1996 TOYOTA LAND CRUISER Terminal

N14295
AC2S9−01
−
AIR CONDITIONING THERMISTOR
AC−59
1386
Author: Date:
1996 LAND CRUISER (RM451U)
THERMISTOR
ON−VEHICLE INSPECTION
1. REMOVE GLOVE COMPARTMENT PARTS
(See page BO−76 )
2. INSPECT THERMISTOR RESISTANCE
Measure the resistance between terminals.
Standard resistance:
1,500 Ω at 25 ° C (77 °F)
If resistance is not as specified, replace the sensor.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

N16452
AC2SB−01
Z13470
Low Pressure Side
ON (Continuity)
196 kpa
(2.0 kgf·cm
2, 28 psi)
OFF (No Continuity) High Pressure Side
3,140 kpa
(32.0 kgf·cm2, 455 psi)
OFF (No Continuity)
−
AIR CONDITIONING PRESSURE SWITCH
AC−61
1388
Author: Date:
1996 LAND CRUISER (RM451U)
PRESSURE SWITCH
ON−VEHICLE INSPECTION
1. INSTALL MANIFOLD GAUGE SET
2. DISCONNECT CONNECTOR FROM PRESSURE
SWITCH
3. RUN ENGINE AT APPROX. 1,500 RPM
4. INSPECT PRESSURE SWITCH OPERATION
(a) Connect the positive (+) lead from the ohmmeter to termi-
nal 2 and the negative ( −) lead to terminal 1.
(b) Check continuity between terminals when refrigerant pressure is changed, as shown in the illustration.
If operation is not as specified, replace the pressure switch.
5. STOP ENGINE AND REMOVE MANIFOLD GAUGE
SET
6. CONNECT CONNECTOR TO PRESSURE SWITCH
~11L
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Z19533
1
2
3
4
5 12
3
4
5
AC2SE−03
AC−64
−
AIR CONDITIONING HEATER MAIN RELAY
1391
Author: Date:
1996 LAND CRUISER (RM451U)
HEATER MAIN RELAY
INSPECTION
INSPECT HEATER MAIN RELAY CONTINUITY
ConditionTester connectionSpecified condition
Constant1 − 3
2 − 4Continuity
Apply B+ between
terminals 3 and 5.4 − 5Continuity
If continuity is not as specified, replace the relay.
BE1850 BElS44
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Z09804
1
23
4
5
6
1
3
6 2
4
AC2SF−01
−
AIR CONDITIONING REAR HEATER RELAY
AC−65
1392
Author: Date:
1996 LAND CRUISER (RM451U)
REAR HEATER RELAY
INSPECTION
INSPECT REAR HEATER RELAY CONTINUITY
ConditionTester connectionSpecified condition
Constant2 − 6
1 − 3Continuity
Apply B+ between
terminals 2 and 6.1 − 4Continuity
If continuity is not as specified, replace the relay.
H-8-2BE1844
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Z09507
1
2
3
4 412
4
3AC2SG−01
AC−66
−
AIR CONDITIONING MAGNETIC CLUTCH RELAY
1393
Author: Date:
1996 LAND CRUISER (RM451U)
MAGNETIC CLUTCH RELAY
INSPECTION
INSPECT MAGNETIC CLUTCH RELAY CONTINUITY
ConditionTester connectionSpecified condition
Constant1 − 3 Continuity
Apply B+ between
terminals 1 and 3.2 − 4Continuity
If continuity is not as specified, replace the relay.BE1647BE1841
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

N06549
AC2SH−01
V02084OFFON
103 °C (217° F)
108
°C (226° F)
−
AIR CONDITIONING ENGINE COOLANT TEMPERATURE (ECT) CUT
RELAYAC−67
1394
Author: Date:
1996 LAND CRUISER (RM451U)
ENGINE COOLANT
TEMPERATURE (ECT) CUT RELAY
INSPECTION
INSPECT SWITCH CONTINUITY
Check the continuity betweeen terminals of the switch, as
shown in the chart below.
If continuity is not as specified, replace the switch.
_tf
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

AC2SM−01
AC2717
Connector ”A”
−
AIR CONDITIONING AIR CONDITIONING CONTROL ASSEMBLY
AC−69
1996 LAND CRUISER (RM451U)
INSPECTION
1. INSPECT ILLUMINATION OPERATION
Connect the positive (+) lead from the battery to terminal A −13
and the negative ( −) lead to terminal A−3, then check that the
illuminations light up.
If illuminations do not light up, test the bulb.
2. Air Inlet Control Switch:
INSPECT INDICATOR LIGHT OPERATION
(a) Connect the positive (+) lead from the battery to terminal
A−9 and the negative ( −) lead to terminal A−8.
(b) With the air inlet control button pushed in, check that the FRESH or RECIRC indicator light lights up.
(c) Next, push in the button again, and check that the indica-
tor light goes off and the other indicator light lights up.
AICSwitch
.-20-2-CN06571 .-18-2-B
ModeControlSwitch
2=i=~~~:=i~;=j::;5-H--+__Blower Speed
ControlSwitch
TemperatureControl
Switch Connector
"A"
~~.~r-r""""~~~9&ru7 6ill'O'~5 •U3 2
1
20 19iJl
II1716115a1311121110...... L.....-~
Connector"B"
,...,.....-~~'is"'-"'r"""".~~r"'-&765~'o"~•3ru2I
1&17iJl1615ullJ12IliJllO9L...,..L-,_\-L..,-
Z04530
r
!rfl176~54 3 21~
m2019lI:8171611514131211~
Connector"A"
~e@j
AC2718
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

AC2722
Connector ”A”Connector ”B”
AC2723
Connector ”A”
Connector ”B”
AC2722
Connector ”A”
Connector ”B”
AC2723
Connector ”A”
Connector ”B”
AC−70
−
AIR CONDITIONING AIR CONDITIONING CONTROL ASSEMBLY
1996 LAND CRUISER (RM451U)
(d) Then connect the positive (+) lead from the battery to ter-
minal A−13 and check that the indicator dims.
If operation is not as specified, replace the A/C control assem-
bly.
3. Mode Control Switch: INSPECT INDICATOR LIGHT OPERATION
(a) Connect the positive (+) lead from the battery to terminal A−9 and the negative ( −) lead to terminal B−16.
(b) Push each of the mode buttons in and check that their in- dicator light lights up.
(c) Then connect the positive (+) lead from the battery to ter-
minal A−13 and check that the indicator dims.
If operation is not as specified, replace the A/C control assem-
bly.
4. Blower Speed Control Switch: INSPECT INDICATOR LIGHT OPERATION
(a) Connect the positive (+) lead from the battery to terminal A−9 and the negative ( −) lead to terminal B−16.
(b) Push each of the blower speed control buttons in and check that their indicator light lights up.
(c) Then connect the positive (+) lead from the battery to ter-
minal A−13 and check that the indicator dims.
If operation is not as specified, replace the A/C control assem-
bly.
c
r
1rf1~716[lJ';W5413 211
1\E~g1~171611514[.3]12111~
-r...'onnector"A"(
IeCBI
AC2719
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010