1997 FORD F250 engine

223
Roadside Emergencies
%*
[ER00205(FM)01/96]
If the Engine Cranks but Does
Not Start or Does Not Start After
a Collision
%*
[ER00210(FM)01/96]
Fuel Pump Shut-Off Switch
*
[ER00220(FM)03/96]
If the engine cranks but does not start or does
not start even after a small collision, the fuel
pump shut-off switch may have been activated.
The shut-off switch is a device intended to stop
the fuel pump when your vehicle has been
involved in a substantial jolt.
*
[ER00225(FM)03/96]
Once the shut-off switch is activated, you must
reset the switch by hand before you can start
your vehicle.
[ER00230(F )04/96]
one third page art:0020005-C
Fuel pump shut-off switch location
File:10lterf.ex
Update:Tue May 28 08:49:52 1996
ProCarManuals.com

145
Driving
*
[GF00200(F )03/96]
Procedures for driving your vehicle will vary
depending on which type of transmission your
vehicle has.
[GF00300(F )04/96]
q
an Electronic 4-speed Automatic Transmission
(E4OD)
*
[GF00400(F )03/96]
q
a manual transmission
*
[GF00450(F )03/96]
Your vehicle is equipped with an Electronic
Powertrain Control Module that limits engine
and/or vehicle speeds with a cut-out mode to
promote durability.
%
*
[GF00500(FM)05/96]
Brakes
*
[GF00850(FM)01/96]
Front Disc Brakes
[GF00900(F )04/96]
F-250/350
*
[GF00950(F )01/96]
The front disc brakes are self-adjusting. They do
not require service other than periodic inspection
for pad wear.
*
[GF01050(F )03/96]
Rear Drum Brakes
*
[GF01100(F )03/96]
The rear drum brakes are self-adjusting.
Automatic adjustment occurs when the brakes
are applied while ªbacking up.º If normal
operation does not include much backing, adjust
the brakes when they seem ªlow,º using the
procedure underIf Brakes Do Not Grip Well or
Pedal is ªLowºin this chapter.
File:09ltgff.ex
Update:Thu May 30 15:25:49 1996
ProCarManuals.com

148
*
[GF03150(F )03/96]
RWARNING
Modifications to the suspension spring
rates and/or vehicle ride height may
adversely affect vehicle stopping ability.
*
[GF03200(F )03/96]
If Brakes Pull
*
[GF03250(F )03/96]
q
Check tire pressure.
*
[GF03300(F )03/96]
q
Perform the self-adjustment procedure
described underIf Brakes Do Not Grip Well or
Pedal is ªLow.º
*
[GF03350(F )03/96]
If pull occurs during the first 500 miles
(800 km), make 10 moderately fast stops from
40 mph (65 km/h) and then perform the
self-adjustment procedure above. It may be
necessary to repeat this operation to properly
seat new brake linings and pads.
%*
[GF03400(FM)01/96]
Stopping Distances
*
[GF03450(FM)01/96]
Stopping distances vary with different loads and
driving conditions. Use caution when
encountering new conditions and acquaint
yourself with vehicle performance. Take full
advantage of engine braking power when
slowing down.
%*
[GF03500(FM)01/96]
Applying the Brakes
*
[GF03550(FM)01/96]
Apply the brake pedal gradually. Use the
ªsqueezeº technique Ð push on the brake pedal
with a steadily increasing force. This allows the
wheels to continue to roll while you are slowing
down, which lets you steer properly.
*
[GF03600(FM)01/96]
Do not drive with your foot resting on the brake
pedal. This will increase your vehicle's stopping
distance and may also cause brake damage.
File:09ltgff.ex
Update:Thu May 30 15:25:49 1996
ProCarManuals.com

150 [GF04300(F )05/96]When the transfer case is in the N (Neutral)
position, the engine and transmission are
disconnected from the rest of the driveline.
Therefore, the vehicle is free to roll even if the
automatic transmission is in P (Park) or the
manual transmission is in gear.
*
[GF04350(F )05/96]
RWARNING
Do not leave the vehicle unattended with
the transfer case in the N (Neutral)
position. Always set the parking brake
fully and turn off the ignition when
leaving the vehicle.
[GF04400(FM)04/96]
To release the parking brake, press the service
brake pedal with your right foot and pull the
parking brake release lever.
*
[GF04500(FM)02/96]
RWARNING
If the parking brake is fully released, but
the Brake System light remains on, have
the brakes checked immediately. They
may not be working properly.
*
[GF04550(F )03/96]
The parking brake is not designed to stop a
moving vehicle, but you can use the parking
brake to stop your vehicle in an emergency if
the normal brakes fail. However, since the
parking brake applies only the rear brakes, the
stopping distance will increase greatly and the
handling of your vehicle will be adversely
affected.
File:09ltgff.ex
Update:Thu May 30 15:25:49 1996
ProCarManuals.com

151
%*
[GF05200(FM)01/96]
Steering Your Vehicle
%*
[GF05300(FM)01/96]
Your vehicle comes with power steering. Power
steering uses energy from the engine to help
steer your vehicle.
%*
[GF05350(FM)03/96]
If the amount of effort needed to steer your
vehicle changes at a constant vehicle speed, have
the power steering system checked. If the power
steering system breaks down (or if the engine is
turned off), you can steer the vehicle manually
but it takes more effort.
*
[GF05400(FM)01/96]
Never hold the steering wheel to the extreme
right or left for more than five seconds if the
engine is running. This can damage the power
steering pump.
*
[GF05450(FM)01/96]
NOTE: After any severe impact such as
striking large potholes, sliding into
curbs on icy roads, or a collision
involving the front end, observe the
steering wheel alignment. If the spokes
of the steering wheel seem to be in a
different position while going straight
down the road, have the front
suspension and steering checked for
possible damage.
% [GF07425(F )04/96]Automatic Transmission
Operation (E4OD)
[GF07475(F )04/96]
The E4OD transmission is an electronically
controlled four speed automatic transmission
with overdrive. Transmission operation is
controlled by the Powertrain Control Module
(PCM).
[GF07525(FM)04/96]
The PCM will automatically adjust transmission
operation to make up for varying conditions.
Several sensors located on the engine and
transmission such as Throttle Position, Engine
Speed, Vehicle Speed and Transmission
File:09ltgff.ex
Update:Thu May 30 15:25:49 1996
ProCarManuals.com

152Temperature are used by the PCM to shift the
transmission into a higher or lower gear when
required for the best performance and fuel
economy. For example, you may notice that the
transmission will upshift to a higher gear more
quickly when the vehicle is first driven and has
not reached normal operating temperature.
[GF07550(FM)04/96]
The PCM also controls the transmission's Torque
Converter Clutch to further raise vehicle
performance and fuel economy. The Torque
Converter Clutch will engage when the
transmission operating temperature and other
conditions determined by the PCM have been
met. Engagement of the clutch may be noted as
a decrease in engine speed after an upshift has
completed or when the driver has depressed the
throttle while driving at a steady road speed.
[GF07575(FM)01/96]
To help in troubleshooting, the PCM continually
performs self-tests on the electronic control
system and if any faults are detected, will store
them in memory. The Transmission Control
Indicator Light (TCIL), which is located on the
gearshift lever, may flash steadily if a
malfunction has been detected. If the TCIL is
flashing, contact your Ford dealer as soon as
possible. If this condition persists, damage to the
transmission could occur.
[GF07600(FM)01/96]
NOTE: The word ªOFFº located on the end of
the gearshift lever is the transmission
control indicator light (TCIL).
%*
[GF07625(FM)05/96]
Putting Your Vehicle in Gear
[GF07650(FM)04/96]
Your vehicle's gearshift is on the steering
column. The Transmission Control Switch and
indicator light are located on the end of the
gearshift lever. You can put the gearshift in any
of the several positions.
File:09ltgff.ex
Update:Thu May 30 15:25:49 1996
ProCarManuals.com

155 %
*
[GF08050(FM)05/96]
Driving
%*
[GF08075(FM)05/96]
When to usej(Overdrive)
*
[GF08100(FM)01/96]
This is the normal driving position. As the
vehicle picks up speed, automatic upshifts to
second, third and fourth gears will occur when
jOverdrive is chosen on the selector and the
transmission control switch has not been
pressed. The transmission will shift into the
correct gear when the right speed is achieved,
for the accelerator pedal position you have
chosen.
*
[GF08125(FM)05/96]
When to use Drive
*
[GF08150(FM)01/96]
You will note that there isn't a drive position on
your gearshift indicator. However, you will find
a Transmission Control Switch and an indicator
light labeled ªOverdriveº located on the end of
the gearshift lever. Press this switch and the
word ªOFFº will illuminate on the shift lever
knob. With the word ªOFFº illuminated, the
transmission will operate in gears one through
three. Operating in the Overdrive ªOFFº mode
gives more engine braking than Overdrive and
is useful for descending hills or when towing.
[GF08175(FM)01/96]
quarter page art:0020771-C
Transmission Control Switch and indicator light (located
on the gearshift lever)
File:09ltgff.ex
Update:Thu May 30 15:25:49 1996
ProCarManuals.com

156
*
[GF08200(FM)01/96]
To return the transmission to the normalj
Overdrive operation, press the transmission
control switch again. The Transmission Control
Indicator Light will not be illuminated when
Overdrive operation resumes. This switch may
be used to select O/D ON or O/D OFF any
time the vehicle is being driven.
*
[GF08225(FM)01/96]
When starting your vehicle, the overdrive system
will automatically be in the normal overdrive
mode.
[GF08250(FM)04/96]
If the Transmission Control Indicator Light is
flashing on and off steadily, a transmission
system malfunction was detected. The
transmission will operate in a failure
management mode and may have harsh
engagements, firm shift feel, or abnormal shift
schedule. If this condition persists, damage to
the transmission could occur. Contact your
dealer as soon as possible.
*
[GF08275(FM)05/96]
When to use 2 (Second)
*
[GF08300(FM)01/96]
Use 2 (Second) to start-up on slippery roads or
to provide additional engine braking on
downgrades. This position provides 2 (Second)
gear operation only.
*
[GF08325(FM)05/96]
When to use 1 (Low)
*
[GF08350(FM)01/96]
Use 1 (Low) to provide maximum engine
braking on steep downgrades. Upshifts from 1
(Low) can be made by manually shifting to 2
(Second) orj(Overdrive). Selection of 1 (Low)
gear provides only low gear operation from
start-up. Selection of 1 (Low) while at higher
speeds provides a shift to second gear, and a
shift to first gear will occur after the vehicle
decelerates to the proper speed.
File:09ltgff.ex
Update:Thu May 30 15:25:49 1996
ProCarManuals.com