1997 MITSUBISHI TRITON length

35B-2
Bleeding 23. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Brake Fluid Level Sensor Check
Refer to GROUP 35A . . . . . . . . . . . . . . . . . . . . . . . . . .
Load Sensing Spring Length Check and
Adjustment Refer to GROUP 35A. . . . . . . . . . . . . . .
Load Sensing Proportioning Valve Function
Test Refer to GROUP 35A. . . . . . . . . . . . . . . . . . . . .
Disc Brake Pad Check and Replacement 23. . . . .
Front Disc Brake Rotor Check
Refer to GROUP 35A . . . . . . . . . . . . . . . . . . . . . . . . . .
Brake Lining Thickness Check
Refer to GROUP 35A . . . . . . . . . . . . . . . . . . . . . . . . . .
Brake Drum Inside Diameter Check
Refer to GROUP 35A . . . . . . . . . . . . . . . . . . . . . . . . . .
Brake Lining and Brake Drum Connection Check
Refer to GROUP 35A . . . . . . . . . . . . . . . . . . . . . . . . . .
Wheel Speed Sensor Output Voltage Check
24 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hydraulic Unit Check 26. . . . . . . . . . . . . . . . . . . . . . . .
Solenoid Valve Check 27. . . . . . . . . . . . . . . . . . . . . . .
Motor Operation Check 27. . . . . . . . . . . . . . . . . . . . . . Motor Relay and Valve Relay Continuity
Check 28. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Remedy for a Flat Battery 28. . . . . . . . . . . . . . . . . . .
BRAKE PEDAL Refer to GROUP 35A. . . . . . . .
MASTER CYLINDER AND BRAKE
BOOSTER 29. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LOAD SENSING PROPORTIONING VALVE
Refer to GROUP 35A . . . . . . . . . . . . . . . . . . . . . . . .
FRONT DISC BRAKE 32. . . . . . . . . . . . . . . . . . . . .
REAR DRUM BRAKE
Refer to GROUP 35A . . . . . . . . . . . . . . . . . . . . . . . .
HYDRAULIC UNIT 37. . . . . . . . . . . . . . . . . . . . . . . . .
WHEEL SPEED SENSOR 39. . . . . . . . . . . . . . . . . .
ABS-ECU 41. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

35C-2
For the items below, refer to GROUP
35A.
SEALANTS
ON-VEHICLE SERVICE
Brake Pedal Check and Adjustment
Stop Lamp Switch Inspection
Brake Booster Operating Test
Check Valve Operation Check
Brake Booster Vacuum Switch Check
Load Sensing Spring Length Check and
Adjustment
Load Sensing Proportioning Valve Function
Test
Front Disc Brake Rotor Check
Brake Lining Thickness Check
Brake Drum Inside Diameter Check
Brake Lining and Brake Drum Connection
Check
BRAKE PEDAL
LOAD SENSING PROPORTIONING VALVE
REAR DRUM BRAKE
For the items below, refer to GROUP
35B.
ON-VEHICLE SERVICE
Bleeding
Disc Brake Pad Check and Replacement
Wheel Speed Sensor Output Voltage Check
Hydraulic Unit Check
Solenoid Valve Check
Motor Operation Check
Motor Relay and Valve Relay Continuity Check
Remedy for a Flat Battery
MASTER CYLINDER AND BRAKE
BOOSTER
HYDRAULIC UNIT
ABS-ECU

CHASSIS ELECTRICAL ± Radio and Tape Player54-73
B-8 Insufficient memory (preset stations are erased).
Is dedicated fuse No. 5 blown or is the circuit open?Ye sReplace fuse or repair harness.
No
Disconnect and check the connector at the rear of the radio.
Is the memory backup (battery) power being supplied?NoRepair harness.
Ye s
Repair or replace radio.
C. TAPE PLAYER
C-1 Cassette tape will not be inserted.
Are there any foreign objects in the tape player?Ye sRemove the object(s)*1
No*1
Attempting to force a foreign object (e.g., a coin or clip, etc.) out
of the tape player may damage the mechanism. The player should
be taken to a service dealer for repair.
Does the tape player work if another tape is inserted?Ye sReplace tape*2
No
Repair or replace tape player.
*2
Ensure that the tape label is not loose, that the tape itself is not
deformed and that the tape is tightly wound. Also, tape of C-120
or greater length often get caught in the mechanism and should
not be used.
C-2 No sound (even after a tape has been inserted).
Is dedicated fuse No. 4 blown or is the circuit open?Ye sReplace fuse or repair harness.
No
Is connector at rear of radio connected tightly?NoConnect connector firmly.
Ye s
Disconnect connector at rear of radio. Is ACC power being supplied
to the radio?Ye sRepair or replace tape player.
No
Repair harness.

CHASSIS ELECTRICAL ± Radio and Tape Player54-74
C-3 No sound from one speaker.
Clean the tape player head and check again.Ye sOK
No
Replace the tape player and check again.Ye sRepair or replace tape player.
No
Remove the connector on the back of the radio and check
the speaker harness for conductance.Ye sIt conducts electricity but is
shorted out.Repair harness.
No
Check the speaker for conductance.Ye sRepair harness.
No
Repair or replace speaker.
C-4 Sound quality is poor, or sound is weak.
Does the player play properly when another tape* is inserted?Ye sOK
No
*:

Ensure that the tape label is not loose, that the tape
itself is not deformed and that the tape is tightly wound.

Tapes of C-120 or greater length often get caught in
the mechanism and should not be used.
Does the player play properly when the tape player head is cleaned?Ye sOK
No
Is proper operation obtained when the tape player is replaced?Ye sRepair or replace tape player.
No
Repair or replace speaker.
C-5 Cassette tape will not be ejected.
The problems covered here are all the result of
the use of a bad tape (deformed or not properly
tightened) or of a malfunction of the tape player
itself. Malfunctions involving the tape becoming
caught in the mechanism and ruining the case arealso possible, and attempting to force the tape out
of the player can cause damage to the mechanism.
The player should be taken to a service dealer
for repair.

CHASSIS ELECTRICAL ± Radio and Tape Player54-76
C-8 Tape gets caught in mechanism*1.
*1
When the tape is caught in the mechanism, the case may
not eject. When this occurs, do not try to force the tape
out as this may damage the tape player mechanism. Take
the cassette to a service dealer for repair.
Does the player play OK if the tape*2 is changed?Ye sTape used is bad.
No
*2
Ensure that the tape label is not loose, that the tape itself
is not deformed and that the tape is tightly wound. Also,
tapes of C-120 or greater length often get caught in the
mechanism and should not be used.
Repair or replace tape player.