1997 Lexus GS300 reset

AIR CONDITIONING AND AUDIO
11 2(a) Listening to the radio
1. Push the
(A/M) or (F/M 1/2) button to
turn the radio on and select either an AM or FM broadcast.
ªAM,º ªFM1º or ªFM2º will appear on the display.
The radio can also be turned on by pushing the ªPWR.VOLº
knob if the radio was being used when the system was
turned off.
2. Tune the ªPWR.VOLº knob to adjust the volume.
3. Tune in the desired station. (See ª(b) Selecting a
station.º)
The radio will change automatically to stereo reception when
an FM stereo broadcast is being received. At the same time
ªSTº will appear on the display. When the receiving signal
gets weak, the channel separation will automatically be
reduced for lowest noise. If the signal becomes extremely
weak, the radio will switch over to monaural reception.
4. Adjust the tone and sound balance. (See ª(d) Adjusting
the toneº and ª(e) Adjusting the sound balance.º)
5. To turn the radio off, push the ªPWR.VOLº knob.(b) Selecting a station
Tune in the desired station using one of the following
methods. The frequency will appear on the display.
Preset tuning: Use for tuning±in to a desired preset station.
Push the station selector button to which the desired station
has been preset. The radio will tune in to the station and the
button number will appear on the display. See ª(c) Presetting
a station.º)
Seek tuning: Use for automatic station search and stop.
Push the
(SEEK) button and hold it until a beep is heard.
The radio will begin seeking up or down for a station of the
nearest frequency and will stop on reception. Each time you
push the button, stations will be searched out one after
another.
Scan tuning: Use for scanning preset stations or
station±to±station scanning.
Push the
(SCAN) button for less than 2 seconds. With
ªP. SCANº blinking on the display, the radio will automatically
seek out a preset station of a higher channel number in the
AM/FM mode. If there is a preset station on the channel,
then the tuning is held for 5 seconds. If there is no station
on the channel, then the tuning is only held for 1 second. If
the
(SCAN) button is pushed while listening to a preset
station channel, then the scan proceeds to the next highest
channel, proceeding in turn through the 6 channels of FM1
and then the 6 channels of FM2, then repeating the process.
To continue listening to the channel of your choice, simply
push the
(SCAN) button once again.

AIR CONDITIONING AND AUDIO
11 3 Push the
(SCAN) button for longer than 2 seconds.
With ªSCANº on the display, the radio will automatically seek
out a station of higher frequency, hold it for 5 seconds and
scan to the next. To continue listening to the broadcast of
your choice, simply push the
(SCAN) button once
again.
Manual tuning: Push the
(TUNE) button briefly. Each
time you push the button, the radio will step up or down to
another frequency.
(c) Presetting a station
1. Tune in the desired station. (See ª(b) Selecting a
station.º)
2. Push one of the station selector buttons and hold it until
a beep is heard. This sets the station to the button and the
button number will appear on the display.
Each button can store one AM station and two FM stations.
To change the preset station to a different one, follow the
same procedure.
The preset station will be cancelled when the power source
is cut off (battery disconnected, blown fuse, etc.).
(d) Adjusting the tone
To adjust the low±pitched tone, push the ªBASSº knob (if
depressed) and turn it.
To adjust the middle±pitched tone, push the ªMIDº knob (if
depressed) and turn it.
To adjust the high±pitched tone, push the ªTREBLEº knob (if
depressed) and turn it.(e) Adjusting the sounds balance
To balance the sound between the right and left speakers,
push the ªBALANCEº knob (if depressed) and turn it.
To balance the sound between the front and rear speakers,
push the ªFADERº knob (if depressed) and turn it.
Radio operating tips
The antenna automatically extends when the radio and
ignition are turned on and retracts when either is turned off.
CAUTION!
Before extending the antenna, confirm that no one
is close enough to get injured.
NOTICE
To prevent damage to the antenna, make sure it is
retracted before running your vehicle through an
automatic car wash.

AIR CONDITIONING AND AUDIO
122(c) Selecting a compact disc
Push the
(DISC) button on the left side to select the
disc number.
Push the
(DISC) button on the left side and hold it
until the desired disc number appears on the display. As you
release the button, the player will start playing the selected
disc from the beginning.
(d) Selecting a program
Automatic program selection: Use for direct access to a
desired program.
Push the
(TRACK) button on either side and hold it
until the desired program track number appears on the
display. As you release the button, the player will start
playing the selected program from the beginning.
Manual program selection:
Push the
(FF) button on the right side and hold it to
fast forward the disc. Releasing the button starts the play
from that position.
Disc scan selection: Use for disc±to±disc scanning.
Push the
(SCAN) button. With ªSCANº on the display,
the program at the beginning of each disc will be played for
10 seconds. To continue listening to the program of your
choice, push the
(CD) button or the (SCAN) button.(e) Other compact disc player functions
ªRPTº button: Use for automatic repeat of the program
currently being listened to.
Push the
(RPT) button on the left side while the
program is being played. As this is done, ªRPTº will appear
on the display. When the program is finished, the disc will
automatically go back to the beginning of the program and
the program will be played again. To cancel it, push the
button once again.
ªRANDOMº button: USe for automatic program selection
and play by the system.
When the
(RANDOM) button is pushed on the right
side, ªRNDº appears on the display and the system selects
a program in the disc which is set and plays it. To cancel it,
push the button once again.
When a program is skipped or the system is inoperative,
push the
(CD) button to reset.
ªCD CMPº button (Nakamichi±made only): Use for
listening to music in noisy situations.
Push the
(CD CMP) button and hold it until a beep is
heard. ªCMPº appears on the display. Small sounds are
emphasized and large sounds muted slightly so that every
sound can be heard clearly.
This function works only in the ªCDº mode. To cancel it, push
the button once again and hold it until a beep is heard.

AIR CONDITIONING AND AUDIO
125
Anti±theft system (Nakamichi±made only)
To deter theft of your radio, the system is designed so
that the radio unit becomes inoperable if it is stolen
from the vehicle.
The system is not preset at the factory. You must input a
three±digit identification number decided by you.
NOTICE
If you pushed any wrong buttons on the anti±theft
system, the following messages will appear on the
display.
ªErrº ± You have pushed wrong buttons.
ª1±9º ± Indicates the number of errors you
have made. You may make up to nine
errors, but no more!
ªHELPº ± The number of errors you can make
was exceeded. The audio system is
completely inoperable. Contact your
Lexus dealer.
(a) Setting the anti±theft system
1. Make sure the radio unit is turned off with the ignition
switch in ªACC.º
2. While holding the left side of the (1) and right side
of the
(6) buttons in, push and hold the ªPWR.VOLº
knob in until ªSECº appears on the display.
3. Press the left side of the (1) button while holding
the upper side of the
(TUNE SEEK) button in. ª±±±º and
the tape operation indicator will appear on the display.

AIR CONDITIONING AND AUDIO
128
NOTICE
A tenth error will activate the anti±theft system and
ªHELPº will appear on the display. The audio
system will be completely inoperable. At this time,
the indicator light also comes on. If this occurs,
contact your Lexus dealer.
At the time of resale of your vehicle, cancel the system for
the new owner.(c) If the anti±theft system is activated
The audio system made inoperable by the activated
anti±theft system will be operable if you give it the correct
identification number.
1. Follow steps 3 and 4 described in ª(a) Setting the
anti±theft system.º
2. With your identification number appearing on the
display, press the
(SCAN) button and hold it in until
ªSECº appears on the display. ªSECº will go off to indicate
that the system is reset and the audio system is operable.
If invalid buttons have been used, ªErrº will appear on the
display before ªSECº appears. Try again from the beginning.
See ª(b) Cancelling the anti±theft systemº for notes on the
number displayed with ªErr.º