1996 TOYOTA T100 torque

Downloaded from www.Manualslib.com manuals search engine SS089−02
− SERVICE SPECIFICATIONSAUTOMATIC TRANSMISSION
SS−49
223 Author: Date:
1996 TOYOTA T100 (RM449U)
AUTOMATIC TRANSMISSION
SERVICE DATA
Line pressure (Wheel locked)
(3RZ−FE)
Engine idling
D position
R position
at stall (Throttle valve fully opened)
D position
R position
(5VZ−FE)
Engine idling
D position
R position
at stall (Throttle valve fully opened)
D position
R position
363 − 422 kPa (3.7 − 4.2 kgf/cm2, 53 − 61 psi)
490 − 588 kPa (5.0 − 6.0 kgf/cm2, 71 − 85 psi)
932 − 1,177 kPa (9.5 − 12.0 kgf/cm
2, 135 − 171 psi)
1,294 − 1,638 kPa (13.2 − 16.7 kgf/cm2, 188 − 238 psi)
363 − 422 kPa (3.7 − 4.2 kgf/cm
2, 53 − 61 psi)
608 − 696 kPa (6.2 − 7.1 kgf/cm2, 88 − 101 psi)
902 − 1,147 kPa (9.2 − 11.7 kgf/cm
2, 131 − 166 psi)
1,432 − 1,942 kPa (14.6 − 19.8 kgf/cm2, 208 − 282 psi)
Engine stall revolution (D and R positions) 3RZ−FE
5VZ−FE1,950 ± 150 rpm
2,150 ± 150 rpm
Time lag N → D position
N → R positionLess than 1.2 seconds
Less than 1.5 seconds
Engine idle speed
(A/C OFF and N position)
700 ± 50 rpm
Throttle cable adjustment
(Throttle valve fully opened)Between boot end face and inner cable stopper
0 − 1 mm (0 − 0.04 in.)
Drive plate runoutMax.
Torque converter runoutMax.
Torque converter installation distance 3R−FE
5VZ−FE0.20 mm (0.0079 in.)
0.30 mm (0.0118 in.)
More than 31.75 mm (1.2500 in.)
More than 17.95 mm (0.7067 in.)
Speedometer driven gear oil seal drive in depth 3RZ−FE
5VZ−FE20 mm (0.79 in.)
20 mm (0.79 in.)
Lock−up point
(3RZ−FE / A340E)
D position
(Throttle valve opening 5%) Lock−up ON
Lock−up OFF
(5VZ−FE / A340E)
D position
(Throttle valve opening 5%) Lock−up ON
Lock−up OFF
(5VZ−FE / A340F)
(Throttle valve opening 5%) Lock−up ON
Lock−up OFF
83 − 88 km/h (52 − 55 mph)
70 − 75 km/h (44 − 47 mph)
79 − 84 km/h (49 − 52 mph)
72 − 77 km/h (45 − 48 mph)
75 − 80 km/h (47 − 50 mph)
68 − 73 km/h (42 − 45 mph)

Downloaded from www.Manualslib.com manuals search engine SS08A−03
− SERVICE SPECIFICATIONSAUTOMATIC TRANSMISSION
SS−51
1996 TOYOTA T100 (RM449U)
TORQUE SPECIFICATION
Part tightenedN·mkgf·cmft·lbf
Valve body x Transmission case101007
Oil strainer x Valve body (A340E)5.45548 in.·lbf
Oil strainer case x Valve body (A340F)101007
Oil strainer x Valve body (A340F)6.97061 in.·lbf
Oil pan7.47565 in.·lbf
Drain plug2020515
Parking lock pawl bracket x Transmission case7.47565 in.·lbf
Extension housing x Transmission case (A340E)3637027
Extension housing x Rear mounting insulator2525018
Rear support member x Rear mounting insulator (A340F)1818013
Rear support member x Body (A340F)9597070
Rear mounting insulator x Rear mounting bracket (A340E)1818013
Rear mounting bracket x Frame (A340E)5859042
Propeller shaft x Rear differential (A340E)7475054
Front propeller shaft x Front differential (A340F)7475054
Front propeller shaft x Transfer (A340F)7475054
Rear propeller shaft x Transfer (A340F)7475054
Rear propeller shaft x Rear differential (A340F)7475054
Center support bearing x Body3637027
Drive plate x Crankshaft8385061
Torque converter clutch x Drive plate4142030
Stiffener plate x Engine (A340F)3738027
Stiffener plate x Transmission3738027
Front exhaust pipe x Exhaust manifold6263046
Front exhaust pipe x TWC4849035
Rear support member x Dynamic damper6162044
Oil cooler pipe3435025
Transmission x Engine7173053
Rear end plate x Transmission3738027
Rear support member x Transfer under cover2930021
Cross shaft x Frame2829021
Cross shaft x Transmission131309
Cross shaft x No.1 gear shifting rod131309
Exhaust pipe clamp(3RZ−FE)1919514
Exhaust pipe support bracket x Transmission (3RZ−FE)7173053
Exhaust pipe support bracket x Transmission (5VZ−FE)4445033
Exhaust pipe support bracket x Exhaust pipe (5VZ−FE)4445033
Park/neutral position switch (Nut)3.94035 in.·lbf
Park/neutral position switch (Bolt)131309
No.2 vehicle speed sensor5.45548 in.·lbf
Speedometer driven gear sleeve x Locking plate1616012
ATF temperature sensor x Transmission1515011
Shift lever assembly x Steering column assembly2930022

Downloaded from www.Manualslib.com manuals search engine SS090−02
− SERVICE SPECIFICATIONSTRANSFER
SS−55
1996 TOYOTA T100 (RM449U)
TORQUE SPECIFICATION
Part tightenedN·mkgf·cmft·lbf
Transfer x Dynamic damper3738027
Transfer adaptor x Transfer3738027
Engine rear mounting2526019
Indicator switch3738027
L4 position switch3738027
Transfer assembly x Transmission3738027
Front retainer1111 58
Control retainer or upper cover1818513
Companion flange lock nut11 81,20087
Extension housing1111 58
Front case x Rear case3738027
Straight screw plug for shift fork shaft1919014
Separator with oil strainer1818513
Oil pump body x Front case1111 58
Straight screw plug for ring gear1919014
Straight screw plug for oil pump body2930021
Oil pump plate x Oil pump body7.47565 in.·lbf

Downloaded from www.Manualslib.com manuals search engine SS07Z−04
− SERVICE SPECIFICATIONSPROPELLER SHAFT
SS−57
1996 TOYOTA T100 (RM449U)
TORQUE SPECIFICATION
Part tightenedN·mkgf·cmft·lbf
Propeller shaft x Differential 2WD7475054
Intermediate shaft x Propeller shaft 2WD7475054
Front propeller shaft x Front differential 4WD7475054
Front propeller shaft x Transfer 4WD7475054
Rear propeller shaft x Rear differential 4WD7678056
Rear propeller shaft x Transfer 4WD7678056
Intermediate shaft x Propeller shaft 4WD7678056
Center support bearing x Body3637027
Intermediate shaft x Center support bearing x Joint flange
1st1811,850134
Loosen nut
2WD (TMC−made) and 4WD 2nd6970051
2WD (DANA−made) 2nd8183060
Front propeller shaft No.2 dust cover set bolts1717513
Front propeller shaft No.2 dust cover set nuts1313510
Front propeller shaft dust cover bracket x Bracket2323017
Front propeller shaft dust cover bracket x Transfer3637027

Downloaded from www.Manualslib.com manuals search engine SS−62
− SERVICE SPECIFICATIONSSUSPENSION AND AXLE
236 Author: Date:
1996 TOYOTA T100 (RM449U) Wheel alignment
(Non−loaded
vehicle condition)
(4WD)
Camber STD cab
Extra cab
Left−right error0°35’ ± 45’ (0.59° ± 0.75°)
0°40’ ± 45’ (0.66° ± 0.75°)
45’ (0.75°) or less
Caster STD cab
Extra cab
Left−right error0°59’ ± 45’ (0.98° ± 0.75°)
1°10’ ± 45’ (1.17° ± 0.75°)
45’ (0.75°) or less
Steering axis inclination
Left−right error12°00’ ± 45’ (12° ± 0.75°)
45’ (0.75°) or less
To e−in (Total)STD cab
Extra cab (P235/75R15)
Extra cab (31x10.5R15)0°12’ ± 12’ (0.2° ± 0.2°, 2.7 ± 2 mm, 0.11 ± 0.08 in.)
0°08’ ± 12’ (0.14° ± 0.2°, 1.9 ± 2 mm, 0.07 ± 0.08 in.)
0°08’ ± 12’ (0.14° ± 0.2°, 2.0 ± 2 mm, 0.08 ± 0.08 in.)
Wheel angle
STD cab Inside wheel
Outside wheel
Extra cab Inside wheel
Outside wheel
32°45’ ± 2° (32.75° ± 2°)
30°31’ (30.52°)
33°07’ ± 2° (33.12° ± 2°)
30°31’ (30.52°)
Front axle (2WD)
Axle hub axial playMaximum0.05 mm (0.0020 in.)
Axle hub preload (at starting)Friction force plus
5.0 − 14.0 N (0.5 − 1.4 kgf, 1.1 − 3.1 in.)
Front axle (4WD)Axle hub preload (at starting)25 − 53 N (2.6 − 5.4 kgf, 5.7 − 11.9 lbf)
Front drive shaft thrust clearanceStandard0.1 − 0.5 mm (0.0039 − 0.0197 in.)
Front drive shaft
(4WD)Drive shaft length481.2 − 491.2 mm (18.945 − 19.339 in.)
Front suspension
(2WD)Upper ball joint turning torque2.0 − 3.9 N·m (20 − 40 kgf·cm, 17 − 34 in.·lbf)
Lower ball joint turning torque2.0 − 7.0 N·m (20 − 70 kgf·cm, 17 − 61 in.·lbf)
Front suspension
(4WD)Upper ball joint turning torque0.5 − 2.4 N·m (5 − 25 kgf·cm, 4 − 22 in.·lbf)
Lower ball joint turning torque2.0 − 3.9 N·m (20 − 40 kgf·cm, 17 − 34 in.·lbf)
Rear axleShaft runoutMaximum2.0 mm (0.079 in.)
Flange runoutMaximum0.1 mm (0.004 in.)
Front differential
(4WD)
Companion flange vertical runoutMaximum0.10 mm (0.0039 in.)
Companion flange lateral runout Maximum0.10 mm (0.0039 in.)
Drive pinion bearing preload (at starting)
New bearing
Reused bearing
1.2 − 1.9 N·m (12 − 19 kgf·cm, 10.4 − 16.5 in.·lbf)
0.6 − 1.0 N·m (6 − 10 kgf·cm, 5.2 − 8.7 in.·lbf)
Total preload (at starting)In addition to drive pinion preload
0.4 − 0.6 N·m (4 − 6 kgf·cm, 3.5 − 5.2 in.·lbf)
Pinion gear to side gear backlash0.05 − 0.20 mm (0.0020 − 0.0079 in.)
Drive pinion to ring gear backlash0.13 − 0.18 mm (0.0051 − 0.0070 in.)
Ring gear runoutMaximum0.07 mm (0.0028 in.)
Rear oil seal drive in depth1.5 mm (0.059 in.)
Side gear shaft tube LH side oil seal drive in depth2.5 mm (0.098 in.)
A.D.D. sleeve fork to clutch sleeve clearance0.35 mm (0.0138 in.)
Differential bearing press in depth2.0 mm (0.079 in.)

Downloaded from www.Manualslib.com manuals search engine SS083−02
− SERVICE SPECIFICATIONSSUSPENSION AND AXLE
SS−67
1996 TOYOTA T100 (RM449U)
TORQUE SPECIFICATION
Part tightenedN·mkgf·cmft·lbf
Front (2WD)
Tie rod end lock nut5657041
Steering knuckle x Upper ball joint1081,10080
Steering knuckle x Lower ball joint1421,450105
Steering knuckle x Brake caliper1081,10080
Steering knuckle x Steering knuckle arm1831,870135
Dust cover x Steering knuckle1919514
Disc x Axle hub6465047
Upper suspension arm x Upper ball joint3132023
Lower suspension arm x Lower ball joint7576055
Torque arm x Lower suspension arm4950036
Shock absorber x Frame2525018
Lower suspension arm x Shock absorber1818513
Lower suspension arm x Stabilizer bar131309
Lower suspension arm shaft nut2062,100152
Upper suspension arm shaft x Frame9698071
Upper suspension arm shaft x Upper suspension arm1261,28093
Lower ball joint x Strut bar7576055
Strut bar x Frame1231,25090
Stabilizer bar link set nut131309
Stabilizer bar bracket x Frame3030622
Hub nut1031,05076
ABS speed sensor x Steering knuckle8.08271 in.·lbf
ABS Speed sensor wire harness x Upper suspension arm5.05144 in.·lbf
Front (4WD)
Knuckle stopper bolt lock nut4748035
Tie rod clamp bolt2222516
Steering knuckle x Upper ball joint1421,450105
Steering knuckle x Lower ball joint5859043
Steering knuckle x Brake caliper1231,25090
Flange x Axle hub3131523
Flange x Front drive shaft1818513
Axle hub bearing lock nut4748035
Oil seal x Dust cover1818513
Upper suspension arm x Upper ball joint3334025
Lower suspension arm x Lower ball joint1421,450105
Steering knuckle arm x Steering knuckle1831,870135
Upper suspension arm x Torque arm8789064
Upper suspension arm shaft lock nut2262,300166
Shock absorber x Frame2525018
Lower suspension arm x Shock absorber1371,400101
Lower suspension arm x Stabilizer bar2526019
Stabilizer bar bracket x Frame2930022

Downloaded from www.Manualslib.com manuals search engine SS085−01
SS−70
− SERVICE SPECIFICATIONSBRAKE
1996 TOYOTA T100 (RM449U)
TORQUE SPECIFICATION
Part tightenedN·mkgf·cmft·lbf
Master cylinder x Piston stopper bolt101007
Master cylinder x Reservoir1.717.515.2 in.·lbf
Master cylinder x Brake booster131309
Brake line union nut1515511
Brake booster clevis lock nut2526019
Brake booster x Pedal bracket131309
Front disc brake caliper installation bolt 2WD 1.0 ton3940029
2WD 0.5 ton3637027
4WD1231,25090
Bleeder plug1111 08
Front disc brake torque plate x Steering knuckle 2WD1081,10080
Front disc x Front axle hub6465047
Front disc brake caliper x Flexible hose1515511
Rear drum brake wheel cylinder x Backing plate101007
Parking brake bellcrank bracket x Backing plate131309
LSP & BV installation nut131309
LSP & BV x Load Sensing Spring Assembly1818513
Load Sensing Spring Assembly x Shackle No.11818513
Shackle No.1 x Shackle No.22525018
Shackle No.2 x Shackle Bracket131309
LSP & BV x Frame2930011
ABS actuator x ABS actuator bracket5.45548 in.·lbf
ABS actuator bracket x Body1919514
Speed sensor installation bolt8.08271 in.·lbf
Front speed sensor wire harness clamp5.05144 in.·lbf
Rear speed sensor wire harness clamp131309

Downloaded from www.Manualslib.com manuals search engine SS08W−01
− SERVICE SPECIFICATIONSSTEERING
SS−71
245 Author: Date:
1996 TOYOTA T100 (RM449U)
STEERING
SERVICE DATA
ON−VEHICLE INSPECTION
Steering wheel freeplayMaximum30 mm (1.18 in.)
3RZ−FE:
Drive belt tension New belt135−185 lbf
Drive belt tension Used belt80−120 lbf
Oil level rise MaximumBelow 5 mm (0.20 in.)
5VZ−FE:
Drive belt tension New belt135−180 lbf
Drive belt tension Used belt85−120 lbf
Oil level rise MaximumBelow 5 mm (0.20 in.)
3RZ−FE and 5VZ−FE (2WD):
Oil pressure at idle speed with valve closedMinimum7,845 kPa (80 kgf/cm2, 1,138 psi)
5VZ−FE (4WD):
Oil pressure at idle speed with valve closedMinimum8,336 kPa (85 kgf/cm2, 1,209 psi)
Steering effort at idle speedMaximum8.3 N·m (85 kgf·cm, 73 in.·lbf)
TILT STEERING COLUMN
Pawl stopper
1 or A12.68 − 12.74 mm (0.4992 − 0.5016 in.)
2 or B12.61 − 12.67 mm (0.4965 − 0.4988 in.)
3 or C12.54 − 12.60 mm (0.4937 − 0.4961 in.)
4 or D12.47 − 12.53 mm (0.4909 − 0.4933 in.)
5 or E12.40 − 12.46 mm (0.4882 − 0.4906 in.)
6 or F12.33 − 12.39 mm (0.4854 − 0.4878 in.)
7 or G12.26 − 12.32 mm (0.4827 − 0.4850 in.)
PS VANE PUMP
3RZ−FE and 5VZ−FE:
Pump shaft and front housing bushing oil clearance STD0.03−0.05 mm (0.0012−0.0020 in.)
Pump shaft and front housing bushing oil clearanceMaximum0.07 mm (0.0028 in.)
Vane plate heightMinimum8.6 mm (0.339 in.)
Vane plate thicknessMinimum1.397 mm (0.0550 in.)
Vane plate lengthMinimum14.991 mm (0.5902 in.)
Vane plate and pump rotor groove clearanceMaximum0.035 mm (0.0014 in.)
Vane plate length Pump rotor and cam ring mark
None14.999−15.001 mm (0.59051−0.59059 in.)
114.997−14.999 mm (0.59043−0.59051 in.)
214.995−14.997 mm (0.59035−0.59043 in.)
314.993−14.995 mm (0.59027−0.59035 in.)
414.991−14.993 mm (0.59020−0.59027 in.)
Flow control valve spring lengthMinimum32.3 mm (1.272 in.)
Pump rotating torqueMaximum0.25 N·m (2.5 kgf·cm, 2.2 in.·lbf) or less
PS GEAR
2WD:
Steering rack runoutMaximum0.3 mm (0.0118 in.)