1996 TOYOTA T100 engine

Downloaded from www.Manualslib.com manuals search engine BO0E7−01
− BODYWHEEL ARCH MOULDING
BO−17
1996 TOYOTA T100 (RM449U)
REMOVAL
1. REMOVE FRONT WHEEL ARCH MOULDING
HINT:
Tape a screwdriver tip before use.
(a) Remove the 6 screws and a clip.
(b) Using the screwdriver, pry up the wheel arch moulding, and remove it.
2. REMOVE REAR WHEEL ARCH MOULDING
HINT:
Tape a screwdriver tip before use.
(a) Remove the screw and 5 clips.
(b) Using the screwdriver, pry up the wheel arch moulding, and remove it.

Downloaded from www.Manualslib.com manuals search engine BO0E8−01
BO−18
− BODYWHEEL ARCH MOULDING
1996 TOYOTA T100 (RM449U)
INSTALLATION
Installation is in the reverse order of removal (See page BO−17).

Downloaded from www.Manualslib.com manuals search engine BO0E9−02
N05945
Windshield Upper Moulding
Inner Rear View Mirror
Windshield Outside MouldingWindshield Glass
Front Pillar Garnish
Cowl LouverAssist Grip
Weatherstrip
Non−reusable partWiper ArmDam Sun Visor
Holder
 Holder

N·m (kgf·cm,ft·lbf) : Specigied torque
20 (204, 15)
− BODYWINDSHIELD
BO−19
1903 Author: Date:
1996 TOYOTA T100 (RM449U)
WINDSHIELD
COMPONENTS

Downloaded from www.Manualslib.com manuals search engine BO0EA−02
N05942
N12567
BO5232
BO1689
BO−20
− BODYWINDSHIELD
1996 TOYOTA T100 (RM449U)
REMOVAL
1. REMOVE INNER REAR VIEW MIRROR
2. REMOVE SUN VISORS AND HOLDERS
3. REMOVE ASSIST GRIPS
4. REMOVE FRONT PILLAR GARNISHES
5. REMOVE WIPER ARMS
6. REMOVE COWL LOUVER
7. REMOVE WEATHERSTRIP
8. REMOVE WINDSHIELD OUTSIDE MOULDING
Remove the 4 screws and the moulding.
9. REMOVE WINDSHIELD OUTSIDE MOULDING
Using a knife, cut off the moulding, as shown.
NOTICE:
Do not damage the body with the knife.
10. REMOVE WINDSHIELD GLASS
(a) Push piano wire through between the body and glass
from the interior.
(b) Tie both wire ends to a wooden block or similar object.
HINT:
Apply adhesive tape to the outer surface to keep the surface
from being scratched.
NOTICE:
When separating the glass, take care not to damage the
paint and interior and exterior ornaments. To prevent
scratching the safety pad when removing the windshield,
place a plastic sheet between the piano wire and safety
pad.
(c) Cut the adhesive by pulling the piano wire around it.
(d) Remove the glass.
NOTICE:
Leave as much of the adhesive on the body as possible
when cutting off the glass.

Downloaded from www.Manualslib.com manuals search engine BO3E4−02
N21214
Adhesive
BO5231
N06557
Spacer
BO4421
N06558
7 mm (0.28 in.)
− BODYWINDSHIELD
BO−21
1996 TOYOTA T100 (RM449U)
INSTALLATION
1. CLEAN AND SHAPE CONTACT SURFACE OF BODY
(a) Using a knife, cut away any rough areas on the body.
HINT:
Leave as much of the adhesive on the body as possible.
(b) Clean the cutting surface of the adhesive with a piece of
shop rag saturated in cleaner.
HINT:
Even if all the adhesive has been removed, clean the body.
2. CLEAN REMOVED GLASS
(a) Using a scraper, remove the adhesive sticking to the
glass.
(b) Clean the glass with cleaner.
NOTICE:
Do not touch the glass after cleaning it.
3. POSITION GLASS
(a) Place the glass in correct position.
(b) Check that all contacting parts of the glass rim are perfect-
ly even and do not make contact with the spacers.
(c) Place reference marks between the glass and body.
(d) Remove the glass.
4. CLEAN CONTACT SURFACE OF GLASS
Using a cleaner, clean the contact surface black−colored area
around the entire glass rim.
NOTICE:
Do not touch the glass face after cleaning it.
5. INSTALL DAM
Install the dam with double − stick tape as shown in the illustra-
tion.
NOTICE:
Do not touch the glass face after cleaning it.

Downloaded from www.Manualslib.com manuals search engine N00141
Primer M
Adhesive
Primer M Primer M
N06556
Primer G
BO4422
N06484
15 mm
(0.59 in.)
7 mm
(0.28 in.) BO−22
− BODYWINDSHIELD
1996 TOYOTA T100 (RM449U)
6. COAT CONTACT SURFACE OF BODY WITH PRIMER
”M”
Using a brush, coat the contact surface on the body with Primer
M.
NOTICE:
Let the primer coating dry for 3 minutes or more.
Do not coat Primer M to the adhesive.
Do not keep any of the opened Primer M for later use.
7. COAT CONTACT SURFACE OF GLASS WITH PRIMER
”G”
(a) Using a brush or sponge, coat the edge of the glass and
the contact surface with Primer G.
(b) Before the primer dries, wipe it off with a clean shop rag.
NOTICE:
Let the primer coating dry for 3 minutes or more.
Do not keep any of the opened Primer G for later use.
8. MIX ADHESIVE COATING
NOTICE:
Be sure that installation of the moulding is finished
within usable time.
The mixture should be made in 5 minutes or less.
(a) Throughly clean the glass plate and putty spatula with sol-
vent.
(b) Thoroughly mix 500 g (17.64 oz.) of the main agent and
75 g (2.65 oz.) of the hardening agent on a glass plate or
like object with a putty spatula.
9. APPLY ADHESIVE
(a) Cut off the tip of the cartridge nozzle.
Part No. 08850−00801 or equivalent
HINT:
After cutting off the tip, use all adhesive within the time de-
scribed in the chart below.
TemperatureTackfree time
35°C (95 °F)15 minutes
20°C (68 °F)100 minutes
5°C (41 °F)8 hours
(b) Load the cartridge into the sealer gun.
(c) Coat the glass with adhesive, as shown.

Downloaded from www.Manualslib.com manuals search engine BO2821
BO3986
BO3671
Adhesive
Adhesive
N12568
− BODYWINDSHIELD
BO−23
1996 TOYOTA T100 (RM449U)
10. INSTALL GLASS
(a) Position the glass so that the reference marks are lined
up, and press in gently along the rim.
(b) Using a spatula, apply adhesive on the glass rim.
(c) Use a scraper to remove any excess or protruding adhe-
sive.
(d) Fasten glass securely until the adhesive sets.
NOTICE:
Take care not to drive the vehicle during the time described
in the chart below.
TemperatureMinimum time prior to drive of the vehicle
35°C (95 °F)1.5 hours
20°C (68 °F)5 hours
5°C (41 °F)24 hours
11. INSPECT FOR LEAKS AND REPAIR
(a) Perform a leak test after the hardening time has elapsed.
(b) Seal any leak with sealant.
Part No. 08833−00030 or equivalent
12. APPLY ADHESIVE AT MOULDING INSTALLATION
AREA
Coat the glass with adhesive at the mouldig installation area.
Part No. 08833−00030 or equivalent
13. INSTALL WINDSHIELD UPPER MOULDING
Place the moulding onto the body and tap it by hand.
14. INSTALL WINDSHIELD OUTSIDE MOULDING
15. INSTALL WEATHERSTRIP
16. INSTALL COWL LOUVER
17. INSTALL WIPER ARMS
Torque: 20 N·m (204 kgf·cm, 15 ft·lbf)
18. INSTALL FRONT PILLAR GARNISHES
19. INSTALL ASSIST GRIPS
20. INSTALL SUN VISORS AND HOLDERS

Downloaded from www.Manualslib.com manuals search engine BO−24
− BODYWINDSHIELD
1996 TOYOTA T100 (RM449U)
21. INSTALL INNER REAR VIEW MIRROR