1996 TOYOTA LAND CRUISER diff oil

TR0CM−01
Q07105
Q07124
FIPG
TR−4
−
TRANSFER TRANSFER ASSEMBLY
1996 LAND CRUISER (RM451U)
DISASSEMBLY
1. REMOVE BREATHER HOSE
2. REMOVE DYNAMIC DAMPER
Remove the 2 bolts and dynamic damper.
HINT:
At the time of reassembly, apply adhesive to the bolt threads. Adhesive: Part No.08833 −00070, THREE BOND 1324
or equivalent
Torque: 37 N·m (380 kgf·cm, 27 ft·lbf)
3. REMOVE MOTOR ACTUATOR
Remove the 4 bolts and motor actuator.
HINT:
At the time of reassembly, please refer to the following items.
Set the motor actuator in differential lock condition.
Apply FIPG to the front case.
FIPG: Part No. 08826−00090, THREE BOND 1281 or
equivalent
Torque: 18 N·m (185 kgf·cm, 13 ft·lbf)
4. REMOVE OUTPUT GEAR FROM FRONT CASE
HINT:
At the timie of reassembly apply gear oil to the output gear.
NOTICE:
At the time of reassembly, do not turn the output gear.
5. REMOVE SCREW PLUG, SPRING AND BALL
(a) Using a torx socket wrench (T40), remove the screw plug.
HINT:
At the time of reassembly, apply liquid sealer to the screw plug. Sealant: Part No.08833−00080, THREE BOND 1344,
LOCTITE 242 or equivalent
Torque:19 N·m (190 kgf·cm, 14 ft·lbf)
(b) Using a magnetic finger, remove the spring and ball.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

TF0854
TF0986
TF0857
Q07130
RemovalInstallation
Socket Wrench Socket Wrench
TR−8
−
TRANSFER TRANSFER ASSEMBLY
1996 LAND CRUISER (RM451U)
FIPG: Part No. 08826−00090, THREE BOND 1281 or
equivalent
16. REMOVE 2 BEARING RACES FROM REAR CASE
17. REMOVE INPUT SHAFT ASSEMBLY
Using a plastic hammer, remove the input shaft assembly.
18. REMOVE IDLER GEAR ASSEMBLY, CENTER DIFFER-
ENTIAL ASSEMBLY, SHIFT FORK NO.1 AND SHIFT
FORK NO.1 SHAFT FROM FRONT CASE
19. SEPARATE SHIFT FORK NO.1 AND SHIFT FORK NO.1 SHAFT
(a) Using a pin punch and hammer, drive out the slotted spring pin.
(b) Separate the shift fork No.1 and shift fork No.1 shaft.
20. REMOVE SHIFT OUTER LEVER AND INNER LEVER
(a) Remove the nut and washer from the shift outer lever. Torque: 12 N·m (120 kgf·cm, 9 ft·lbf)
(b) Using a brass bar, hammer and socket wrench, tap out the lever lock pin.
(c) Remove the shift outer lever, washer and inner lever from
the front case.
21. REMOVE OIL RECEIVER FROM FRONT CASE
Remove the bolt and oil receiver. Torque: 12 N·m (120 kgf·cm, 9 ft·lbf)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

TR0BD−01
Q07115
SSTStamp
TF1012
TF0913
TF0917
−
TRANSFER CENTER DIFFERENTIAL
TR−21
1996 LAND CRUISER (RM451U)
REASSEMBLY
HINT:
Coat all of the sliding and rotating surfaces with gear oil before
assembly.
1. INSTALL NEEDLE ROLLER BEARING
(a) Using SST and a press, install the needle roller bearing
to the differential rear case.
SST 09612−24014 (09612 −10050)
HINT:
Install the bearing to the differential rear case, taking care that
its stamped side comes in contact with SST.
(b) Install the snap ring.
2. INSTALL LOW GEAR
(a) Clean the contact surface of the differential case.
(b) Heat the low gear in boiling water.
(c) Carefully remove the low gear from the water.
(d) After the moisture on the low gear has completely evapo- rated, quickly install the low gear to the differential case.
3. INSTALL PINION SHAFT, PINION GEAR AND THRUST
WASHER
(a) Install the front side gear and thrust washer to the differ- ential front case.
(b) Install the pinion shaft, 2 pinion gears and thrust washers
to the differential front case.
(c) Using a dial indicator, measure the front case backlash.
HINT:
Push the pinion shaft. Minimum backlash: 0.05 mm (0.0020 in.)
If the backlash is not within the specification, replace the thrust
washer with one of the correct size and reinstall the thrust wash-
er.
Thickness mm (in.)Thickness mm (in.)
1.70 (0.0669)2.45 (0.0965)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Q00546
SST
Q00555
Q00539
SSTSST
Q00540
SST
SST
TF0931
−
TRANSFER CENTER DIFFERENTIAL
TR−23
1996 LAND CRUISER (RM451U)
(c) Using SST and a press, install the high speed output gear
bushing.
SST 09316−12010, 09316 −60011 (09316−00011)
NOTICE:
Before pressing, align the holes on the bushing and shaft
so that the pin on the shaft aligned with the cutting portion
of the bushing.
11. INSTALL HIGH AND LOW CLUTCH SLEEVE
HINT:
Make sure to install the high and low clutch sleeve in the correct
direction.
12. INSTALL HIGH SPEED OUTPUT GEAR AND NEEDLE ROLLER BEARING
(a) Apply gear oil to the needle roller bearing.
(b) Install the high speed output gear and needle roller bear-
ing.
13. INSTALL FRONT TAPER ROLLER BEARING
Using SST and a press, install the front taper roller bearing. SST 09316−12010, 09316 −60011 (09316−00011)
14. INSTALL FRONT DRIVE GEAR PIECE
Using SST and a press, install the front drive gear piece. SST 09316−12010, 09316 −60011 (09316−00011)
15. INSTALL SNAP RING
(a) Select a snap ring that will allow minimum axial play.
MarkThickness mm (in.)MarkThickness mm (in.)
A2.00 (0.0787)G2.60 (0.1024)
B2.10 (0.0827)H2.70 (0.1063)
C2.20 (0.0866)J2.80 (0.1 102)
D2.30 (0.0906)K1.80 (0.0709)
E2.40 (0.0945)L1.90 (0.0748)
F2.50 (0.0984)−−
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

TR0BH−01
Q08383
Center Differential Control
Couping Assembly
Snap ring Vehicle Speed sensor
Drive Gear Ball Bearing
 Snap Ring
Snap Ring
Oil Pump Plate
Drive Rotor
Oil Pump Cover
Rear Extension housing
Oil Pump Drive Shaft Ball
Spring 
Screw Plug
Valve Seat

Dust Deflector
 Oil Seal Seal Ring
Rear Output Shaft
 Non− reusable Part
 Precoated part Separator
Driven Rotor
−
TRANSFER REAR EXTENSION HOUSING
TR−29
839
Author: Date:
1996 LAND CRUISER (RM451U)
REAR EXTENSION HOUSING
COMPONENTS
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

TR0BI−01
Q00530
Q08384
Q02549
Q07138
TR−30
−
TRANSFER REAR EXTENSION HOUSING
1996 LAND CRUISER (RM451U)
DISASSEMBLY
1. REMOVE OIL PUMP DRIVE SHAFT
2. REMOVE OIL PUMP COVER
(a) Using a torx socket wrench (T30), remove the 3 screws.
(b) Install the 2 suitable bolts to the pump cover.
(c) Remove the pump cover from the rear extension housing.
3. REMOVE DRIVE ROTOR FROM DRIVEN ROTOR
4. REMOVE DRIVEN ROTOR FROM REAR EXTENSION HOUSING
5. REMOVE SCREW PLUG, SPRING, BALL AND VALVE SEAT
(a) Using a hexagon wrench, remove the screw plug.
(b) Using a magnetic finger, remove the spring, ball and valve
seat from the rear extension housing.
6. REMOVE CENTER DIFFERENTIAL CONTROL COU- PLING ASSEMBLY
(a) Using a snap ring expander, remove the snap ring.
(b) Remove the coupling assembly from the rear extension housing.
7. REMOVE SEPARATOR AND OIL PUMP PLATE
Remove the 3 bolts, separator and oil pump plate.
8. REMOVE VEHICLE SPEED SENSOR DRIVE GEAR
(a) Using a snap ring expander, remove the snap ring.
(b) Remove the vehicle speed sensor drive gear.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

TF0969
SST
TF0958
Q07138
Q02549
Q08384
TR−34
−
TRANSFER REAR EXTENSION HOUSING
1996 LAND CRUISER (RM451U)
4. INSTALL REAR OUTPUT SHAFT
(a) Using SST and a press, install the rear output shaft.
SST 09316−20011, 09316 −60011 (09316−00011,
09316 −00031)
(b) Install the 2 seal rings to the rear output shaft.
(c) Select a snap ring that will allow minimum axial play.
MarkThickness mm (in.)
11.95 (0.0768)
22.05 (0.0807)
32.15 (0.0847)
42.25 (0.0886)
(d) Using a snap ring expander, install a new snap ring.
5. INSTALL VEHICLE SPEED SENSOR DRIVE GEAR
(a) Install the vehicle speed sensor drive gear.
(b) Using a snap ring expander, install the snap ring.
6. INSTALL OIL PUMP PLATE AND SEPARATOR
(a) Install the oil pump plate.
(b) Install the separator.
(c) Install and torque the 3 bolts. Torque: 4.9 N·m (50 kgf·cm, 43 in.·lbf)
7. INSTALL CENTER DIFFERENTIAL CONTROL COU- PLING ASSEMBLY
(a) Install the coupling assembly to the output shaft.
(b) Using a snap ring expander, install the snap ring.
8. INSTALL VALVE SEAT, BALL, SPRING AND SCREW PLUG
(a) Apply gear oil to the ball.
(b) Install the valve seat, ball and spring.
(c) Apply liquid sealer to the screw plug.
Sealant: Part No. 08833−00080, THREE BOND 1344,
LOCTITE 242 or equivalent
(d) Using a hexagon wrench, install and torque the screw plug.
Torque: 29 N·m (300 kgf·cm, 22 ft·lbf)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010