1996 TOYOTA LAND CRUISER service

H00059
TerminalTime of Body Ground
Tc
Tc
ABOFF
AB
Body
GroundON
OFF
Body
Ground
”1”
”2” ”3”
”4””5”
OFF
1 second
( ± 0.5 sec.) 1 second
( ± 0.5 sec.)
Several
seconds
50 m sec.
50 m sec.
R13819
DI−242
−
DIAGNOSTICS SUPPLEMENTAL RESTRAINT SYSTEM
1996 LAND CRUISER (RM451U)
4. DTC CLEARANCE (Using diagnosis check wire)
(a) Connect the 2 service wires to terminals Tc and AB of
DLC1.
(b) Turn the ignition switch to ACC or ON and wait approx. 6 seconds.
(c) Starting with the Tc terminal, apply body ground alternate-
ly to terminal Tc and terminal AB twice each in cycles of
1.0 seconds. Confirm that body ground is absolute.
Finally, keep applying body ground to terminal Tc.
HINT:
When alternately grounding terminals Tc and AB, release
ground from one terminal and immediately apply it to the other
terminal within an interval of 0.2 second. If DTCs do not clear,
repeat the above procedure until the codes are cleared.
(d) Several seconds after doing the clearing procedure, the SRS waring light will blink in a 50 m sec. cycle to indicate
the codes have been cleared.
5. USING TOYOTA HAND−HELD TESTER
(a) Hook up the TOYOTA hand−held tester to the DLC1.
(b) Clear the DTC by following the prompts on the tester
screen.
HINT:
Please refer to the T OYOTA hand −held tester operator ’s manu-
al for further details.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

AB0069
W01933
AB0118
R13006AB0069
AB0118
W02042
H00006
Airbag Sensor
Assembly
Spiral
Cable
P Squib
D Squib P+
P−
D+
D− ACC
ON
or
Code 11
DLC1
Tc
E1
DI−250
−
DIAGNOSTICS SUPPLEMENTAL RESTRAINT SYSTEM
1996 LAND CRUISER (RM451U)
4 Check airbag sensor assembly.
PREPARATION:
(a) Connect connector to airbag sensor assembly.
(b) Using service wire, connect D
+ and D− on spiral cable side
of connector between spiral cable and steering wheel
pad.
(c) Using a service wire, connect P
+ and P− on airbag sensor
assembly side of connector between airbag sensor as-
sembly and front passenger airbag assembly.
(d) Connect negative ( −) terminal cable to battery, and wait
at least 2 seconds.
CHECK:
(a) Turn ignition switch to ACC or ON and wait at least 20 se-
conds.
(b) Clear malfunction code stored in memory. (See page DI−240 )
(c) Turn ignition switch to LOCK, and wait at least 20 se- conds.
(d) Turn ignition switch to ACC or ON, and wait at least 20 se-
conds.
(e) Using SST, connect terminals Tc and E1 of DLC1. SST 09843−18020
(f) Check DTC
OK:
DTC 11 is not output.
HINT:
Codes other than code 11 may be output at this time, but they
are not relevant to this check.
NG Replace airbag sensor assembly.
OK
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

AB0069
AB0069
AB0118
R13006AB0119W01933
W02043 H00012
Airbag Sensor
Assembly
P+
P−
Spiral
Cable
P Squib
D Squib D− D+ ACC ON
or
DLC1 Code 12
E1 Tc
DI−256
−
DIAGNOSTICS SUPPLEMENTAL RESTRAINT SYSTEM
1996 LAND CRUISER (RM451U)
4 Check airbag sensor assembly.
PREPARATION:
(a) Connect connector to airbag sensor assembly.
(b) Using a service wire, connect D
+ and D− on spiral cable
side of connector between spiral cable and steering
wheel pad.
(c) Using a service wire, connect P
+ and P− on airbag sensor
assembly side of connector between airbag sensor as-
sembly and front passenger airbag assembly.
(d) Connect negative ( −) terminal cable to battery, and wait
at least 2 seconds.
CHECK:
(a) Turn ignition switch to ACC or ON, and wait at least 20 se-
conds.
(b) Clear malfunction code stored in memory. (See page DI−240 )
(c) Turn ignition switch to LOCK, and wait at least 20 se- conds.
(d) Turn ignition switch to ACC or ON, and wait at least 20 se-
conds.
(e) Using SST, connect terminals Tc and E1 of DLC1. SST 09843−18020
(f) Check DTC.
OK:
DTC 12 is not output.
HINT:
Codes other than code 12 may be output at this time, but they
are not relevant to this check.
NG Replace airbag sensor assembly.
OK
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

W02055
R14286 R12688H00016
Airbag Sensor
Assembly
Spiral
Cable
P Squib
D Squib D+
D−
D−
D+
−
DIAGNOSTICS SUPPLEMENTAL RESTRAINT SYSTEM
DI−261
1996 LAND CRUISER (RM451U)
2 Check D squib circuit.
PREPARATION:
Using service wire, connect D+ and D− on airbag sensor assem-
bly connector.
CHECK:
For the connector (on the spiral cable side) between the spiral
cable and steering wheel pad, measure the resistance between
D
+ and D−.
OK:
Resistance: Below 1 Ω
NG Go to step 5.
OK
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

R05895
AB0118
R13006AB0069
AB0119
W02044
H00017
Airbag
Sensor
Assembly
Spiral
Cable
D Squib P Squib
D+
D− ACC
ON
or
DLC1
E1 Tc Code 14
DI−262
−
DIAGNOSTICS SUPPLEMENTAL RESTRAINT SYSTEM
1996 LAND CRUISER (RM451U)
3 Check airbag sensor assembly.
PREPARATION:
(a) Connect connector to airbag sensor assembly.
(b) Using a service wire, connect D+ and D− on spiral cable
side of connector between spiral cable and steering
wheel pad.
(c) Connect negative ( −) terminal cable to battery, and wait
at least 2 seconds.
CHECK:
(a) Turn ignition switch to ACC or ON and wait at least 20 se-
conds.
(b) Clear malfunction code stored in memory. (See page DI−240 )
(c) Turn ignition switch to LOCK, and wait at least 20 se-
conds.
(d) Turn ignition switch to ACC or ON, and wait at least 20 se-
conds.
(e) Using SST, connect terminals Tc and E1 of DLC1.
SST 09843−18020
(f) Check DTC.
OK:
DTC 14 is not output.
HINT:
Codes other than code 14 may be output at this time, but they
are not relevant to this check.
NG Replace airbag sensor assembly.
OK
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

R05899
R14286H00019
P SquibD+
D− Airbag
Sensor
Assembly
Spiral
Cable
D Squib
W01932
R14286 R12688H00020
Airbag
Sensor
Assembly
Spiral
Cable
P Squib
D Squib D−
D+
D+
D−
DI−264
−
DIAGNOSTICS SUPPLEMENTAL RESTRAINT SYSTEM
1996 LAND CRUISER (RM451U)
5 Check spiral cable.
PREPARATION:
Disconnect connector between airbag sensor assembly and
spiral cable.
CHECK:
For the connector (on the spiral cable side) between the spiral
cable and steering wheel pad, measure the resistance D
+ and
D
−.
OK:
Resistance: Below 1 Ω
NG Repair or replace spiral cable.
OK
6 Check harness between airbag sensor assembly and spiral cable.
PREPARATION:
Using service wire, connect D+ and D− on airbag sensor assem-
bly connector.
CHECK:
For the connector (on the airbag sensor assembly side) be-
tween the airbag sensor assembly and spiral cable, measure
the resistance between D
+ and D−.
OK:
Resistance: Below 1 Ω
NG Repair or replace harness or connector be- tween airbag sensor assembly and spiral cable.
OK
From the results of the above inspection, the malfunctioning part can no\
w be considered normal.
To make sure of this, use the simulation method to check.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

R14287
W01936R12689H00023
Airbag
Sensor
Assembly
Spiral
Cable
P Squib
D Squib P−
P+
P+
P−
DI−268
−
DIAGNOSTICS SUPPLEMENTAL RESTRAINT SYSTEM
1996 LAND CRUISER (RM451U)
INSPECTION PROCEDURE
1 Preparation. (See step 1 on page DI−271)
2 Check P squib circuit.
PREPARATION:
Using service wire, connect P+ and P− on airbag sensor assem-
bly connector.
CHECK:
For the connector (on the airbag sensor assembly side) be-
tween the airbag sensor assembly and front passenger airbag
assembly measure the resistance between P
+ and P−.
OK:
Resistance: Below 1 Ω
NG Repair or replace harness or connector be- tween airbag sensor assembly and front pas-
senger airbag assembly.
OK
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

AB0069
AB0118
R13006W01934
AB0119
W02045
H00024
P+
P−
Airbag Sensor
Assembly
P Squib
D Squib Spiral
Cable
ACC ON
or
DLC1
E1 Tc Code 54
−
DIAGNOSTICS SUPPLEMENTAL RESTRAINT SYSTEM
DI−269
1996 LAND CRUISER (RM451U)
3 Check airbag sensor assembly.
PREPARATION:
(a) Connect connector to airbag sensor assembly.
(b) Using service wire, connect P
+ and P− on airbag sensor
assembly side of connector between airbag sensor as-
sembly and front passenger airbag assembly.
(c) Connect negative ( −) terminal cable to battery, and wait
at least 2 seconds.
CHECK:
(a) Turn ignition switch to ACC or ON, and wait at least 20 se-
conds.
(b) Clear malfunction code stored in memory. (See page DI−240 )
(c) Turn ignition switch to LOCK, and wait at least 20 se-
conds.
(d) Turn ignition switch to ACC or ON, and wait at least 20 se-
conds.
(e) Using SST, connect terminals Tc and E1 of DLC1.
SST 09843−18020
(f) Check DTC.
OK:
DTC 54 is not output.
HINT:
Codes other than code 54 may be output at this time, but they
are not relevant to this check.
NG Replace airbag sensor assembly.
OK
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010