1996 TOYOTA TERCEL filter

IN0253
WRONG CORRECT
IN0252
WRONG CORRECT IN-6
- INTRODUCTIONREPAIR INSTRUCTIONS
6 Author
: Date
:
1996 TERCEL (RM440U)
(k) Care must be taken when jacking up and supporting the
vehicle. Be sure to lift and support the vehicle at the prop-
er locations (See page IN-8).
Cancel the parking brake on the level place and
shift the transmission in Neutral (or N position).
When jacking up the front wheels of the vehicle at
first place stoppers behind the rear wheels.
When jacking up the rear wheels of the vehicle at
first place stoppers before the front wheels.
When either the front or rear wheels only should be
jacked up, set rigid racks and place stoppers in front
and behind the other wheels on the ground.
After the vehicle is jacked up, be sure to support it
on rigid racks . It is extremely dangerous to do any
work on a vehicle raised on a jack alone, even for
a small job that can be finished quickly.
(l) Observe the following precautions to avoid damage to the
following parts:
(1) Do not open the cover or case of the ECU unless
absolutely necessary. (If the IC terminals are
touched, the IC may be destroyed by static electric-
ity.)
(2) To disconnect vacuum hoses, pull off the end, not
the middle of the hose.
(3) To pull apart electrical connectors, pull on the con-
nector itself, not the wires.
(4) Be careful not to drop electrical components, such
as sensors or relays. If they are dropped on a hard
floor, they should be replaced and not reused.
(5) When steam cleaning an engine, protect the elec-
tronic components, air filter and emission-related
components from water.
(6) Never use an impact wrench to remove or install
temperature switches or temperature sensors.

- INTRODUCTIONTERMS
IN-37
1996 TERCEL (RM440U) HO2S
Heated Oxygen SensorHeated Oxygen Sensor (HO2S)
IACIdle Air ControlIdle Speed Control (ISC)
IATIntake Air TemperatureIntake or Inlet Air Temperature
ICMIgnition Control Module-
IFIIndirect Fuel InjectionIndirect Injection (IDL)
IFSInertia Fuel-Shutoff-
ISCIdle Speed Control-
KSKnock SensorKnock Sensor
MAFMass Air FlowAir Flow Meter
MAPManifold Absolute PressureManifold Pressure
Intake Vacuum
MCMixture Control
Electric Bleed Air Control Valve (EBCV)
Mixture Control Valve (MCV)
Electric Air Control Valve (EACV)
MDPManifold Differential Pressure-
MFIMultiport Fuel InjectionElectronic Fuel Injection (EFI)
MILMalfunction Indicator LampCheck Engine Lamp
MSTManifold Surface Temperature-
MVZManifold Vacuum Zone-
NVRAMNon-V olatile Random Access Memory-
O2SOxygen SensorOxygen Sensor, O2 Sensor (O2S)
OBDOn-Board DiagnosticOn-Board Diagnostic System (OBD)
OCOxidation Catalytic ConverterOxidation Catalyst Convert (OC), CCo
OPOpen LoopOpen Loop
PAIRPulsed Secondary Air InjectionAir Suction (AS)
PCMPowertrain Control Module-
PNPPark/Neutral Position-
PROMProgrammable Read Only Memory-
PSPPower Steering Pressure-
PTOXPeriodic Trap OxidizerDiesel Particulate Filter (DPF)
Diesel Particulate Trap (DPT)
RAMRandom Access MemoryRandom Access Memory (RAM)
RMRelay Module-
ROMRead Only MemoryRead Only Memory (ROM)
RPMEngine SpeedEngine Speed
SCSuperchargerSupercharger
SCBSupercharger BypassE-ABV
SFISequential Multiport Fuel InjectionElectronic Fuel Injection (EFI), Sequential Injection
SPLSmoke Puff Limiter-
SRIService Reminder Indicator-
SRTSystem Readiness Test-
STScan Tool-
TBThrottle BodyThrottle Body
TBIThrottle Body Fuel InjectionSingle Point Injection
Central Fuel Injection (Ci)
TCTurbochargerTurbocharger
TCCTorque Converter ClutchTorque Converter

MA00R-19
MA0659
Upper Lower
- MAINTENANCEENGINE
MA-5
43 Author
: Date
:
1996 TERCEL (RM440U)
ENGINE
INSPECTION
HINT:
Inspect these items when the engine is cold.
1. REPLACE TIMING BELT (See pages EM-12 and
EM-17)
2. INSPECT DRIVE BELTS (See pages CH-2, SR-3 and
AC-18)
3. INSPECT AIR FILTER
(a) Visually check that the air filter is not excessively dirty,
damaged or oily.
If necessary, replace the air filter.
(b) Clean the air filter with compressed air.
First blow from the upper side thoroughly, then blow off
the lower side of the air filter.
4. REPLACE AIR FILTER
Replace the air filter with a new one.
5. REPLACE SPARK PLUGS (See page IG-1)
6. REPLACE ENGINE OIL AND OIL FILTER (See page
LU-3)
7. REPLACE ENGINE COOLANT (See page CO-2)
8. INSPECT CHARCOAL CANISTER (See page EC-5)
9. REPLACE GASKET IN FUEL TANK CAP (See page
EC-5)
10. INSPECT FUEL LINES AND CONNECTIONS (See
page EC-5)
11. INSPECT EXHAUST PIPES AND MOUNTINGS
Visually check the pipes, hangers and connections for severe
corrosion, leaks or damage.
12. ADJUST VALVE CLEARANCE (See page EM-4)

PP3IP-01
- PREPARATIONENGINE MECHANICAL
PP-5
1996 TERCEL (RM440U)
RECOMMENDED TOOLS
09040-0001 1Hexagon Wrench Set .Oil filter union
09043-50080Bi-hexagon Wrench 8 mm .Cylinder head bolt
09090-04020Engine Sling DeviceFor suspending engine
09200-00010Engine Adjust Kit .
09258-00030Hose Plug Set .Plug for vacuum hose, fuel hose, etc.
09904-00010Expander Set .Intake camshaft snap ring

PP193-01
- PREPARATIONLUBRICATION
PP-19
66 Author
: Date
:
1996 TERCEL (RM440U)
LUBRICATION
SST (Special Service Tools)
09032-00100Oil Pan Seal Cutter
09228-06501Oil Filter Wrench

PP196-04
PP-22
- PREPARATIONLUBRICATION
1996 TERCEL (RM440U)
LUBRICANT
ItemCapacityClassification
Engine oil
Drain and refill w/o Oil filter change
w/ Oil filter change
Dry fill
2.6 liters (2.7 US qts, 2.3 lmp. qts)
2.8 liters (3.0 US qts, 2.5 lmp. qts)
3.7 liters (3.9 US qts, 3.3 lmp. qts)
API grade SH, Energy-Conserving II multigrade
engine oil or ILSAC multigrade engine oil and
recommended viscosity oil

SS0N6-04
SS-8
- SERVICE SPECIFICATIONSENGINE MECHANICAL
1996 TERCEL (RM440U)
TORQUE SPECIFICATION
Part tightenedN´mkgf´cmft´lbf
Cylinder head cover x Cylinder head7.07061 in.´lbf
No. 2 idler pulley x Cylinder head2828020
Camshaft timing pulley x Camshaft5151037
No. 1 idler pulley x Cylinder block18.518513
Crankshaft pulley x Crankshaft1551,55011 2
No. 2 crankshaft pulley x Crankshaft pulley1919514
RH engine mounting insulator x RH engine mounting bracket6465047
RH engine mounting insulator x Body7374054
No. 1 engine hanger x Cylinder head2121015
No. 2 engine hanger x Cylinder head5353038
Cylinder head x Cylinder block 1st
2nd45
Turn 90°450
Turn 90°33
Turn 90°
Camshaft bearing cap x Cylinder head131309
Intake manifold x Cylinder head19.519514
Intake manifold stay x Intake manifold2020015
Intake manifold stay x Cylinder block2020015
Exhaust manifold x Cylinder head4848035
Exhaust manifold stay x Cylinder block4040029
Exhaust manifold stay x Exhaust manifold4040029
Exhaust manifold heat insulator x Exhaust manifold8.08069 in.´lbf
Water outlet housing x Cylinder head3030022
Camshaft position sensor x Cylinder head8.08069 in.´lbf
EGR VSV x Cylinder head17.517513
EGR valve x Cylinder head17.517513
EGR pipe x EGR valve4040029
EGR pipe x Intake manifold3030022
PS ump bracket x Cylinder head4344032
Fuel inlet hose x Fuel filter2930022
Front exhaust pipe x Exhaust manifold6263049
Connecting rod cap x Connecting rod4040029
Crankshaft bearing cap x Cylinder block5858042
Rear oil seal retainer x Cylinder block7.57565 in.´lbf
Oil filter union x Cylinder block2525018
Oil pressure switch x Cylinder block131309
RH engine mounting bracket x Cylinder block5959043
Knock sensor x Cylinder block4545033
Generator bracket x Cylinder block2424018
Rear end plate x Cylinder block101007
Flywheel x Crankshaft9090065
Drive plate x Crankshaft9090065
Drive plate x Torque converter clutch2525018
A/C compressor bracket x Cylinder block2728020
PS pump adjusting strut x Cylinder block2121015

SS0N8-03
SS-12
- SERVICE SPECIFICATIONSMFI
1996 TERCEL (RM440U)
TORQUE SPECIFICATION
Part tightenedN´mkgf´cmft´lbf
Fuel line Union bolt type
Flare nut type29
30290
30022
23
Fuel inlet hose x Fuel filter2929022
Fuel outlet pipe x Fuel pump bracket2929022
Fuel tank x Fuel pump set bolt3.43530 in.´lbf
Fuel pressure regulator x Delivery pipe8.08069 in.´lbf
Fuel return pipe x Delivery pipe8.08069 in.´lbf
Fuel return pipe x Fuel pressure regulator2020014
Delivery pipe x Cylinder head1919014
Fuel inlet hose x Delivery pipe3030023
Fuel pump bracket x Fuel cut-off valve1.51513 in.´lbf
Fuel tank x Fuel tank filler pipe3.43530 in.´lbf
Fuel tank x Body3334025
Throttle body x Intake manifold19.519514
Main heated oxygen sensor x Exhaust manifold4444032
Sub heated oxygen sensor x Exhaust pipe4444032
Knock sensor x Cylinder block4545033