1996 TOYOTA LAND CRUISER engine

SF0PO−09
Z02917
Ohmmeter
TEMPERATURE °C (° F)
RESISTANCE kΩ
Acceptable
−
SFI ENGINE COOLANT TEMPERATURE (ECT) SENSOR
SF−61
689
Author: Date:
1996 LAND CRUISER (RM451U)
ENGINE COOLANT
TEMPERATURE (ECT) SENSOR
INSPECTION
1. DRAIN ENGINE COOLANT
2. REMOVE ECT SENSOR
(a) Disconnect the ECT sensor connector.
(b) Using a 19 mm deep socket wrench, remove the ECT
sensor and gasket.
3. INSPECT ECT SENSOR
Using an ohmmeter, measure the resistance between the ter-
minals. Resistance: Refer to the chart graph
If the resistance is not as specified, replace the ECT sensor.
4. REINSTALL ECT SENSOR
(a) Using a 19 mm deep socket wrench, install the ECT sen- sor and gasket.
Torque: 24.5 N·m (250 kgf·cm, 17.5 ft·lbf)
(b) Connect the ECT sensor connector.
5. REFILL ENGINE COOLANT
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SF0Q0−07
−
SFI ENGINE CONTROL MODULE (ECM)
SF−65
693
Author: Date:
1996 LAND CRUISER (RM451U)
ENGINE CONTROL MODULE (ECM)
COMPONENTS
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SF0Q1−07
SF−66
−
SFI ENGINE CONTROL MODULE (ECM)
1996 LAND CRUISER (RM451U)
INSPECTION
1. REMOVE ECM
2. INSPECT ECM (See page DI−17 )
3. REINSTALL ECM
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SF0Q2−08
−
SFI FUEL CUT RPM
SF−67
695
Author: Date:
1996 LAND CRUISER (RM451U)
FUEL CUT RPM
INSPECTION
1. WARM UP ENGINE
Allow the engine to warm up to normal operating temperature.
2. CONNECT TOYOTA HAND −HELD TESTER OR OBD II
SCAN TOOL
(a) Remove the fuse cover on the instrument panel.
(b) Connect the TOYOTA hand−held tester or OBD II scan tool to the DLC3.
(c) Please refer to the TOYOTA hand−held tester or OBD II
scan tool operator’s manual for further details.
3. INSPECT FUEL CUTOFF PRM
(a) Increase the engine speed to at least 3,500 rpm.
(b) Use a sound scope to check for injector operating noise.
(c) Check that when the throttle lever is released, injector op-
eration noise stops momentarily and then resumes.
HINT:
Measure with the A/C OFF. Fuel return rpm: 1,200 rpm
4. DISCONNECT TOYOTA HAND −HELD TESTER OR
OBD II SCAN TOOL
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SR167−01
R07281
Normal
Abnormal
−
STEERING POWER STEERING FLUID
SR−3
1054
Author: Date:
1996 LAND CRUISER (RM451U)
POWER STEERING FLUID
BLEEDING
1. CHECK FLUID LEVEL (See page SR−4 )
2. JACK UP FRONT OF VEHICLE AND SUPPORT IT WITH STANDS
3. TURN STEERING WHEEL
With the engine stopped, turn the wheel slowly from lock to lock
several times.
4. LOWER VEHICLE
5. START ENGINE
Run the engine at idle for a few minutes.
6. TURN STEERING WHEEL
(a) With the engine idling, turn the wheel to left or right full lock and keep it there for 2 −3 seconds, then turn the
wheel to the opposite full lock and keep it there for 2 −3 se-
conds.
(b) Repeat (a) several times.
7. STOP ENGINE
8. CHECK FOR FOAMING OR EMULSIFICATION
If the system has to be bled twice specifically because of foam-
ing or emulsification, check for fluid leaks in the system.
9. CHECK FLUID LEVEL (See page SR−4)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SR166−01
R07281
Normal Abnormal
SR−4
−
STEERING POWER STEERING FLUID
1996 LAND CRUISER (RM451U)
INSPECTION
1. CHECK FLUID LEVEL
(a) Keep the vehicle level.
(b) With the engine stopped, check the fluid level in the oil reservoir.
If necessary, add fluid.
Fluid: ATF DEXRON® II or III
HINT:
Check that the fluid level is within the HOT LEVEL range on the
reservoir cap dipstick. If the fluid is cold, check that it is within
the COLD LEVEL range.
(c) Start the engine and run it at idle.
(d) Turn the steering wheel from lock to lock several times to
boost fluid temperature.
Fluid temperature: 80° C (176°F)
(e) Check for foaming or emulsification.
If there is foaming or emulsification, bleed power steering sys-
tem. (See page SR−3 ).
(f) With the engine idling, measure the fluid level in the oil reservoir.
(g) Stop the engine.
(h) Wait a few minutes and remeasure the fluid level in the oil reservoir.
Maximum fluid level rise: 5 mm (0.20 in.)
If a problem is found, bleed power steering system (See page
SR−3 ).
(i) Check the fluid level.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Z15498
PS GearClosed
SST PS Vane
Pump
Oil
Reservoir
−
STEERING POWER STEERING FLUID
SR−5
1996 LAND CRUISER (RM451U)
2. CHECK STEERING FLUID PRESSURE
(a) Disconnect the pressure feed tube from the PS vane
pump (See page SR−23).
(b) Connect SST over 2 new gaskets, as shown below. SST 09640 −10010 (09641 −01010, 09641 −01030,
09641 −01060)
NOTICE:
Check that the valve of the SST is in the open position.
(c) Bleed the power steering system (See page SR−3).
(d) Start the engine and run it at idle.
(e) Turn the steering wheel from lock to lock several times to
boost fluid temperature.
Fluid temperature: 80° C (176°F)
(f) With the engine idling, close the valve of the SST and ob-
serve the reading on the SST.
Minimum fluid pressure:
9,316kPa (95 kgf/cm
2, 1,351 psi)
NOTICE:
Do not keep the valve closed for more than 10 se-
conds.
Do not let the fluid temperature become too high.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Z15499
PS GearSSTPS Vane
Pump
Oil
Reservoir
Open
Z15500
PS Gear
SSTPS Vane
Pump
Oil
Reservoir
Open
Lock Position
SR−6
−
STEERING POWER STEERING FLUID
1996 LAND CRUISER (RM451U)
(g) With the engine idling, open the valve fully.
(h) Measure the fluid pressure at engine speeds of 1,000 rpm
and 3,000 rpm.
Difference fluid pressure:
490 kPa (5 kgf/cm
2, 71 psi) or less
NOTICE:
Do not turn the steering wheel.
(i) With the engine idling and valve fully opened, turn the steering wheel to full lock.
Minimum fluid pressure:
9,316 kPa (95 kgf/cm
2, 1,351 psi)
NOTICE:
Do not maintain lock position for more than 10 se-
conds.
Do not let the fluid temperature become too high.
(j) Disconnect the SST.
(k) Connect the pressure feed tube (See page SR−32).
(l) Bleed the power steering system (See page SR−3).
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010