1996 TOYOTA LAND CRUISER Ignition switch

A00168
ON
EGR Gas Temp.
Sensor ECM
19 9
1
2
BE6653
FI7055 THG
E2
E4
E5 5V
−
DIAGNOSTICS ENGINE
DI−71
1996 LAND CRUISER (RM451U)
INSPECTION PROCEDURE
TOYOTA hand −held tester
1 Connect the TOYOTA hand −held tester and read value of EGR gas temp. value.
PREPARATION:
(a) Remove the fuse cover on the instrument panel.
(b) Connect the TOYOTA hand−held tester to the DLC3.
(c) Turn ignition switch ON and push the TOYOTA hand −held tester main switch ON.
CHECK:
Read EGR gas temp. on the TOYOTA hand−held tester.
OK:
EGR gas temp.: 10° C (50°F) or more
HINT:
If there is and open circuit, the TOYOTA hand−held tester indicates 3.1 °C (37.6° F).
OK Go to step 4.
NG
2 Check for open in harness or ECM.
PREPARATION:
(a) Disconnect the EGR gas temp. sensor connector.
(b) Connect sensor wire harness terminals together.
(c) Turn ignition switch ON.
CHECK:
Read EGR gas temp. on the TOYOTA hand−held tester.
OK:
EGR gas temp.: Approx. 157.5° C (315.5°F)
OK Confirm good connection at sensor. If OK, replace EGR gas temp. sensor.
NG
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

A00170
System : ON
System : OFF Air
GE
Air GE
P22963
P22964
−
DIAGNOSTICS ENGINE
DI−73
1996 LAND CRUISER (RM451U)
5 Check the VSV for EGR.
PREPARATION:
(a) Remove the fuse cover on the instrument panel.
(b) Connect the TOYOTA hand−held tester to the DLC3.
(c) Turn ignition switch ON and TOYOTA hand −held tester
main switch ON.
(d) Select the ACTIVE TEST mode on the TOYOTA hand −
held tester.
CHECK:
Check operation of VSV, when it is operated by the TOYOTA
hand −held tester.
OK:
EGR system is ON:
Air does not flow from pipe G to pipe E.
EGR system is OFF:
Air from pipe G is flowing out through pipe E.
OK Go to step 7.
NG
6 Check operation of the VSV for EGR (See page SF−60).
NG Replace VSV for EGR.
OK
Check for open in harness and connector be-
tween VSV and ECM (See page IN−28).
7 Check EGR vacuum modulator (See page EC−11 ).
NG Repair or replace.
OK
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

DI−74
−
DIAGNOSTICS ENGINE
1996 LAND CRUISER (RM451U)
8 Check EGR valve (See page EC−11).
NG Repair or replace.
OK
9 Check value of EGR gas temp. sensor.
PREPARATION:
(a) Remove the fuse cover on the instrument panel.
(b) Connect the TOYOTA hand−held tester to the DLC3.
(c) Turn ignition switch ON and TOYOTA hand −held tester main switch ON.
(d) Select the ACTIVE TEST mode on the TOYOTA hand−held tester. (EGR system ON)
(e) Race the engine at 4,000 rpm for 3 mins.
CHECK:
Measure the EGR gas temp. while racing engine at 4,000 rpm.
OK:
EGR gas temp. after 3 mins.: 140° C (284°F) or more
NG Replace EGR gas temp. sensor.
OK
Check and replace ECM (See page IN−28 ).
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

P24665
A00171
ON(−)(+)
BE6653
P22896
P24666
−
DIAGNOSTICS ENGINE
DI−75
1996 LAND CRUISER (RM451U)
OBD II scan tool (excluding TOYOTA hand −held tester)
1 Check resistance of EGR gas temp. sensor.
PREPARATION:
Disconnect EGR gas temp. sensor connector.
CHECK:
Measure resistance between terminals of EGR gas temp. sen-
sor connector.
OK:
Resistance: 600 k Ω or less
HINT:
If there is open circuit, ohmmeter indicates 720 k Ω or more.
NG Check and replace EGR gas temp. sensor (See page SF−63 ).
OK
2 Check for open in harness or ECM.
PREPARATION:
(a) Disconnect EGR gas temp. sensor connector.
(b) Turn ignition switch ON.
CHECK:
Measure voltage between terminals of EGR gas temp. sensor
wire harness side connector.
OK:
Voltage: 4.5 − 5.5 V
OK Go to step 4.
NG
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

A00172
ON
THG E2 (+)(−)
BE6653
P24667
DI−76
−
DIAGNOSTICS ENGINE
1996 LAND CRUISER (RM451U)
3 Check for open in harness or ECM.
PREPARATION:
(a) Remove instrument panel speaker No.1 panel (See page
SF−65 ).
(b) Turn ignition switch ON.
CHECK:
Measure voltage between terminals of THG and E2 of ECM
connector.
HINT:
EGR gas temp. sensor connector is disconnected.
OK:
Voltage: 4.5 − 5.5 V
OK Open in harness between terminals E2 or THG. Repair or replace harness.
NG
Confirm connection at ECM.
If OK, replace ECM (See page IN−28).
4 Check connection of vacuum hose, EGR hose (See page EC−11).
NG Repair or replace.
OK
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

A00173
ON
EGR ONOFF
(1) VSV is ON:
(2) VSV is OFF: Air
GE
Air GE
BE6653
P22905
P22963
P22964
−
DIAGNOSTICS ENGINE
DI−77
1996 LAND CRUISER (RM451U)
5 Check the VSV for EGR.
PREPARATION:
(a) Remove instrument panel speaker No.1 panel (See page
SF−65 ).
(b) Turn ignition switch ON.
CHECK:
Check VSV function.
(1) Connect between terminal EGR of ECM and bodyground (ON).
(2) Disconnect between terminal EGR of ECM and
body ground (OFF).
OK:
(1) VSV is ON:
Air does not flow from pipe G to pipe E.
(2) VSV is OFF:
Air from pipe G is flows out through pipe E.
OK Go to step 7.
NG
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

DI−80
−
DIAGNOSTICS ENGINE
1996 LAND CRUISER (RM451U)
DTC P0402 Exhaust Gas Recirculation Flow Excessive Detected
CIRCUIT DESCRIPTION
Refer to DTC P0401 (Exhaust Gas Recirculation Flow Insufficient Detected) on page DI−69.
DTC No.DTC Detecting ConditionTrouble Area
P0402
EGR gas temp. sensor value is high during EGR cut −off when
engine is cold (Race engine at about 4,000 rpm without load so
that vacuum is applied to port E)
(2 trip detection logic) EGR valve stuck open
 EGR VSV open malfunction
 Open in VSV circuit for EGR
 Short in EGR gas temp. sensor circuit
 ECM
EGR valve is always open (2 trip detection logic)
Refer to DTC P0401 (Exhaust Gas Recirculation Flow Insufficient Detected) for the System Check Driving
Pattern and Wiring Diagram.
INSPECTION PROCEDURE
TOYOTA hand −held tester
1 Connect the TOYOTA hand −held tester and read EGR gas temp. value.
PREPARATION:
(a) Remove the fuse cover on the instrument panel.
(b) Connect the TOYOTA hand−held tester to the DLC3.
(c) Turn ignition switch ON and push the TOYOTA hand −held tester main switch ON.
CHECK:
Read EGR gas temp. on the TOYOTA hand−held tester.
OK:
EGR gas temp.: 150° C (302°F) or less (Not immediately after driving)
HINT:
If there is a short circuit, the TOYOTA hand−held tester indicates Approx. 157.5°C (315.5°F).
OK Go to step 4.
NG
DI5PL−02
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

A00176
ONSPD
(+)
(−)
BE6653
P24668
AT7809
9 − 14 V
0
Turn the wheel
DI−88
−
DIAGNOSTICS ENGINE
1996 LAND CRUISER (RM451U)
INSPECTION PROCEDURE
1 Check operation of speedometer.
CHECK:
Drive the vehicle and check if the operation of the speedmeter in the co\
mbination meter is normal.
HINT:
The vehicle speed sensor is operating normally if the speedometer displa\
y is normal.
NG Check speedometer circuit (See page BE−2 ).
OK
2 Check voltage between terminal SPD of ECM connector and body ground.
PREPARATION:
(a) Remove instrument panel speaker No.1 panel (See page SF−65 ).
(b) Disconnect cruise control ECU connector.
(c) Shift the shift lever to neutral.
(d) Jack up a rear wheels on one side.
(e) Turn ignition switch ON.
CHECK:
Measure voltage between terminal SPD of ECM connector and
body ground when the wheel is turned slowly.
OK:
Voltage is generated intermittently.
NG Check and repair harness and connector between combination meter and ECM.
OK
Check and replace ECM (See page IN−28 ).
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010