1996 TOYOTA LAND CRUISER Terminal

Z09805
Connector ”A”Connector ”B”
−
AIR CONDITIONING AIR CONDITIONING CONTROL ASSEMBLY
AC−71
1996 LAND CRUISER (RM451U)
5. A/C or DEF Switch:
INSPECT INDICATOR LIGHT OPERATION
(a) Connect the positive (+) lead from the battery to terminal
A−9 and the negative ( −) lead to terminal B−18.
(b) Push the A/C or DEF switch button in and check that the indicator light lights up.
(c) Then, connect the positive (+) lead from the battery to ter-
minal A−13 and check that the indicator dims.
If operation is not as specified, replace the A/C control assem-
bly.
6. INSPECT AIR INLET CONTROL SWITCH CONTINUITY
Switch positionTester connectionSpecified condition
FRESHA8 − A19Continuity
RECIRCA8 − A18Continuity
If continuity is not as specified, replace the A/C control assem-
bly.
7. INSPECT MODE CONTROL SWITCH CONTINUITY
Switch positionTester connectionSpecified condition
FACEA14 − B16Continuity
BI−LEVELA12 − B16Continuity
FOOTA7 − B16Continuity
FOOT −DEFB11 − B16Continuity
DEFB4 − B16Continuity
If continuity is not as specified, replace the A/C control assem-
bly.
8. INSPECT BLOWER SPEED CONTROL SWITCH CON-
TINUITY
Switch positionTester connectionSpecified condition
OFFA10 − B16Continuity
LOA1 − B16Continuity
M1B9 − B16Continuity
M2B10 − B16Continuity
HIB13 − B16Continuity
Connector"A"
Connector"B"
Connector"A"
Connector"A"
...-~~IIB1~t•7 ,3 2I
20Itl'17"lIB,,113121110
e-20-2-C
In,•71'fIl';;l1oT~312I1\
[20It..117,,110141131211110II
0-20-2-<:.-18-2-B
AC2726
AC2727
219129
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

AC−72
−
AIR CONDITIONING AIR CONDITIONING CONTROL ASSEMBLY
1996 LAND CRUISER (RM451U)
If continuity is not as specified, replace the A/C control assem-
bly.
9. INSPECT A/C OR DEF SWITCH CONTINUITY
Check that there is continuity between terminals B− 6 and B−17
intermittently each time the A/C or DEF switch button pressed.
If continuity is not as specified, replace the A/C control assem-
bly.
10. INSPECT TEMPERATURE CONTROL SWITCH RESIS-
TANCE
(a) Measure resistance between terminals B −1 and B−2.
Standard resistance:
Approx. 3.0 kΩ
(b) Check that the resistance between terminals B −1 and
B−3 increases from 0 to approx. 3.0 k Ω when the switch
knob is turned from COOL to HOT.
If operation is not as specified, replace the A/C control assem-
bly.
e·18·2·B
e-18-2-B
Connector"B"
!Ie7615[ll'O'H(13IU2In
~1817161151(113121111JlIO'Jl
Connector"B"
N06436
N06436
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Z04536
AC2SO−04
Z15447
−
AIR CONDITIONING REAR HEATER SWITCH
AC−77
1404
Author: Date:
1996 LAND CRUISER (RM451U)
REAR HEATER SWITCH
INSPECTION
1. REMOVE INSTRUMENT CLUSTER FINISH CENTER
PANEL WITH A/C CONTROL ASSEMBLY
2. REMOVE REAR HEATER SWITCH
3. INSPECT INDICATOR OPERATION
(a) Connect the positive (+) lead from the battery to terminal
5 and the negative ( −) lead to terminal 1.
(b) Push each of the rear heater switch knob in and check
that their indicators lights up.
If operation is not as specified, replace the switch.
4. INSPECT SWITCH CONTINUITY
Switch positionTester connectionSpecified condition
HI1 − 4Continuity
OFF−No Continuity
LO1 − 2Continuity
Illumination circuit3 − 6Continuity
If continuity is not as specified, replace the switch.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Z16656
BC
KLS
E
STP SLS−
ACC
IG A
SLS+
AT0T7−04
Q07316
Ohmmeter
Q07315Battery
−
AUTOMATIC TRANSMISSION SHIFT LOCK SYSTEM
AT−13
1996 LAND CRUISER (RM451U)
INSPECTION
1. INSPECT SHIFT LOCK CONTROL ECU
Using a voltmeter, measure the voltage at each terminal.
HINT:
Do not disconnect the ECU connector.
2. INSPECT SHIFT LOCK SOLENOID
(a) Disconnect the solenoid connector.
(b) Using an ohmmeter, measure the resistance between ter-
minals.
Standard resistance: 20 − 28 Ω
If the resistance is not as specified, replace the solenoid.
(c) Apply the battery positive voltage between terminals. At this time, confirm that solenoid operate.
If the operation is not as specified, replace the solenoid.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Q07314
P1P2
P
AT
−14
−
AUTOMATIC TRANSMISSION SHIFT LOCK SYSTEM
1996 LAND CRUISER (RM451U)
3. INSPECT KEY INTERLOCK SOLENOID
(a) Disconnect the solenoid connector.
(b) Using an ohmmeter, measure the resistance between ter-
minals 7 and 8.
Standard resistance: 12 − 17 Ω
If the resistance is not as specified, replace the solenoid.
4. INSPECT SHIFT LOCK CONTROL SWITCH
Inspect that there is continuity between each terminal.
Shift positionTester condition to
terminal numberSpecified value
P position (Release
button is not pushed)P1 − PContinuity
P position (Release
button is pushed)P1 − P
P2 − PContinuity
R, N, D, 2, L positionP2 − PContinuity
If the continuity is not as specified, replace the switch.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Q07409
AT−24
−
AUTOMATIC TRANSMISSION AUTOMATIC TRANSMISSION UNIT
1996 LAND CRUISER (RM451U)
(d) Remove the 4 nuts and 2 gaskets, shift the front exhaust
pipe assembly to the vehicle’s outside.
Torque: 62 N·m (630 kgf·cm, 46 ft·lbf)
HINT:
At the time of installation, replace the used gaskets and nuts
with new gaskets and nuts.
15. REMOVE STARTER
(a) Remove the nut and disconnect the terminal and connec-
tor.
(b) Remove the lower side mounting bolt and starter. Torque: 39 N·m (400 kgf·cm, 29 ft·lbf)
16. REMOVE CROSSMEMBER
(a) Support the transmission with a transmission jack.
(b) Remove the 8 bolts and 2 nuts, and then remove the crossmember.
Torque:
Bolt: 61 N·m (620 kgf·cm, 45 ft·lbf)
Nut: 74 N·m (750 kgf·cm, 54 ft·lbf)
17. REMOVE TRANSMISSION
(a) Lower the rear end of the transmission.
NOTICE:
Be careful not to damage the cooling fan, brake booster
and brake line.
(b) Separate the wire harness from the transmission and transfer.
(c) Remove the oil cooler pipe mounting bolts from the torque
converter clutch housing, and then disconnect the 2 oil
cooler pipes from the elbows.
(d) Remove the 10 bolts and transmission. Torque: 72 N·m (730 kgf·cm, 53 ft·lbf)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE1LS−01
−
BODY ELECTRICAL BODY ELECTRICAL SYSTEM
BE−1
1139
Author: Date:
1996 LAND CRUISER (RM451U)
BODY ELECTRICAL SYSTEM
PRECAUTION
Take care to observe the following precautions when performing inspections o\
r removal and replacement
of body electrical related parts.
1. HEADLIGHT SYSTEM
Halogen bulbs have pressurized gas inside and require special handling. They ca\
n burst if scratched or
dropped. Hold a bulb only by its plastic or metal case. Don’t touch the glass\
part of a bulb with bare hands.
2. SRS (SUPPLEMENTAL RESTRAINT SYSTEM)
The LAND CRUISER is equipped with an SRS (Supplemental Restraint System) such as the driver airbag
and front passenger airbag. Failure to carry out service operation in th\
e correct sequence could cause the
SRS to unexpectedly deploy during servicing, possibly leading to a serious accident. Before servicing (in\
-
cluding removal or installation of parts, inspection or replacement), be sure t\
o read the precautionary notices
in the RS section.
3. AUDIO SYSTEM
If the negative (−) terminal cable is disconnected from the battery, the preset AM, FM 1 and FM 2 stations
stored in memory are erased, so be sure to note the stations and reset them af\
ter the negative ( −) terminal
cable is reconnected to the battery.
4. MOBILE COMMUNICATION SYSTEM
If the vehicle is equipped with a mobile communication system, refer to \
precautions in the IN section.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE1LZ−01
BE−14
−
BODY ELECTRICAL HEADLIGHT AND TAILLIGHT SYSTEM
1996 LAND CRUISER (RM451U)
INSPECTION
1. INSPECT LIGHT CONTROL SWITCH CONTINUITY
Switch positionTester connectionSpecified condition
OFF−No continuity
TAILA2 − A11Continuity
HEADA2 − A11 − A13Continuity
If continuity is not as specified, replace the switch.
2. INSPECT HEADLIGHT DIMMER SWITCH CONTINU-
ITY
Switch positionTester connectionSpecified condition
FlashA9 − A12 − A14Continuity
Low beamA3 − A9Continuity
High beamA9 − A12Continuity
If continuity is not as specified, replace the switch.
3. INSPECT HEADLIGHT CONTROL RELAY CONTINU-
ITY
ConditionTester connectionSpecified condition
Constant1 − 2Continuity
Apply B+ between
terminals 1 and 2.3 − 4Continuity
If continuity is not as specified, replace the relay.
4. INSPECT TAILLIGHT CONTROL RELAY CONTINUITY
ConditionTester connectionSpecified condition
Constant1 − 2Continuity
Apply B+ between
terminals 1 and 2.2 − 3Continuity
If continuity is not as specified, replace the relay.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010