1997 FORD RANGER light

224
[ER02550(R)05/96]
17-1/2 pica
art:0090141-D
Power distribution box
%*
[ER02700(R)01/96]
Checking and Replacing Fuses
*
[ER02720(R)01/96]
If you need to check a fuse, follow these steps:
[ER02730(R)01/96]1.
Find the fuse panel, which is located in the left end of the
instrument panel. The power distribution box (described
earlier in this section) is found in the engine compartment,
mounted on a bracket attached to the left fender apron.
[ER02740(R)01/96]
To access the fuse panel, remove the fuse panel cover by
inserting your finger in the divot and pulling on the cover.
The underside of the cover contains four spare fuses. A fuse
pulling tool is located in the lower right corner of the fuse
panel in case you need to replace a blown fuse.
*
[ER02750(R)01/96]
The spare fuses for your vehicle are color coded as follows:
10 amp Ð red, 15 amp Ð light blue, 20 amp Ð natural, 30
amp Ð light green.
File:10unerr.ex
Update:Thu Mar 20 08:56:46 1997

Roadside Emergencies
239
%*
[ER25100(R)02/96]
Preparing Your Vehicle
*
[ER25200(R)02/96]1.
Your vehicle has a 12-volt starting system, so you need to
use a 12-volt jumper system. You will damage your starting
motor, ignition system, and other electrical parts if you
connect them to a 24-volt power supply (either two 12-volt
batteries in series or a 24-volt generator set).
*
[ER25300(R)02/96]2.
Do not disconnect the battery of the disabled vehicle. You
could damage the vehicle's electrical system.
*
[ER25400(R)02/96]3.
Park the booster vehicle close to the hood of the disabled
vehicle.Make sure the vehicles do not touch each other.Set
the parking brake on both vehicles and stay clear of the
engine cooling fan and other moving parts.
*
[ER25500(R)02/96]4.
Check all battery terminals and remove any excessive
corrosion before you attach the jumper cables.
*
[ER25600(R)02/96]5.
Turn on the heater fan in both vehicles. Turning on the fan
helps protect the electrical system from voltage surges. Turn
off all other switches and lights in both vehicles to prevent
possible damage to either vehicle's electrical systems.
%*
[ER25700(R)02/96]
Connecting the jumper cables
*
[ER25800(R)02/96]1.
Connect one end of the first jumper cable to the positive (+)
terminal of the discharged battery. (You can connect either
jumper cable to the positive (+) terminal, as long as you use
the same cable for both positive terminals.) Most jumper
cables have a red cable and a black cable. The red cable is
generally used for the positive terminals and the black for
the negative ones.
*
[ER25900(R)02/96]2.
Connect the other end of the first cable to the positive (+)
terminal of the booster battery.
*
[ER26000(R)02/96]3.
Connect one end of the second cable to the negative (s)
terminal of the booster battery Ð NOT to the discharged
battery.
File:10unerr.ex
Update:Thu Mar 20 08:56:46 1997

Roadside Emergencies
241
*
[ER26800(R)02/96]3.
When both vehicles are running, let them idle for a few
minutes to charge the discharged battery.
%*
[ER26900(R)02/96]
Removing jumper cables
*
[ER26910(R)02/96]1.
Always remove the jumper cables in the reverse order.
Remove the negative (s) end of the jumper cable from the
metallic surface on the engine or frame of the disabled
vehicle.
*
[ER26920(R)03/96]2.
Remove the negative (s) cable from the booster battery.
*
[ER26922(R)02/96]3.
Remove the positive (+) cable from the booster battery.
*
[ER26924(R)02/96]4.
Remove the other end of the positive (+) cable from the
discharged battery.
*
[ER26926(R)02/96]
After the vehicle is started, let it idle for a while to let the
engine ªrelearnº its idle conditions. Drive it around for a while
with all electrical accessories turned off to let the battery
recharge. Driveability may be deteriorated slightly until all drive
modes are ªrelearned.ºYou may need to use a battery charger
to fully recharge the battery.
*
[ER26928(R)03/96]
If you need to replace your battery, seeBatteryin the
Maintenance and Carechapter.
File:10unerr.ex
Update:Thu Mar 20 08:56:46 1997

Roadside Emergencies
245
[ER33000(R)01/96]
4x2ÐManualtransmission
*
[ER33100(R)01/96]
n
Release the parking brake.
[ER33200(R)01/96]
n
Place the transmission gearshift in the neutral position.
[ER33300(R)01/96]
n
Maximum speed is limited by towing equipment
manufacturer's recommendation, unlimited distance.
[ER33400(R)01/96]
4x4ÐManualshifttransfercase
*
[ER33500(R)01/96]
n
Release the parking brake.
[ER33600(R)01/96]
n
Place the transmission gearshift in the neutral position.
[ER33700(R)01/96]
n
Place the transfer case gearshift in the neutral position.
[ER33800(R)01/96]
n
Set the manual locking hubs in the FREE position.
[ER33900(R)01/96]
n
Maximum speed is 55 mph (88 km/h), unlimited distance.
[ER34000(R)01/96]
4 x 4 Electric shift transfer case
*
[ER34200(R)01/96]
n
Release the parking brake.
[ER34300(R)01/96]
n
Place the transmission gearshift in the neutral position.
[ER34400(R)05/96]
n
Ensure the transfer case is in 2H and the auto hubs are
unlocked.
[ER34600(R)01/96]
NOTE: Both the 4WD and 4WD Low indicator lights in the
instrument panel will be off when the 4WD switch is
in 2WD.
[ER34700(R)01/96]
For automatic transmissions:
[ER34800(R)01/96]
n
Maximum speed is 35 mph (56 km/h).
[ER34900(R)01/96]
n
Maximum distance is 50 miles (80 km).
File:10unerr.ex
Update:Thu Mar 20 08:56:46 1997

Roadside Emergencies
247
[ER36400(R)01/96]
To return the vehicle to a towable condition, youmust:
[ER36500(R)01/96]
n
Place the transfer case in 2WD by rotating the 4WD switch
to 2WD.
[ER36600(R)01/96]
NOTE: Both the 4WD and 4WD Low indicator lights in the
instrument cluster will be off when the transfer case
is in 2WD.
[ER36700(R)01/96]
n
After 2WD is selected, the front hubs must be ªunlockedº by
moving the vehicle in reverse direction for a minimum of ten
feet.
[ER36800(R)01/96]
n
Confirm the front hubs are unlocked by inspecting the front
drive shaft to verify it does not turn when the vehicle is
towed.
[ER36900(R)01/96]
In addition to the above guidelines, it is recommended that you
follow the instructions provided by the manufacturer of the
towing apparatus.
File:10unerr.ex
Update:Thu Mar 20 08:56:46 1997

249
Maintenance and Care
%*[MC00300(R)01/96]Service Made Easy
*[MC00400(R)01/96]Ford has two goals for servicing your vehicle.
*[MC00500(R)01/96]1.When we can, we design parts that do not need to be
serviced.
*[MC00600(R)01/96]2.We want to make servicing your vehicle as easy as possible.
To help you:
*[MC00700(R)01/96]nWe highlight do-it-yourself items in yellow in the engine
compartment so that you can find them easily.
*[MC00800(R)03/96]nWhen possible, we design parts that can be replaced without
tools.
*[MC00900(R)02/96]nWe give you a Maintenance Schedule that makes tracking
routine service for your vehicle easy. The maintenance
schedule is located in theMaintenance Schedulebooklet.
*[MC01000(R)01/96]This chapter tells you about the basic parts that you need to
check and service regularly.
*[MC01050(R)01/96]If your vehicle needs professional servicing, your dealership can
provide the parts and service required. Check your Warranty
Information Booklet to find out which parts and services are
covered. Also see the Customer Assistancechapter of this Owner
Guide.
*[MC01300(R)02/96]Ford Motor Company recommends that the Owner Maintenance
Checks listed in the Maintenance Schedule booklet be performed
for the proper operation of your vehicle. In addition to the
conditions listed in the Owner Maintenance Checklist , be alert for
any unusual noise, vibration, or other indication that your
vehicle may need service. If you do notice something unusual,
see that your vehicle is serviced promptly.
File:11unmcr.ex
Update:Thu Mar 20 08:58:43 1997

258
*
[MC13730(R)05/96]
NOTE: Ford production and aftermarket (Motorcraft) oil
filters are designed for added engine protection and
long life. If a replacement oil filter is used that does
not meet Ford material and design specifications,
startup engine noises or knock may be experienced. It
is recommended you use the appropriate Motorcraft
oil filter (or another brand meeting Ford
specifications) for your engine application.
%*
[MC13775(R)01/96]
Checking and Adding Engine Oil
*
[MC13800(R)01/96]
Since the proper amount of engine oil is important for safe
engine operation, check the oil using the dipstick each time you
put fuel in your vehicle. Remember the engine must be off, the
oil must be warm and the vehicle must be parked on level
ground.
%*
[MC13900(R)01/96]
Checking the engine oil level:
*
[MC14000(R)01/96]1.
Turn the engine off after it has warmed up and allow a few
minutes for the engine oil to drain back into the oil pan.
[MC14050(R)04/96]2.
Set the parking brake, making sure the gearshift is securely
latched in P (Park) or 1 (manual transmission).
*
[MC14100(R)01/96]3.
Open the hood. Protect yourself from engine heat.
*
[MC14200(R)01/96]4.
Locate the engine oil dipstick (highlighted in yellow) and
carefully pull it out of the engine.
*
[MC14300(R)01/96]5.
Wipe the dipstick clean and put it back into position, making
sure it is fully seated.
File:11unmcr.ex
Update:Thu Mar 20 08:58:43 1997

Maintenance and Care
259
[MC14400(R)01/96]
7-1/2 pica art:0021256-C
Engine oil dipstick
[MC14500(R)01/96]6.
Carefully, pull the dipstick out again. If the oil level is below
the ªADDº line, add engine oil as necessary. If the oil level
is beyond the letter ªFº in Full, engine damage or high oil
consumption may occur and some oil must be removed from
the engine.
*
[MC14600(R)01/96]7.
Put the dipstick back in and make sure it is fully seated.
*
[MC14800(R)01/96]
It may be necessary to add some oil between oil changes. Make
sure you use a CERTIFIED engine oil of the preferred viscosity.
Your vehicle's warranty coverage may not apply if engine
damage is caused by the use of improper engine oil.
*
[MC15000(R)01/96]
Add engine oil through the oil filler cap highlighted in yellow.
To add oil, remove the filler cap and use a funnel to pour oil
into the opening. Be careful not to overfill the engine. Recheck
the oil level after you finish adding oil.
File:11unmcr.ex
Update:Thu Mar 20 08:58:43 1997