1997 FORD EXPLORER brake light

ICONS
Indicates a warning. Read the
following section onWarningsfor
a full explanation of them.
Indicates that vehicle information
related to recycling and other
environmental concerns will follow.
We must all play our part in
protecting the environment.
Correct vehicle usage and the
authorized disposal of waste
cleaning and lubrication materials
are significant steps towards this
aim.
WARNINGS
How can you reduce the risk of
personal injury and prevent
possible damage to others, your
vehicle and its equipment?
In this owner's guide, answers to
such questions are contained in
comments highlighted by the
warning triangle symbol.
BREAKING-IN YOUR VEHICLE
There are no particular breaking-in
rules for your vehicle. Simply avoid
driving too briskly during the first
1,600 km (1,000 miles) of driving.
Vary speeds frequently. This is
necessary to give the moving parts
a chance to break in.
If possible, you should avoid full
use of the brakes for the first
1,600 km (1,000 miles).com_icons.01
com_warn.01
com_breaking_vehicle.01
Introduction
2

INSTRUMENT CLUSTER
LIGHTS AND CHIMES
Speed control (if equipped)
Illuminates when either the SET
ACC or RSM switches are pressed
and remains illuminated until the
speed control is either disengaged
or turned off.
O/D off indicator
O/D
OFFilluminates when the
Transmission Control Button on
the end of the gearshift lever is
pressed and the
D(Overdrive)
mode is turned off.
O/D
OFFindicates the status of the
transmission and may flash steadily
if a malfunction is detected. If the
flashing persists, have your
transmission serviced by your
dealer or qualified service
technician as soon as possible.
If the condition persists, your
transmission may be damaged.
C
012345
6
RPMx1000ABS
!PBRAKE
CHECK
ENGINE
DOOR
AJAR
EFH
H
H
PRN D 2 1THEFT
SPEED
CONTROL
4WD
4WD
LOW
O/D
OFFL
L
10MPH 205060
70
304080
90
km/h
0 0 0
10 100
1
20
1
0 0 0 0 0 0406080100
120
140
160
180
20
SPEED
CONT
O/D
OFF
uno_lights_chimes_title
uno_speed_control
uno_od_off
uno_check_engine
Instrumentation
8

Safety belt
Illuminates when the ignition is
switched on to remind you to
fasten your safety belts. For more
information, refer toUsing the
safety restraints properlyin the
Seating and safety restraints
chapter.
Brake system warning
Extinguishes when the parking
brake is released. Illumination after
releasing the parking brake
indicates low brake fluid level.
High beams
Illuminates when the headlamp
high beams are on.
Anti-lock brake system (ABS)
Momentarily illuminates when the
ignition is turned on and the
engine is off. If the light stays on
or continues to flash, the ABS
needs to be serviced.
Air bag readiness
Briefly illuminates when the
ignition is turned on. If the light
fails to illuminate, continues to
flash or remains on, have the
system serviced immediately.
Headlamps on warning chime
Sounds when the headlamps are
on, the ignition is off (and the key
!
BRAKE
ABS
uno_brake_system
com_high_beams.01
com_anti-lock_brake.01
com_air_bag.01
uno_headlamps_chime
Instrumentation
11

2. With the brake lamps, parking
lamps and headlamps off, turn the
ignition switch to ON or ACC.
3. After M/C briefly illuminates
(about two seconds), press the
brake pedal. If ªCHECK
EXTERIOR LAMPSº is displayed,
then a brake lamp is burned out. If
this message is not displayed,
proceed to the next step.
4. Turn the light switch to the
parking lamp positions. If ªCHECK
EXTERIOR LAMPSº is displayed,
then a rear side marker is burned
out. If this message is not
displayed, proceed to the next
step.
5. Turn the light switch to the
headlamp position. If ªCHECK
EXTERIOR LAMPSº is displayed,
then a low beam headlamp is
burned out.
If you use additional lights, such as
trailer lights, or replace bulbs with
equipment that is not equal to the
original Ford equipment, you may
0P RND21
UNLEADED
FUEL ONLY
RPM x 100012345
6H
C
F
E
RSM
SET
ACC
COAST OFF ONOFF
SRS
OFF
DIM
020
1030405060
70
80
90
110
120000000oooo
km/h10020406080100
120
140
160
180
Instrumentation
23

Instrument panel dimmer
control
To adjust the instrument panel
dimmer control:
²Rotate the control up to
brighten the instrument panel
lighting.
²Rotate the control down to dim
the instrument panel lighting.
Daytime running light (DRL)
system (if equipped)
The DRL system turns on the
highbeam headlamps, with a
reduced light output, when:
²the vehicle is running and the
ignition is in the On position
²the vehicle has a fully released
parking brake
²the headlamp system is in the
position
0P RND21RPM x 100012345
6H
C
F
E
RSM
SET
ACC
COAST OFF ONOFF
SRS
OFF
DIM
020
1030405060
70
80
90
110
120000000oooo
km/h10020406080100
120
140
160
180
uno_drl_lights
Controls and features
26

The Daytime Running
Light (DRL) system will
not illuminate the tail lamps and
parking lamps. Turn on your
headlamps at dusk. Failure to do
so may result in a collision.
Foglamp control (if equipped)
Press the foglamp control to
activate the foglamps.
Press the foglamp control a second
time to deactivate the foglamps.
0P RND21km/hRPM x 100012345
6H
C
FERSM
SET
ACC
COAST OFF ONOFF
SRSHI LOOFF*A/C*MAX
A/C
REW
1FF
2SIDE 1-2
3
FM 1STVOL – PUSH ON
AM
FMBASS TREBBAL FADE
AUTO
SET CLKSEEKTUNE
DISCSSCAN4DOLBY SYSTEMEJTAPE CDCOMP5SHUFFLE
6
PUSH020
1030405060
70
80
90
110
120000000ooookm/h10020406080100
120
140
160
180
uno_foglamp_switch uno_parking_brake
Controls and features
27

To return to a set speed
²Press RSM. For RSM to operate,
the vehicle speed must be faster
than 48 km/h (30 mph).
To disengage speed control
²Depress the brake pedal or
²Depress the clutch pedal (if
equipped)
Disengaging the speed control will
not erase the previously
programmed set speed.
Pressing OFF will erase the
previously programmed set speed.
Indicator light
Lights when the speed control is
turned on and remains lit until
either the speed control or the
ignition is turned off.
RSM
SET
ACC
COAST
SPEED
CONT
uno_disengaging
uno_light
uno_tilt_steer
Controls and features
43

Make sure the following lights
illuminate briefly. If a light fails to
illuminate, have the vehicle
serviced.
²If the driver's safety belt is
fastened, the
light does not
illuminate.
STARTING
Special conditions when
starting
Starting the engine
1. Turn the key to 5 (Start)
without pressing the accelerator
and release as soon as the engine
starts. The key will return to 4
(On).
2. If the engine does not start
within five seconds, wait ten
seconds and try again.
3. If the engine does not start in
two attempts OR the temperature
is below Ð12ÉC (10ÉF), depress
0ABS
- +
P RND21RPM x 1000
12345
6- +
H
H
L LH
C
F
E
!BRAKE
CHECK
GAGE
0
20
1030405060
70
80
90
110
120000000
oooo
10020406080100
120
140
160
180
MPH km/hDOOR
AJARCHECK
GAUGE
O/D
OFF4WD
LOW 4WD SPEED
CONT
3
2
1
5
4
uno_special_conditions_title
uno_starting_vehicle
Starting
115