1996 TOYOTA LAND CRUISER diff oil

SA1VE−01
Z15218
SST
R13239
Z06901
SST
Z06902
SST
−
SUSPENSION AND AXLE REAR DIFFERENTIAL FRONT OIL SEAL
SA−73
1996 LAND CRUISER (RM451U)
REPLACEMENT
1. DRAIN DIFFERENTIAL OIL
2. DISCONNECT REAR PROPELLER SHAFT
(See page PR−3 )
3. REMOVE COMPANION FLANGE
(a) Using a chisel and hammer, loosen the staked part of the
nut.
(b) Using SST to hold the flange, remove the nut and plate washer.
SST 09330−00021
(c) Using SST, remove the companion flange. SST 09950−30010 (09951 −03010, 09953−03010,
09954 −03010, 09955 −03030, 09956−03020)
4. REMOVE OIL SEAL AND OIL SLINGER
(a) Using SST, remove the oil seal. SST 09308−10010
(b) Remove the oil slinger.
5. REMOVE FRONT BEARING
Using SST, remove the front bearing from the drive pinion. SST 09556−22010
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SA2395
SST
Z06903
SST
Z06904
SST
R13238
SST
SA1966
SST
SA−74
−
SUSPENSION AND AXLE REAR DIFFERENTIAL FRONT OIL SEAL
1996 LAND CRUISER (RM451U)
6. REMOVE BEARING OUTER RACE
Using SST, remove the bearing outer race.
SST 09308−00010
NOTICE:
Do not scratch the taper surface of the outer race.
7. REMOVE BEARING SPACER
8. INSTALL NEW BEARING SPACER
9. INSTALL BEARING OUTER RACE
Using SST, install the bearing outer race. SST 09316−60011 (09316 −00011, 09316−00021)
10. INSTALL FRONT BEARING
11. INSTALL OIL SLINGER AND OIL SEAL
(a) Install the oil slinger.
(b) Using SST, install a new oil seal, as shown. SST 09214−76011
Oil seal drive in depth: 1.0 mm (0.039 in.)
(c) Apply MP grease to the oil seal lip.
12. INSTALL COMPANION FLANGE
(a) Using SST, install the companion flange on the drive pin- ion.
SST 09950−30010 (09951 −03010, 09953−03010,
09954 −03010, 09955 −03030, 09956−03020)
(b) Place the plate washer on the companion flange.
(c) Apply light coat of gear oil on threads of a new companion
flange nut.
(d) Using SST to hold the flange, torque the nut. SST 09330−00021
Torque: 245 N·m (2,500 kgf·cm, 181 ft·lbf)
13. ADJUST DRIVE PINION PRELOAD (See page SA−73 )
14. STAKE DRIVE PINION NUT
15. CONNECT REAR PROPELLER SHAFT (See page PR−5 )
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Z06905
Less than 5 mm
(10.20 in.)
−
SUSPENSION AND AXLE REAR DIFFERENTIAL FRONT OIL SEAL
SA−75
1996 LAND CRUISER (RM451U)
16. FILL DIFFERENTIAL WITH GEAR OIL
Torque: 49 N·m (500 kgf·cm, 39 ft·lbf)
Oil type: Hypoid gear oil API GL −5
Recommended oil viscosity:
Above −18°C (0° F) SAE 90
Below −18°C (0° F) SAE 80W−90 or 80W
Capacity:
3.25 liters (3.4 US qts, 2.9 Imp. qts)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SA24T−01
SA2310
−
SUSPENSION AND AXLE REAR DIFFERENTIAL CARRIER
SA−79
1996 LAND CRUISER (RM451U)
REMOVAL
1. w/ Differential lock:
SHIFT REAR DIFFERENTIAL TO LOCK
(a) Turn the ignition switch to the ON position.
(b) Keep the center differential lock condition.
(c) Turn the differential lock control switch to the RR or FR/ RR position and lock the rear differential.
HINT:
Rotating the tires, check they are in the differential lock condi-
tion.
(d) Disconnect the cable from the negative terminal of the battery.
2. DRAIN DIFFERENTIAL OIL
3. REMOVE REAR AXLE SHAFTS (See page SA−63 )
4. DISCONNECT PROPELLER SHAFT (See page PR−3 )
5. REMOVE DIFFERENTIAL CARRIER ASSEMBLY
(a) Remove the 10 nuts, washers and differential carrier as- sembly.
NOTICE:
Be careful not to damage the installation surface. Torque: 73 N·m (740 kgf·cm, 54 ft·lbf)
(b) Remove the gasket.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

R13166
SST
SA2348
SST
Z00641
SST
SSTSST
SA−82
−
SUSPENSION AND AXLE REAR DIFFERENTIAL CARRIER
1996 LAND CRUISER (RM451U)
(c) Using SST, remove the companion flange.
SST 09950 −30010 (09951 −03010, 09953 −03010,
09954 −03010, 09955 −03030, 09956−03020)
12. REMOVE OIL SEAL AND OIL SLINGER
(a) Using SST, remove the oil seal from the dif ferential carrier.
SST 09308−10010
(b) Remove the oil slinger.
13. REMOVE FRONT BEARING
Using SST, remove the front bearing from the drive pinion. SST 09556−22010
If the front bearing is damaged or worn, replace the bearing.
14. w/o DIFFERENTIAL LOCK: REMOVE DIFFERENTIAL CASE ASSEMBLY
(a) Place matchmarks on the bearing cap and dif ferential car-
rier.
(b) Remove the 2 adjusting nut locks.
HINT:
Tag the disassembled parts to show the location for reassemb-
ly.
(c) Remove the 2 bearing caps and adjusting nuts.
(d) Remove the differential case with the bearing outer races
from the carrier.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SA0510
SA1VJ−04
Z06893
−
SUSPENSION AND AXLE REAR DIFFERENTIAL CARRIER
SA−87
1996 LAND CRUISER (RM451U)
REASSEMBLY
1. w/o DIFFERENTIAL LOCK:
ASSEMBLE DIFFERENTIAL CASE
(a) Apply all of the sliding and rotating surfaces with gear oil.
(b) Install the 2 thrust washers and side gears. Using the table below, select the thrust washers which will
ensure that the backlash is within the specification.
Try to select washers of the same size for both sides.
Backlash: 0.02 − 0.20 mm (0.0008−0.0079 in.)
Thrust washer thickness
Thickness mm (in.)Thickness mm (in.)
1.60 (0.063)1.90 (0.075)
1.75 (0.069)2.05 (0.081)
(c) Install the side gears with the side gear thrust washers,
pinion gears, pinion gear thrust washers and pinion shaft.
HINT:
Align the hole for the pinion shaft and differential case hole.
(d) Using a dial indicator, measure the side gear backlash with holding the one pinion gear toward the case.
Backlash: 0.02 − 0.20 mm (0.0008 − 0.0079 in.)
If the backlash is not within the specification, install a thrust
washer of different thickness.
(e) Install the pinion shaft pin and washer.
Torque: 27 N·m (275 kgf·cm, 20 ft·lbf)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SA0510
R08274
R08276
R13246
SA−88
−
SUSPENSION AND AXLE REAR DIFFERENTIAL CARRIER
1996 LAND CRUISER (RM451U)
2. w/ DIFFERENTIAL LOCK:
MEASURE SIDE GEAR BACKLASH
(a) Apply all of the sliding and rotating surfaces with gear oil.
(b) Install the thrust washer to the side gear.
(c) Install the thrust washer to the pinion gear.
(d) Install the side gear into the case.
(e) Install the holder into the case.
(f) Install the 4 pinion gears with the thrust washers.
(g) Align the pinion shaft hole and case pinion shaft pin hole,
and install the pinion shaft.
(h) Install the side gear to the cover.
(i) Align the matchmarks and install the case and cover.
(j) Using a torx socket wrench, torque the 5 bolts and 3 pin-
ion shaft pins.
Torque: 58 N·m (590 kgf·cm, 43 ft·lbf)
(k) Using a dial indicator, with holding the side gear and mea- sure the backlash.
Backlash: 0.02 − 0.20 mm (0.0008 − 0.0079 in.)
HINT:
Measure at all 4 locations.
If the backlash is not within the specification, install the thrust
washer of a different thickness. Thrust washer thickness
Thickness mm (in.)Thickness mm (in.)
1.60 (0.063)1.90 (0.075)
1.75 (0.069)2.05 (0.081)
(l) After measuring backlash, remove the 5 set bolts and 3pinion shaft pins.
3. w/ DIFFERENTIAL LOCK: ASSEMBLE DIFFERENTIAL CASE
(a) Clean the thread of the bolts, pinion shaft pins, case and
cover with the white gasoline.
(b) Coat the threads of the bolts and pinion shaft pins with adhesive.
Adhesive: Part No. 08833 −00070, THREE BOND 1324
or equivalent
(c) Align the matchmarks, install the case and cover.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SA1143
Boiling Water
−
SUSPENSION AND AXLE REAR DIFFERENTIAL CARRIER
SA−89
1996 LAND CRUISER (RM451U)
(d) Using a torx socket wrench, torque the 5 bolts and 3 pin-
ion shaft pins.
Torque: 58 N·m (590 kgf·cm, 43 ft·lbf)
4. INSTALL SIDE BEARINGS
(a) w/o Differential lock: Using SST and a press, install the 2 side bearings on the
differential case.
SST 09315−00022, 09550 −10012 (09558−10010)
(b) w/ Differential lock:
Using SST and a press, install the 2 side bearings on the
differential case.
SST 09550−60010, 09550 −10012 (09558−10010)
5. INSTALL RING GEAR ON DIFFERENTIAL CASE
(a) Clean the contact surfaces of the differential case and ring gear.
(b) Heat the ring gear to about 100° C (212°F) in boiling wa-
ter.
(c) Carefully remove the ring gear from the boiling water.
(d) After the moisture on the ring gear has completely evapo-
rated, quickly install the ring gear to the differential case.
(e) Align the matchmarks on the ring gear and differential case.
(f) Temporarily install the set bolts and nuts so that the bolt
holes in the ring gear and differential case are not misa-
ligned.
NOTICE:
Install the bolts so that the tapered part of the bolt is on the
ring gear side. The ring gear set nuts should not tighten un-
til the ring gear has cooled sufficiently.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010