8Loosen the bolts or nuts and move the boot
lid into correct alignment. Move it only a little
at a time. Tighten the hinge bolts or nuts and
carefully lower the boot lid to check the
alignment.
9If necessary after refitting, the entire boot
lid striker assembly can be adjusted up and
down as well as from side to side on the boot
lid so the lid closes securely and is flush with
the rear quarter panels. To do this, scribe a
line around the boot lid striker assembly to
provide a reference point. Then loosen the
bolts and reposition the striker as necessary
(see illustration). Following adjustment,
retighten the mounting bolts.
10Adjust the bump stops on the boot lid so
the boot lid is flush with the rear wings when
closed (see illustration).
11The boot lid latch assembly, as well as the
hinges, should be periodically lubricated with
white lithium-base grease to prevent sticking
and wear.
17 Boot lid latch and lock
cylinder- removal and
refitting
1
Boot lid latch
1Open the boot and scribe a line around the
boot lid latch assembly for a reference point
to help aid the refitting procedure.2The boot lid latch is retained by three
Phillips-head screws (see illustration). For
adjustment procedures, see Section 16.
3Disengage the lock rod from the latch.
4Disconnect all electrical connectors and
remove the latch.
5Refitting is the reverse of removal.
Boot lock cylinder
6Remove the plastic clips securing the boot
light finish panel (see illustration).
7Looking upward through the boot lid
access hole, remove the lock rod and lock
cylinder retaining bolts (see illustration).
8Disconnect all electrical connections and
remove the lock cylinder assembly.
9Refitting is the reverse of removal.
18 Door trim panel-
removal and refitting
2
1Disconnect the negative cable from the
battery.
Caution: If the stereo in your vehicle is
equipped with an anti-theft system, make
sure you have the correct activation code
before disconnecting the battery
2On front door trim panels, remove the
retaining screw located under the air duct
door seal (see illustration).
3Remove the inside handle trim bezel (see
illustrations).
Bodywork and fittings 11•7
11
17.6 Detach the clips securing the boot
lamp finish panel17.7 Disengage the lock rod (A), then
remove the lock cylinder retaining bolts (B)
18.2 Lift the air duct-to-body seal to
access the trim panel retaining screw
(arrowed)18.3b . . . then detach the inside handle
retaining screw and bezel18.3a Remove the trim cover . . .
3261 Jaguar XJ6 16.9 Loosen the bolts and move the
striker assembly as necessary to adjust
the boot lid flush with the quarter panels
in the closed position
17.2 Remove the retaining screws
(arrowed), then unclip the lock rod and
disconnect any electrical connections16.10 Turn the bump stops in or out so the
boot lid is flush with the rear wings when
in the closed position
4Detach the wood finishing panel (see
illustration).
5Unscrew the inside lock knob, then remove
the remaining screws securing the upper half
of the door trim panel and detach it from the
vehicle (see illustration).
6Detach the screw from the top edge of the
lower door trim panel (see illustration).
7Pry out the courtesy lamp lens, then detach
the retaining screw from inside the lamp
housing (see illustrations).
8Remove the armrest trim cover, then
detach the retaining screws from behind the
cover (see illustrations).
9Insert a wide putty knife, a screwdriver or a
special trim panel removal tool between thetrim panel and the head of the retaining clips
to disengage the retaining clips along the outer
edges of the door panel (see illustration). Pry
only at the clip locations or the panel could be
damaged.
10Once all of the clips are disengaged,
detach the trim panel, unplug any electrical
connectors and remove the trim panel from
the door by gently pulling it up and out.
11For access to the inner door, peel back
the watershield, taking care not to tear it. To
refit the trim panel, first press the watershield
back into place. If necessary, add more
sealant to hold it in place.
12Refitting is the reverse of removal.19 Door- removal,
refitting and adjustment
3
Note:The door is heavy and somewhat
awkward to remove and refit - at least two
people should perform this procedure.
Removal and refitting
1Raise the window completely in the door,
then disconnect the battery negative cable.
Caution: If the stereo in your vehicle is
equipped with an anti-theft system, make
sure you have the correct activation code
before disconnecting the battery.
11•8 Bodywork and fittings
18.6 Detach the screws along the top
edge of the lower trim panel18.7a Prise out the courtesy lamp lens18.7b Remove the retaining screw from
inside the lamp housing
18.8a Push up on the bottom to detach the
armrest/pull handle trim cover18.8b Remove the screws behind the
armrest/pull handle trim cover18.9 Disengage the retaining clips along
the outer edge of the door trim panel
3261 Jaguar XJ6 18.4 Gently prise out the clips securing the wood finish panel
18.5 Detach the screws located behind the wood finisher panel,
then remove the upper portion of the door trim panel
2Open the door all the way and support it on
jacks or blocks covered with rags to prevent
damaging the paint.
3Remove the door trim panel and water
deflector as described in Section 18.
4Unplug all electrical connections, ground
wires and harness retaining clips from the
door. Note:It is a good idea to label all
connections to aid the reassembly process.
5From the door side, detach the rubber
conduit between the body and the door, then
carefully pull the wiring harness through the
conduit hole and remove it from the door.
6Mark around the door hinges with a pen or
a scribe to ease alignment during reassembly.
7On front doors, work through the door
access hole to remove the hinge-to-door
nuts. On rear doors the hinge-to-body bolts
are more accessible and can be removed by
simply opening the front door and removing
the bolts (see illustrations).
8Have an assistant hold the door, remove
the bolts or nuts and lift the door off.
9Refitting is the reverse of removal.
Adjustment
10Having proper door to body alignment is a
critical part of a well functioning doorassembly. First check the door hinge pins for
excessive play. Note: If the door can be lifted
(1/16-inch or more) without the car body
moving, the hinges should be replaced.
11Door-to-body alignment adjustments are
made by loosening the hinge-to-body or hinge-
to-door bolts and moving the door. Proper
body alignment is achieved when the top of
doors are parallel with the roof section, the
front door is flush with the wing, the rear door is
flush with the rear quarter panel and the
bottom of the doors are aligned with the lower
rocker panel. If these goals can’t be reached by
adjusting the hinge-to-body or hinge-to-door
bolts, body alignment shims may have to be
purchased and inserted behind the hinges to
achieve correct alignment.
12To adjust the door closed position, scribe
a line or mark around the striker plate to
provide a reference point. Check that the door
latch is contacting the centre of the latch
striker. If not, adjust the up-and-down
position first.
13Finally, adjust the latch striker position, so
the door skin is flush with the rear door (front)
or rear quarter panel (rear) and provides
positive engagement with the latch
mechanism (see illustration).
20 Door latch, lock cylinder and
handles- removal and refitting
2
Door latch
1Raise the window, then remove the door
trim panel and watershield as described in
Section 18.
2Working through the large access hole,
disengage the outside door handle-to-latch
rod and the inside handle-to-latch cable (see
illustration).
3All door locking rods are attached by plastic
clips. The plastic clips can be removed by
unsnapping the portion engaging the
connecting rod and then by pulling the rod out
of its locating hole.
4Remove the screws securing the latch to
the door (see illustration), then remove the
latch assembly from the door.
5Refitting is the reverse of removal.
Outside handle
and door lock cylinder
6To remove the outside handle and lock
cylinder assembly, raise the window then
Bodywork and fittings 11•9
11
19.13 Adjust the door lock striker by
loosening the hex nut and gently tapping
the striker in the desired direction20.2 Detach the outside handle-to-latch
rod (A), then remove the inside handle-to-
latch cable (B)20.4 Remove the latch screws (arrowed)
from the end of the door, and pull the latch
assembly through the access hole.
3261 Jaguar XJ6 19.7a Work through the door access hole (arrowed) to remove
the hinge-to-door retaining nuts from inside the door
19.7b Open the front door to access the rear door hinge-to-body
bolts (arrowed)
remove the door trim panel and watershield
as described in Section 18.
7Working through the access hole, detach
the outside handle retaining nuts (see
illustration),then pull the handle away from
the door.
8Disengage the plastic clip that secures the
outside handle-to-latch rod (see illustration).
9Remove the handle and lock cylinder
assembly from the vehicle.
10Refitting is the reverse of removal.
Inside handle and cable
11Remove the door trim panel as described
in Section 18 and peel away the watershield.
12Detach the inside handle-to-latch cable
(see illustration 20.2).
13Remove the inside handle retaining bolts
(see illustration).
14Pull the handle and cable assembly free
and remove them from the door.15Refitting is the reverse of removal.
21 Door window glass
regulator-
removal and refitting
3
1To remove the window regulator assembly,
raise the window to its full upright position,
then remove the door trim panel and
watershield as described in Section 18.
2Tape the window to the door glass frame to
secure the window in the full upright position.
3Remove the regulator and motor mounting
bolts (see illustration).
4Disconnect the electrical connector from
the window regulator motor.
5Slide the equaliser arms out of the window
glass channel and remove the regulator and
motor assembly through the service hole in
the door frame.Warning: The regulator arms are
under pressure and can cause
serious injury if the motor is
removed without locking the
sector gear. The motor and regulator can
now safely be separated.
6Refitting is the reverse of removal.
11•10 Bodywork and fittings
3261 Jaguar XJ6 20.7 The outside handle retaining nuts (arrowed) can be reached
through the access hole in the door
20.8 Detach the plastic clip securing the lock rod
20.13 After removing the cable from the latch assembly, detach
the handle retaining bolts, then pull the handle and cable
assembly free from the vehicle21.3 Detach the window regulator bolts (arrowed)
If the motor or regulator
needs replacing, it will be
necessary to lock the sector
gear to the regulator back-
plate. This can be done by fastening the
sector gear to the backplate with a bolt
inserted through one of the holes in the
backplate and sector gear and secured
with a nut. If none of the holes line up,
drill a hole through the backplate and
sector gear.
22 Door window glass-
removal and refitting
3
1Raise the window to its full upright position,
then remove the door trim panel and
watershield as described in Section 18.
2Tape the window to the door glass frame to
secure the window in the full upright position.
3Detach the regulator assembly (Section 21)
and lower it to the bottom of the door.
4Remove the window frame retaining bolts
(see illustrations).
5Remove the window frame and glass
assembly by pulling it up and out (see
illustration).
6Refitting is the reverse of removal.
23 Outside mirrors-
removal and refitting
2
1Raise the window to the fully closed
position and remove the upper half of the
door trim panel (see Section 18).
2Detach the trim cover retaining screws (see
illustration).3Disconnect the wiring plug from the mirror.
4Remove the three mirror retaining screws
and detach the mirror from the vehicle (see
illustration).
5Refitting is the reverse of removal.
24 Centre console-
removal and refitting
3
Floor console
1Disconnect the negative battery cable.Caution: If the stereo in your vehicle is
equipped with an anti-theft system, make
sure you have the correct activation code
before disconnecting the battery.
2Pry out the gear selector trim bezel (see
illustration).
3Open the console compartment and
remove the screws securing the ash tray. Pull
the ash tray back towards the compartment to
remove it (see illustrations).
4Working through the ash tray opening,
detach the plastic wingnuts securing the rear
edge of the radio trim bezel (see illustration).
5Apply the handbrake, then move the gear
Bodywork and fittings 11•11
11
22.4a Front door window frame screws 22.4b Rear door window frame screws
22.5 After removing the window frame
retaining screws, pull the window and
frame assembly up and out to remove it
3261 Jaguar XJ6 23.2 Remove the trim cover retaining screws
23.4 Disconnect the electrical connector, then detach the three
mirror retaining screws and remove the mirror from the vehicle
24.3a Open the console compartment to
access the ash tray screws (arrowed)24.2 Carefully prise out the gear selector
trim bezel
selector towards the rear of the vehicle. Pull
up on the rear half of the radio trim bezel while
gently detaching the clips securing the front,
then remove the bezel from the vehicle.
6Remove the radio and heater control
assembly (see Chapter 12).
7Remove the dashboard centre trim panel
(see Section 26), then remove the centre air
conditioning duct from the vehicle (see
illustration).
8Remove the retaining screws located in the
air conditioning duct opening (see illustration).
9Remove the plastic screws securing the
lower front section of the console (see
illustration).
10Unplug any electrical connectors that will
interfere with the removal of the console.
11Pull the console towards the rear of the
vehicle, then lift the console up over the shift
lever and remove it from the vehicle.
12Refitting is the reverse of removal.
Overhead console
13Remove the plastic screw securing the
overhead console, then carefully pull the
console out of the headliner (see illustration).
14Disconnect the electrical connectors from
the lights.
15Refitting is the reverse of removal.
25 Instrument cluster housing-
removal and refitting
2
Warning: Later models are
equipped with airbags. To
prevent the accidental deploy-
ment of the airbag, which could
cause personal injury or damage to the
airbag system, DO NOT work in the vicinity
of the steering column or instrument panel.
The manufacturer recommends that, on
airbag equipped models, the following
procedure should be left to a dealer service
department or other repair workshop
because of the special tools and techniques
required to disable the airbag system.
1Disconnect the negative battery cable. Caution: If the stereo in your vehicle is
equipped with an anti-theft system, make
sure you have the correct activation code
before disconnecting the battery.
2Remove the drivers side knee bolster (see
Section 26).
3Place the steering wheel in the full rearward
position. If the vehicle is equipped with a tilt
column, place the steering wheel in the lowest
position.
4Remove the instrument cluster housing
screws (see illustration).
5Pull the instrument cluster housing outward
to access the electrical connections on the
backside (see illustration).
6Disconnect all electrical connections from
the backside of the cluster housing and
remove the housing from the vehicle.
7Refitting is the reverse of removal.
11•12 Bodywork and fittings
24.3b Pull the ash tray towards the rear of
the vehicle to remove it - don’t pull it
straight up24.4 Working through the ash tray opening,
remove the radio trim bezel wingnuts
(arrowed) located under the trim bezel24.7 After removing the centre trim panel,
detach the air conditioning duct
24.8 Remove the retaining screws in the
air conditioning duct opening24.9 Remove the plastic screws (arrowed)
from each side of the console24.13 Remove the plastic screw, then pull
the overhead console down and unplug
the electrical connectors
3261 Jaguar XJ6
25.4 Working in the knee bolster opening,
remove two retaining screws from each
end of the instrument cluster housing25.5 Pull outward on the instrument
cluster housing and unplug the electrical
connectors from the backside
26 Dashboard trim panels-
removal and refitting
2
Warning: Later models are
equipped with airbags. To
prevent the accidental deploy-
ment of the airbag, which could
cause personal injury or damage to the
airbag system, DO NOT work in the vicinity
of the steering column or instrument panel.
The manufacturer recommends that, on
airbag equipped models, the following
procedure should be left to a dealer service
department or other repair workshop
because of the special tools and techniques
required to disable the airbag system.
Caution: If the stereo in your vehicle is
equipped with an anti-theft system, make
sure you have the correct activation code
before disconnecting the battery
Knee bolster
1Knee bolsters are located on the lower half
of the instrument panel on the driver and
passenger sides of the vehicle. The removal of
these covers will allow access to a variety of
electrical, heating and air conditioning
components.
2Detach the retaining screws along the
edges of the knee bolster (see illustration).
3Pull outward on the lower edge of the knee
bolster and detach it from the vehicle.
4Refitting is the reverse of removal.
Centre trim panel
5Carefully pull outward to detach the centre
trim panel from the instrument panel (see
illustration).
6Refitting is the reverse of removal.
Glove box
7Detach the passenger side knee bolster as
described in Steps 2 and 3.8Remove the glove box door hinge bolts
(see illustration).
9Open the glove box door, then detach it
from the vehicle.
10Detach the heater duct and the relay
mounting panel from the bottom of the glove
box.
11Detach the remaining screws securing the
upper edge of the glove box (see illustration).
12Disconnect the lamp from the glove box
and remove the assembly from the vehicle.
13Refitting is the reverse of removal.
27 Steering column cover-
removal and refitting
2
Warning: Later models are
equipped with airbags. To
prevent the accidental deploy-
ment of the airbag, which could cause
Bodywork and fittings 11•13
11
3261 Jaguar XJ6 26.2 Remove the retaining screws along the outer edge of the
knee bolster, then remove it from the vehicle
26.5 Grasp the centre trim panel with both hands, then unsnap
the retaining clips (arrowed) from the dashboard assembly
26.8 With the passenger side knee bolster removed, unscrew the
glove box door hinge bolts26.11 Remove the screws along the top edge (arrowed), pull the
glove box out and remove the lamp assembly
personal injury or damage to the airbag
system, DO NOT work in the vicinity of the
steering column or instrument panel. The
manufacturer recommends that, on airbag
equipped models, the following procedure
should be left to a dealer service
department or other repair workshop
because of the special tools and techniques
required to disable the airbag system.
1Remove the steering wheel (Chapter 10)
2Remove the knob from the rheostat
(dimmer) for the instrument panel lights (see
illustration).
3Remove the lower steering column cover
screws (see illustration), then detach the
lower cover.
4Working through the lower cover opening,
remove the four screws securing the upper
half of the cover, then pull the cover forward
and out to remove it (see illustration).
5Refitting is the reverse of removal.
28 Cowl cover-
removal and refitting
2
1Remove the windscreen wiper arms (see
Chapter 12).2Remove the retaining screws located along
the top of the cowl cover (see illustration).
3Lift the cowl cover up slightly, then detach
the electrical connectors and the spray nozzle
hoses from the backside of the cowl cover.
4Detach the cowl cover from the vehicle.
5Refitting is the reverse of removal.
29 Seats- removal and refitting
2
Front seat
1Position the seat all the way forward or all
the way to the rear to access the front seat
retaining bolts.
2Detach any bolt trim covers and remove the
retaining bolts (see illustration).
3Tilt the seat upward to access the
underneath, then unplug any electrical
connectors and lift the seat from the vehicle.
4Refitting is the reverse of removal.
Rear seat
5Remove retaining screws at the lower edge
of the seat cushion (see illustration). Then lift
up on the front edge and remove the cushion
from the vehicle.
6Detach the retaining bolts at the lower edge
of the seat back.
7Lift up on the lower edge of the seat back to
release the clips securing the top. Then
remove it from the vehicle.
8Refitting is the reverse of removal.
11•14 Bodywork and fittings
27.4 Remove the four screws securing the
upper half of the steering column cover
28.2 Remove the screws (arrowed)
located along the top of the cowl cover29.2 Use a Torx bit to remove the front
seat retaining bolts (arrowed)
3261 Jaguar XJ6 27.2 Pull off the knob from the instrument panel light rheostat
27.3 Remove the lower steering column cover screws
29.5 Detach the screws (arrowed) along
the lower edge of the seat cove