LU08B-04
P20919
SST
LU0490
SST
- LUBRICATIONOIL AND FILTER
LU-3
1996 TERCEL (RM440U)
REPLACEMENT
CAUTION:
Prolonged and repeated contact with mineral oil will
result in the removal of natural fats from the skin,
leading to dryness, irritation and dermatitis. In addi-
tion, used engine oil contains potentially harmful
contaminants which may cause skin cancer. Ade-
quate means of skin protection and washing facilities
should be provided.
Care should be taken, therefore, when changing en-
gine oil, to minimize the frequency and length of time
your skin is exposed to used engine oil. Protective
clothing and gloves, that cannot be penetrated by oil,
should be worn. Wash your skin throughly with soap
and water, or use waterless hand cleaner, to remove
any used engine oil. Do not use gasoline, thinners, or
solvents.
In order to preserve the environment, used oil must
be disposed of only at designated disposal sites.
1. DRAIN ENGINE OIL
(a) Remove the oil filler cap.
(b) Remove the oil drain plug and drain the oil into a contain-
er.
2. REPLACE OIL FILTER
(a) Using SST, remove the oil filter.
SST 09228-06501
(b) Clean the filter contact surface on the filter mounting.
(c) Lubricate the filter rubber gasket with engine oil.
(d) Tighten filter until the gasket contacts seat of the filter
mounting. Then using SST, give it an additional 3/4 turn
to seat the filter.
SST 09228-06501
3. FILL WITH ENGINE OIL
(a) Clean and install the oil drain plug with a new gasket.
Torque: 25 N´m (250 kgf´cm, 18 ft´lbf)
(b) Fill the engine with new oil.
Oil grade: See step 1 in oil oressure check
Oil capacity:
Drain and refill w/ Oil filter change
w/o Oil filter change2.8 liters (3.0 US qts, 2.5 lmp. qts)
2.6 liters (2.7 US qts, 2.3 lmp. qts)
Dry fill3.7 liters (3.9 US qts, 3.3 lmp. qts)
F01195
Bolt
Adjusting
ValueSet Bolt
15'
30'Adjusting Bolt90105-15001 90105-15004 90105-15005 90105-15006
45'
1°00'
1°15'
1°30'121212121 Dot 2 Dots 3 Dots
W00533
W00533
SA-6
- SUSPENSION AND AXLEFRONT WHEEL ALIGNMENT
822 Author: Date:
1996 TERCEL (RM440U)
If the camber is not within the specification, using the table be-
low, estimate of how much additional camber adjustment will be
required, and select the camber adjusting bolt.
(i) Follow the above mentioned steps again. Between step
(b) and (c), exchange 1 or 2 selected bolts.
HINT:
When exchanging the 2 bolts, exchange 1 bolt for each time.
6. ADJUST TOE-IN
(a) Remove the boot clamps.
(b) Loosen the tie rod end lock nuts.
(c) Turn the left and right rack ends an equal amount to adjust
the toe-in.
Toe-in
(total)A + B: 0.1° ± 0.2°
C - D: 1 ± 2 mm (0.04 ± 0.08 in.)
HINT:
Try to adjust the toe-in to the center value.
Make sure that the lengths of the left and right rack ends
are the same.
Tie rod end length difference: 1.5 mm (0.059 in.) or
less
(d) Torque the tie rod end lock nuts.
Torque: 47 N´m (480 kgf´cm, 35 ft´lbf)
(e) Place the boots on the seat and install the clamps to them.
HINT:
Make sure that the boots are not twisted.
BR2237
BR0RJ-01
BR2238
GOOD NO GOOD
1st2nd3rd
- BRAKEBRAKE BOOSTER ASSEMBLY
BR-15
889 Author: Date:
1996 TERCEL (RM440U)
BRAKE BOOSTER ASSEMBLY
ON-VEHICLE INSPECTION
1. OPERATING CHECK
(a) Depress the brake pedal several times with the engine off
and check that there is no change in the pedal reserve
distance.
(b) Depress the brake pedal and start the engine. If the pedal
goes down slightly, operation is normal.
2. AIR TIGHTNESS CHECK
(a) Start the engine and stop it after 1 or 2 minutes. Depress
the brake pedal several times slowly.
If the pedal goes down farthest the 1st time, but gradually rises
after the 2nd or 3rd time, the booster is air tight.
(b) Depress the brake pedal while the engine is running, and
stop the engine with the pedal depressed. If there is no
change in the pedal reserve travel after holding the pedal
for 30 seconds, the booster is air tight.
