1997 FORD AEROSTAR key

101
*
[SS00265(ALL)01/96]
To remove seat assembly:
[SS00270(ALL)04/96]
1. Disengage the lap/shoulder safety belt from
the seat by inserting a key or screwdriver
into the slot in the detachable anchor and
lifting upward. Stow the tongue end of the
detachable anchor as shown in the
illustration.
[SS00275(ALL)01/96]
three fourths page art:0095047-A
Location of the detachable anchor warning label on safety
belt
File:06cpssa.ex
Update:Thu Jun 13 08:56:07 1996

113
*
[SS04340(ALL)02/96]
3. A clicking sound will continue to be heard
as the belt is allowed to retract. This
indicates that the retractor is in the
automatic locking mode.
*
[SS04350(ALL)02/96]
NOTE: When the combination lap/shoulder
belt is unbuckled and allowed to
retract completely, the retractor will
switch to the vehicle sensitive
(emergency) locking mode. See the
detailed instructions underSafety Seats
for Childrenin this chapter.
[SS04375(ALL)01/96]
Two Passenger Bench or Bedseat
(If Equipped)
[SS04400(ALL)04/96]
In addition to anchorages in the floor and roof
structures, some rear safety belts have a
detachable anchor mounted to the outboard side
of the rear seats. This should remain attached,
except when removing the rear seats.
[SS04800(ALL)01/96]
Disengaging rear seat safety belts for seat
removal
[SS04850(ALL)01/96]
In order to remove the rear seat, the safety belt
must be disengaged from the seat. To disengage
the safety belt from the seat, insert a key or
small screwdriver into the slot provided on the
detachable anchor. Then lift upward.
File:06cpssa.ex
Update:Thu Jun 13 08:56:07 1996

127
*
[SS12700(ALL)05/96]
q
and the electrical wiring which connects the
components.
*
[SS12800(ALL)05/96]
The diagnostic module monitors its own internal
circuits and the supplemental air bag electrical
system readiness (including the impact sensors),
the system wiring, the air bag system readiness
light, the air bag backup power and the air bag
igniters.
*
[SS12900(ALL)05/96]
Determining if System Is Operational
*
[SS13000(ALL)05/96]
The Air Bag Supplemental Restraint System uses
a readiness light and a tone to indicate the
condition of the system. The readiness light is in
the instrument cluster. When you turn the
ignition key to ON, this light will illuminate for
approximately six (6) seconds and then turn off.
This indicates that the system is operating
normally. NOTE: Routine maintenance of the air
bag system is not required.
%*
[SS13100(ALL)05/96]
A problem with the system is indicated by one
or more of the following:
*
[SS13200(ALL)05/96]
q
the readiness light will either flash or stay lit,
*
[SS13300(ALL)05/96]
q
the readiness light will not light immediately
after ignition is turned on,
%*
[SS13400(ALL)05/96]
q
a group of five beeps will be heard. The tone
pattern will repeat periodically until the
problem and light are repaired.
*
[SS13500(ALL)05/96]
If any of these things happen, even
intermittently, have the Air Bag Supplemental
Restraint System serviced at your Ford or
Lincoln-Mercury dealer immediately. Unless
serviced, the system may not function properly
in the event of a collision.
File:06cpssa.ex
Update:Thu Jun 13 08:56:07 1996

153
Starting
%*
[TO04800(ALL)01/96]
Fuel-Injected Engines
*
[TO04900(ALL)01/96]
When starting a fuel-injected engine,the most
important thing to remember is to avoid
pressing down on the accelerator before or
during starting. Only use the accelerator when
you have problems getting your vehicle started.
SeeStarting Your Enginein this chapter for
details about when to use the accelerator while
you start your vehicle.
*
[TO05150(ALL)01/96]
Starting Your Vehicle
%*
[TO05200(ALL)01/96]
Preparing to Start Your Vehicle
*
[TO05300(ALL)02/96]
RWARNING
Do not start your vehicle in a closed
garage or in other enclosed areas. Exhaust
fumes can be toxic. Always open the
garage door before you start the engine.
*
[TO05400(ALL)01/96]
Before you start your vehicle, do the following:
*
[TO05500(ALL)01/96]
1. Make sure all occupants in the vehicle
buckle their safety belts. SeeSafety Restraints
in the Index for more details.
*
[TO05600(ALL)01/96]
2. Make sure the headlamps and other
accessories are turned off when starting.
*
[TO05750(ALL)01/96]
3. Make sure that the gearshift is in P (Park)
and the parking brake is set before you turn
the key.
*
[TO06015(ALL)02/96]
Before you start your vehicle, you should test
the warning lights on the instrument panel to
make sure that they work. Refer to the
Instrumentationchapter.
File:08cptoa.ex
Update:Thu Jun 6 14:43:40 1996

154 %
*
[TO06200(ALL)01/96]
Starting Your Engine
*
[TO06300(ALL)01/96]
To start your engine:
*
[TO06400(ALL)01/96]
1. Follow the steps underPreparing to Start
Your Vehicleat the beginning of this section.
*
[TO06425(ALL)01/96]
2. Turn the ignition key to the ON position.
*
[TO06451(ALL)01/96]
3. DO NOT depress the accelerator pedal when
starting your engine. DO NOT use the
accelerator while the vehicle is parked.
*
[TO06475(ALL)01/96]
4. Turn the key to the START position
(cranking) until the engine starts. Allow the
key to return to the ON position after the
engine has started.
*
[TO06501(ALL)05/96]
If you have difficulty in turning the key,
rotate the steering wheel slightly because it
may be binding.
%*
[TO06505(ALL)01/96]
For a cold engine:
*
[TO06510(ALL)01/96]
q
At temperatures10ÊF (-12ÊC) andbelow:If
the engine does not start infifteen (15)
secondson the first try, turn the key to OFF,
wait approximately ten (10) seconds so you
do not flood the engine, then try again.
*
[TO06515(ALL)01/96]
q
At temperaturesabove10ÊF(-12ÊC):If the
engine does not start infive (5) secondson
the first try, turn the key to OFF, wait
approximately ten (10) seconds so you do not
flood the engine, then try again.
%*
[TO06530(ALL)01/96]
For a warm engine:
*
[TO06551(ALL)01/96]
q
Do not hold the key in the START position
for more thanfive (5) secondsat a time. If
the engine does not start within five (5)
seconds on the first try, turn the key to the
OFF position. Wait a few seconds after the
starter stops, then try again.
File:08cptoa.ex
Update:Thu Jun 6 14:43:40 1996

155
*
[TO06575(ALL)01/96]
Whenever you start your vehicle, release the key
as soon as the engine starts. Excessive cranking
could damage the starter.
*
[TO06601(ALL)01/96]
After starting, allow the engine to idle for a few
seconds before driving away.
%*
[TO06625(ALL)05/96]
NOTE: Your vehicle is equipped with a
brake-shift interlock feature. This
feature prevents you from shifting
from P (Park) unless you have the
brake pedal depressed. (The ignition
must be in the ON position.) If you
cannot shift from P (Park) with the
brake pedal depressed:
*
[TO06627(ALL)05/96]
1. Apply the parking brake.
*
[TO06629(ALL)05/96]
2. Remove the key.
*
[TO06631(ALL)05/96]
3. Insert the key and rotate it one position
clockwise (ignition in the OFF position).
*
[TO06633(ALL)05/96]
4. Apply the brake pedal and shift to N
(Neutral). (If the vehicle is shifted back to P
[Park], you must repeat the previous steps.)
*
[TO06635(ALL)05/96]
5. Start the vehicle.
*
[TO06637(ALL)05/96]
If you need to shift out of P (Park) by using the
alternate procedure described above, it is
possible that a fuse has blown and that your
brakelamps may also not be functional. Please
refer to the chapter titledRoadside Emergenciesin
this Owner Guide for instructions on checking
and replacing fuses.
*
[TO06640(ALL)05/96]
RWARNING
DO NOT DRIVE YOUR VEHICLE UNTIL
YOU VERIFY THAT THE BRAKELAMPS
ARE WORKING.
File:08cptoa.ex
Update:Thu Jun 6 14:43:40 1996

156
*
[TO06800(ALL)01/96]
If the engine still does not start after two
attempts:
*
[TO06825(ALL)01/96]
1. Turn the ignition key to the OFF position.
*
[TO06851(ALL)01/96]
2. Press the accelerator all the way to the floor
and hold it.
*
[TO06876(ALL)01/96]
3. Turn the ignition key to the START position.
*
[TO06900(ALL)01/96]
4. Release the ignition key when the engine
starts.
*
[TO06925(ALL)03/96]
5. Release the accelerator gradually as the
engine speeds up.
*
[TO06951(ALL)05/96]
If the engine still does not start, the fuel pump
shut-off switch may have been activated. For
directions on how to reset the switch seeFuel
Pump Shut-Off Switchin the index.
%*
[TO07300(ALL)01/96]
A computer system controls the engine's idle
speed. When you start your vehicle, the engine's
idle speed normally runs high. These faster
engine speeds will make your vehicle coast
slightly faster than its normal idle speed. It
should, however, slow down after a short time.
If it does not, have the idle speed checked.
*
[TO07390(ALL)01/96]
If the engine idle speed does not slow down
automatically, do not allow your vehicle to idle
for more than 10 minutes. Have the vehicle
checked.
*
[TO07400(ALL)01/96]
RWARNING
Extended idling at high engine speeds can
produce very high temperatures in the
engine and exhaust system, creating the
risk of fire or other damage.
File:08cptoa.ex
Update:Thu Jun 6 14:43:40 1996

159
*
[TO08560(ALL)03/96]
If your engine cranks but does not start after a
collision or substantial jolt:
*
[TO08570(ALL)01/96]
1. Turn the ignition key to the OFF position.
*
[TO08580(ALL)03/96]
2. Check under the vehicle for leaking fuel.
*
[TO08590(ALL)01/96]
3. If you do not see or smell fuel, push the red
reset button down. If the button is already
set, you may have a different mechanical
problem.
*
[TO08600(ALL)01/96]
4. Turn the ignition key to the ON position for
a few seconds, then turn it to the OFF
position.
*
[TO08610(ALL)03/96]
5. Check under the vehicle again for leaking
fuel.If you see or smell fuel, do not start
your vehicle again.If you do not see or
smell fuel, you can try to start your vehicle
again.
*
[TO08620(ALL)01/96]
6. Check all vehicle warning lights before
driving the vehicle.
[TO08630(ALL)04/96]
quarter page art:0020107-A
Reset button for fuel pump shut-off switch
*
[TO09200(ALL)02/96]
RWARNING
Do not start your vehicle in a closed
garage or in other enclosed areas. Exhaust
fumes can be toxic. Always open the
garage door before you start the engine.
File:08cptoa.ex
Update:Thu Jun 6 14:43:40 1996