1996 TOYOTA TERCEL transmission oil

SS0KQ-04
- SERVICE SPECIFICATIONSMANUAL TRANSAXLE
SS-27
1996 TERCEL (RM440U)
TORQUE SPECIFICATION
Part tightenedN´mkgf´cmft´lbf
Transaxle x Engine 17 mm head
14 mm head
10 mm head64
46
7.4650
470
7547
34
65 in.´lbf
Engine left mounting bracket x Insulator4849036
Engine rear mounting insulator x Body7880058
Engine rear mounting insulator x Bracket B bolt
C bolt64
90650
92047
67
Front exhaust pipe clamp set bolt1919014
Front exhaust pipe x Exhaust manifold6263046
Starter x Transaxle3940029
Clutch release cylinder x Transaxle121209
Shift lever assembly x Body121209
Grommet retainer x Body4.95043 in.´lbf
Retainer x Body4.95043 in.´lbf
Output shaft front bearing lock plate set bolt1111 58
Transmission case x Transaxle case2930022
Reverse shift arm bracket1717513
Straight screw plug (Reverse restrict pin) (C151)
Straight screw plug13
13130
1309
9
Straight screw plug (Shift fork shaft)2525018
Straight screw plug (Lock ball assembly) (C151)
Straight screw plug (C141)39
39400
40029
29
Reverse idler gear shaft lock bolt2930022
Rear bearing retainer2728020
Output shaft lock nut11 81,20087
Shift fork and shift head x Shift fork shaft1616012
Shift and select lever assembly2020014
Transmission case x Transmission case cover1818513
Back-up light switch4041030
Filler and drain plugs3940029
Ring gear x Differential case1241,26091
Speedometer driven gear1111 58
Control lever housing support bracket x Transmission case1111 58
Selecting bellcrank assembly x Transmission case2525018
Shift and select lever shaft assembly lock bolt2930022
Transaxle case receiver x Transaxle case1111 58
No. 1 and No. 2 oil receiver pipe1717513

MA0659
Outside
Inside
DI-8
- DIAGNOSTICSENGINE
1996 TERCEL (RM440U)
YES
2 Is engine cranked ?
NO Proceed to ST-13, ST-28, ST-31 and continue
to troubleshoot.
YES
3 Does engine start ?
NO Go to step 7.
YES
4 Check air filter.
PREPARATION:
Remove the air filter.
CHECK:
Visual check that the air cleaner element is not excessively dirty
or oily.
HINT:
If necessary, clean the filter with compressed air. First blow from
inside thoroughly, then blow from outside of filter.
NG Repair or replace.
OK
5 Check engine idle speed.
PREPARATION:
(a) Warm up engine to normal operating temperature.
(b) Switch off all accessories.
(c) Switch off air conditioning.
(d) Shift transmission into ºNº position.

SF199-02
- MFIIDLE AIR CONTROL (IAC) VALVE
MF-33
557 Author
: Date
:
1996 TERCEL (RM440U)
IDLE AIR CONTROL (IAC) VALVE
ON-VEHICLE INSPECTION
1. INSPECT IAC VALVE OPERATION
(a) Initial conditions:

Engine at normal operating temperature

Idle speed set correctly

Transmission in neutral position
(b) Using SST, connect terminals TE1 and E1 of the DLC1.
SST 09843-18020
(c) After engine rpm is kept at 900 - 1,300 rpm for 5 seconds,
check that it returns to idle speed.
If the rpm operation is not as specified, check the IAC valve, wir-
ing and ECM.
(d) Remove the SST from the DLC1.
SST 09843-18020
2. INSPECT IAC VALVE RESISTANCE
NOTICE:
ºColdº and ºHotº in the following sentences express the temper-
ature of the coils themselves. ºColdº is from -10°C (14°F) to 50°C
(122°F) and ºHotº is from 50°C (122°F) to 100°C (212°F).
(a) Disconnect the IAC valve connector.
(b) Using an ohmmeter, measure the resistance between ter-
minal +B and other terminals (RSC, RSO).
Resistance:
Cold17.0 - 24.5 W
Hot21.5 - 28.5 W
If resistance is not as specified, replace the IAC valve.
(c) Reconnect the IAC valve connector.

Z18912
Oil Receiver Pipe
Straight Screw Plug (C141)


Slotted Spring Pin (C151)
Outer Race
Plate Washer Reverse Restrict Pin (C151)
Oil Receiver Pipe
x13 Transmission Case
 Lock Ball Assembly (C151)


Back-Up Light Switch
Lock Bolt
Breather Plug
Shift and Select Lever
Shaft Assembly
Selecting Bellcrank Assembly
Oil Seal
x9
Transmission Case
Cover (C141) Drain Plug
 Non-reusable part

Precoated partTransmission Case
Cover (C151)
x9
Gasket Gasket
Filler Plug


Straight Screw Plug
Straight Screw Plug (C141)
Gasket MX-8
- MANUAL TRANSAXLEMANUAL TRANSAXLE ASSEMBLY
720 Author
: Date
:
1996 TERCEL (RM440U)

MX07V-03
Z16129
SST
MT0081
Matchmarks
MT0083
MT0084
N00098
SST MX-36
- MANUAL TRANSAXLEDIFFERENTIAL CASE
1996 TERCEL (RM440U)
DISASSEMBLY
1. REMOVE SIDE BEARING FROM DIFFERENTIAL
CASE
(a) Using SST, remove the bearings from both sides of the
case.
SST 09950- 00020, 09950- 00030, 09950- 60010
(09951-00360)
(b) Remove the speedometer drive gear from the RH side.
2. REMOVE RING GEAR
(a) Place matchmarks on the ring gear and case.
(b) Remove the 6 bolts.
(c) Using a plastic hammer, remove the ring gear from the
case.
3. INSPECT SIDE GEAR BACKLASH
Using a dial indicator, measure the backlash of one side gear
while holding one pinion toward the case.
Standard backlash:
0.05 - 0.20 mm (0.0020 - 0.0079 in.)
If the backlash is not within the specification, install the correct
thrust washer to the side gears.
4. DISASSEMBLE DIFFERENTIAL CASE
(a) Using a pin punch and hammer, remove the pinion shaft
straight pin.
(b) Remove the pinion shaft from the case.
(c) Remove the 2 pinion gears and side gears with the 4
thrust washers from each gear.
5. Transmission Case Side:
IF NECESSARY, REPLACE OIL SEAL AND SIDE
BEARING OUTER RACE
(a) Using a screwdriver and hammer, remove the oil seal.
(b) Using SST, remove the outer race and plate washer.
SST 09612-65014
(c) Place the plate washer into the case.