
valve outputpressure kPa
2WDWhen load sensing
spring length is 190
3,625 (5,884)±
valve out ut ressure kPa
(Input pressure kPa)
s ring length is 190
mm (when unladen)5,390 (17,652)±
When load sensing
spring length is 215
mm (when laden)14,393 (17,652)±
4WDWhen load sensing
spring length is 190
4,309 (5,884)±
s ring length is 190
mm (when unladen)6,074 (17,652)±
When load sensing
spring length is 215
mm (when laden)16,310 (17,652)±
Load sensing spring length mm189 ± 193±
Booster push rod to master
cylinder piston clearance mmSingle brake boosterPetrol-powered ve-
hicles0.65 ± 1.05±
Diesel-powered ve-
hicles1.00 ± 1.40±
Tandem brake boosterVehicle which brake
booster of power
cylinder is 180 mm
and 205 mm in
effective diameter0.90 ± 1.30±
Vehicle which brake
booster of power
cylinder is 205 mm
and 230 mm in
effective diameter0.70 ± 1.10±
Front disc brake pad thickness mm102.0
Front brake disc thickness mm2422.4
Front brake disc run-out mm2WD±0.08
4WD±0,06
Front disc brake drag force (tangential force of wheel mounting bolts) N69 or less±
Rear drum brake lining thickness mm4.71.0
Rear drum inside diameter mm2WD254.0256.0
4WD270.0272.0
Front hub end play mm0.05±